Ring Floodlight Cam Wired Pro manual

Ring Floodlight Cam Wired Pro
7.5 · 1
PDF manual
 · 8 pages
manualRing Floodlight Cam Wired Pro
Support centre

How to Use

How can we help?
Ring Floodlight Cam Wired Pro Installation Guide
Before you begin
WARNING: Electrical shock hazard. Disconnect power to the installation area at your circuit breaker
or fuse box before beginning installation. Always use caution when handling electrical wiring.
Installation by a qualified electrician may be required in your area. Refer to your local laws and
building codes before performing electrical work; permits plus professional installation may be
required by law.
Turn off power at the fuse box before installing.
Verify that the supply voltage is correct. Connect fixture to a 100~240 VAC 50/60 Hz power
The Earth wire must be connected to the light fixture. DO NOT INSTALL if a working earth
connection is not available.
Do not connect this light fixture to a dimmer switch or timer.
CAUTION: Risk of fire
Do not install near combustible or flammable surfaces. Floodlight Cam Wired Pro must be installed
on a wall or eve.

Installation Steps

To install your Floodlight Cam Wired Pro device, follow these steps:
1. Open the Ring app and select Set Up a Device. Then follow the in-app instructions.
2. Scan this code. This identifies your Ring device to make setup fast and easy.

View the manual for the Ring Floodlight Cam Wired Pro here, for free. This manual comes under the category Security cameras and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Ring Floodlight Cam Wired Pro or do you need help? Ask your question here

Need help?

Do you have a question about the Ring and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Ring owners to provide you with a good answer.

Dennis Alessio • 17-1-2023No comments

I have good wi fi but I don't get the Ring app to show up. I have 3 Floodlight Cam Wired Pro units. any suggestions on how to get the connection to the app to allow set up. Right now you put switch on and lights come on for maybe 30 sec. then go out. when u walk bye then the sensor flashes but no lights come on

Answer this question
karleen mcleod • 13-12-2022No comments

I want to print a copy of user instructions for me new ring flood cam. where do I find them so I can print them?

Answer this question

Number of questions: 2

Floodlight Cam Wired Pro | 8SF1E1-BEU0
Security camera
User manual (PDF)
TypeIP security camera
Placement supportedOutdoor
Connectivity technologyWireless
Luminous flux2000 lm
Colour temperature3000 K
Day/night mode
Built-in light
Built-in HDD-
Motion sensor
Built-in siren
Video motion detection
Form factor-
Mounting typeCeiling/wall
Product colourBlack
Country of originChina
Lens viewing angle, horizontal140 °
Lens viewing angle, vertical80 °
Power source typeAC
AC input voltage100 - 240 V
Image sensor
Sensor type-
Lens system
Number of lenses1
Zoom capability
Operational conditions
Operating temperature (T-T)-28 - 48 °C
Weight & dimensions
Depth202 mm
Height217 mm
Width326 mm
Package width16.3 mm
Package depth360 mm
Package height24.8 mm
Night vision
Night vision
Packaging content
Mounting brackets included
Number of cameras1
Battery included
Total megapixels- MP
Supported video modes1080p
Maximum resolution- pixels
Video streaming
Ethernet LAN-
Networking standardsIEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Live view
Logistics data
Harmonized System (HS) code85258900
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Ring Floodlight Cam Wired Pro below.

Is your question not listed? Ask your question here

No results