PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC DE

Copyright © 2021 VARO S e i t e | 8 www.varo.com
Vor dem Sägen mit einem Sägeblatt in Holz, Faserplatte, Baumaterial usw. immer das
Material auf verbliebene Fremdobjekte prüfen, wie z.B. Nägel, Schrauben usw. Solches
Material muss vor der Arbeit entfernt werden, oder es muss mit einem Metall-Sägeblatt
gearbeitet werden.
8.3.3 Schleifen
Die Abtragsleistung und das Schleifbild werden im Wesentlichen durch die Wahl des
Schleifpapiers, die eingestellte Geschwindigkeit und den Anpressdruck bestimmt.
Nur einwandfreies Schleifpapier erbringt eine gute Schleifleistung und schont das Gerät.
Achten Sie auf einen gleichmäßigen Anpressdruck, um die Lebensdauer des
Schleifpapiers zu erhöhen.
Eine übermäßige Erhöhung des Anpressdrucks führt nicht zu einer höheren
Schleifleistung, sondern zu stärkerem Verschleiß des Geräts und des Schleifpapiers.
Zum punktgenauen Schleifen von Ecken, Kanten und schwer zugänglichen Bereichen
können Sie auch nur mit der Spitze oder einer Kante der Schleifplatte arbeiten.
Beim punktuellen Schleifen kann sich das Schleifpapier stark erwärmen. Reduzieren Sie
die Schwingzahl, und lassen Sie das Schleifpapier regelmäßig abkühlen.
Benutzen Sie ein Schleifpapier, mit dem Metall bearbeitet wurde, nicht mehr für andere
Materialien.
8.3.4 Schaben
Wählen Sie beim Schaben eine hohe Geschwindigkeit.
Arbeiten Sie auf weichem Untergrund (z.B. Holz) in flachem Winkel und mit geringem
Anpressdruck. Der Schaber kann sonst in den Untergrund schneiden.

9 REINIGUNG UND WARTUNG

WARNHINWEIS: Vor allen Arbeiten am Gerät das Gerät immer von der
Stromversorgung trennen.
Halten Sie die Lüftungsschlitze des Geräts sauber, um eine Überhitzung des Motors zu
vermeiden.
Das Gehäuse des Geräts regelmäßig mit einem weichen Tuch reinigen, möglichst nach
jedem Einsatz.
Halten Sie die Lüftungsschlitze von Staub und Schmutz frei.
Wenn der Schmutz nicht abgeht, verwenden Sie bitte ein mit Seifenwasser befeuchtetes
weiches Tuch.
Lösemittel wie z.B. Benzin, Alkohol, Ammoniakwasser usw. nie benutzen! Diese
Lösemittel können die Kunststoffteile beschädigen.
WARNHINWEIS: Wasser darf auf keinen Fall in das Innere des Geräts
eindringen können!

10 TECHNISCHE DATEN

Modell Nr.
POWX1347MC
Spannung
220-240 V
Netzfrequenz
50 Hz
Stromaufnahme
300 W
Drehzahl ohne Last
15.000-22.000 U/Min.

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results