PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC NO

Copyright © 2021 VARO P a g i n a | 6 www.varo.com
ADVARSEL: Dette verktøyet bruker spesielle hurtigverktøy. Ikke bruk som
ikke er beregnet på maskinen.
ADVARSEL: Kontroller at det påmonterte verktøyet sitter godt festet.
Feilaktig eller dårlig festet verktøy kan løsne under bruk og utgjøre en fare.
7.2 Montere/skifte slipepapir (Fig. 2)
Med hurtig krok- og utløsersystem.
Plasser slipepapiret og trykk det på for hånd.
Press slipepapiret på plass ved å gi det et kort og bestemt trykk mot slipeplatens overflate
(12), og slå verktøyet på.
Dette sørger for godt feste og hindrer for tidlig slitasje.
Hvis spissen slites, trekker du slipepapiret av, dreier det 120 grader og fester det igjen,
eventuelt kan du skifte slipepapir.
7.3 Montere støvavtrekk (Fig. 4)
Ta støvadapteren (10) og skru den på bunnen av maskinen. Husk at skruen må være på
bunne av støvadapteren. På denne måten kan skru den lett inn i skruehullet. Etter at denne
delen er montert på maskinen, kan du feste støvrøret (11) på støvadapteren. Gi røret et
bestemt trykk. Du kan alltid justere retningen til røret ved å bevege det litt i ønsket retning.

8 BRUK

8.1 Slå PÅ/AV (Fig. 5)
Kontroller først at strømledningen og støpslet er uten skade.
Sett støpslet i stikkontakten.
Slå verktøyet PÅ: Skyv PÅ/AV-bryteren (2) frem til på-stillingen (I).
Slå verktøyet AV: Skyv PÅ/AV-bryteren bakover til av-stillingen (O).
8.2 Hastighetsjustering (Fig. 6)
Verktøyet kan justeres til 6 forskjellige hastigheter. Posisjonen "1" indikerer laveste hastighet,
mens "6" indikere høyeste hastighet. Du justerer hastigheten ved å dreie hastighetsvelgeren
(4) fra posisjon "1" til "6". Operatøren må kanskje variere hastigheten for å oppnå best mulig
resultat.
8.3 Tips om bruken
8.3.1 Valg av innsatsverktøy
Tilbehør (Fig. 7)
Materiale
A: 3,2cm sagblad
Trematerialer, plast, metall, gips og andre myke materialer.
B: 6,5cm sagblad
Trematerialer, plast, metall, gips og andre myke materialer.
C: 2,0cm sagblad
Trematerialer, plast, metall, gips og andre myke materialer.
D: 1,0cm sagblad
Trematerialer, plast, metall, gips og andre myke materialer.
E: 8,5cm segmentblad
Trematerialer, plast, metall, gips og andre myke materialer.
F: 5,2cm skrapeblad
Egner seg for fjerning av maling og tepper.
G: 9,3cm karbid segmentblad
Kutter spor i tørrmur, mørtel, lettbetong og lignende
materialer.
H: 3,2cm karbidblad
Kutter spor i tørrmur, mørtel, lettbetong og lignende
materialer.
I: Trekantet slipepute
Slipepute for slipepapir av størrelse 90x90x90.
J: Trekantet slipepapir
Slipepapir med ulik kornstørrelse:
120
180

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results