PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC IT

Copyright © 2021 VARO P a g i n a | 8 www.varo.com
8.3.3 Levigatura
La capacità di asportazione e la micrografia vengono determinate essenzialmente dalla scelta
del foglio abrasivo, dal livello di numero di oscillazioni preselezionato e dalla pressione di
contatto.
Soltanto fogli abrasivi in perfetto stato possono garantire buone prestazioni abrasive e non
sottopongono l’elettroutensile a sforzi eccessivi.
Per aumentare la durata dei fogli abrasivi avere sempre cura di esercitare una pressione
uniforme.
Un eccessivo aumento della pressione esercitata non comporta una più alta prestazione
abrasiva ma provoca una maggiore usura dell’elettroutensile e del foglio abrasivo.
Per poter levigare con precisione angoli, spigoli e punti difficilmente accessibili è possibile
anche lavorare soltanto con la punta oppure con uno spigolo della piastra di levigatura.
In caso di levigatura di precisione, il foglio abrasive può riscaldarsi notevolmente. Ridurre il
numero di oscillazioni e lasciare raffreddare regolarmente il foglio abrasivo.
Una volta utilizzato un foglio abrasivo per la lavorazione del metallo non utilizzarlo più per altri
materiali.
8.3.4 Raschiatura
Per la raschiatura selezionare un alto livello di numero di oscillazioni. Lavorare su un fondo
morbido (p. es. legno) con un angolo piatto e con scarsa pressione di contatto. Altrimenti la
spatola può tagliare nel fondo.

9 PULIZIA E MANUTENZIONE

Prima di eseguire qualsiasi intervento sull'apparecchio staccare la spina.
Mantenere pulite le aperture di ventilazione della macchina per evitare il surriscaldamento
del motore.
Pulire regolarmente l’alloggiamento della macchina con un panno morbido, di preferenza
dopo ogni uso.
Mantenere le aperture di ventilazione libere da polvere e sporcizia.
Se la sporcizia non viene via usare un panno morbido inumidito con acqua saponata.
Non usare mai solventi come petrolio, alcol, ammoniaca, ecc. Questi solventi possono
danneggiare le parti di plastica.
Accertarsi che non penetri acqua all’interno dell’elettroutensile!

10 DATI TECNICI

Modello N.
POWX1347MC
Tensione
220-240 V
Frequenza
50 Hz
Potenza assorbita
300 W
Velocità in assenza di carico
15 000-22 000 min-1

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results