PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC NO

Copyright © 2021 VARO P a g i n a | 7 www.varo.com
240
K: Fingerslipepute
Slipepute for fingerslipepapir.
L: Fingerslipepapir
Fingerslipepapir med ulik kornstørrelse:
120
180
240
8.3.2 Saging
Bruk kun uskadede, feilfrie sagblad. Bøyde, uskarpe eller ellers skadede
sagblader kan brekke.
Det må kun bearbeides myke materialer som tre, gipskartong o.l. med
dykksagemetoden!
Før saging med sagblader i tre, sponplater, byggematerialer osv., bør disse sjekkes for
fremmedlegemer som spiker, skruer og lignende. Om nødvendig må disse objektene fjernes,
eller du må skifte til metallsagblad.
8.3.3 Sliping
Slipemengden og slipebildet bestemmes vesentlig med valget av slipeskive, forhåndsinnstilt
svingtallstrinn og presstrykket.
Kun feilfrie slipeskiver gir bra slipeeffekt og skåner elektroverktøyet.
Pass på jevnt presstrykk, for å øke levetiden til slipeskivene.
En stor øking av presstrykket fører ikke til en høyere slipeeffekt, men til en sterkere slitasje av
elektroverktøyet og slipeskiven.
Til en punkt-nøyaktig sliping av hjørner, kanter og områder som er vanskelig tilgjengelige kan
du også arbeide med spissen eller en kant på slipesålen.
Ved punktuell sliping kan slipeskiven varmes sterkt opp. Reduser svingtallet og la slipeskiven
avkjøles med jevne mellomrom.
En slipeskive som ble brukt til bearbeidelse av metall, må ikke lenger brukes til andre
materialer.
8.3.4 Skraping
Velg et høyt svingtalltrinn til skraping. Arbeid på en myk undergrunn (f.eks. tre) i flat vinkel og
med lite presstrykk. Sparkelen kan ellers skjære inn i undergrunnen.

9 RENGJØRING OG VEDLIKEHOLD

Trekk støpslet ut av stikkontakten før du utfører noe arbeid på maskinen.
Hold ventilasjonssporene på maskinen rene for å unngå at motoren overopphetes.
Rengjør maskinhuset regelmessig jevnlig med en myk klut, helst etter hver gangs bruk.
Sørg for at ventilasjonssporene er fri for støv og skitt.
Gjenstridig skitt fjernes med en myk klut som er fuktet med såpevann.
Bruk ikke løsemidler som bensin, alkohol, ammoniakk osv. Slike stoffer skader
kunststoffdelene.
Pass på at det ikke kommer vann inn i et elektrisk verktøy.

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results