PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC PT

Copyright © 2021 VARO P á g i n a | 6 www.varo.com

7 MONTAGEM

AVISO: Verifique sempre se a fonte de alimentação corresponde à tensão
na placa de características. Remova a ferramenta elétrica da embalagem.
Não ligue à tomada antes de montar.
7.1 Montar o disco de lixa/ lâmina de serra/ espátula (Fig. 1)
AVISO: Antes de montar e fazer ajustes desligue sempre a ficha da tomada.
Tenha cuidado com ferramentas afiadas tais como espátulas, lâminas de serra ou lâminas de
corte.
1 Solte o grampo de liberação rápida (7) ao puxar para abrir completamente a alavanca de
liberação rápida (1).
2 Rode a alavanca de liberação rápida no sentido contrário aos ponteiros do relógio até
que a placa de fixação fique solta.
3 Coloque a lâmina de serra de instalação rápida, a placa de lixa ou a espátula na direção
ao fuso de saída que se encontra entre o grampo da tampa (9) e o grampo de liberação
rápida (7). Empurre o acessório para dentro e coloque-o firmemente nos pinos de
localização (8). Preste atenção para que a placa de fixação fique corretamente colocada
no suporte da máquina, caso contrário não poderá rodar a alavanca de liberação rápida.
4 Aperte a alavanca de liberação rápida (1), rode-a no sentido dos ponteiros do relógio
para apertar a placa de fixação e o acessório.
5 Verifique se a alavanca de liberação rápida está suficientemente apertada.
6 Pouse a alavanca de liberação rápida e rode-a até que se encontre por cima do suporte.
7 Empurre a alavanca de liberação rápida para o suporte.
8 Remova o acessório no sentido inverso.
AVISO: Esta ferramenta está equipada com acessórios para instalação
rápida durante a operação; não use acessórios inadequados.
AVISO: Verifique se a aplicação/acessório da ferramenta assenta
corretamente. Aplicações/acessórios incorretos ou apertados
incorretamente podem ficar soltos durante a operação e tornar-se perigo.
7.2 Colocar/mudar o papel de lixa
Com o engate rápido e o sistema de liberação rápida.
Posicione o papel de lixa e pressione manualmente.
Pressione o papel de lixa empurrando-o ligeiramente com firmeza contra a superfície
plana da placa de lixa (12) e ligue a ferramenta elétrica.
Isto garante uma boa aderência e evita o desgaste prematuro.
Se a ponta apresentar desgaste, retire o papel de lixa, rode-o 120º coloque-o novamente
ou mude o papel de lixa.
7.3 Montar a extração de pó (Fig. 4)
Remova o adaptador de pó (10) e aparafuse-o na parte inferior da máquina. Lembre-se que o
parafuso tem de estar na parte inferior do adaptador de pó, assim pode apertá-lo suavemente
no orifício do parafuso. Após montar esta peça na máquina, pode instalar o tubo de pó (11) no
adaptador de pó. Empurre firmemente o tubo. Pode sempre ajustar a direção do tubo ao
mover um pouco para a direção pretendida.

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results