PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC EN

Copyright © 2021 VARO P a g e | 6 www.varo.com
Press on the sand paper by giving it a short, firm push against the flat surface of sanding
plate (12) and switch on the power tool.
This ensures good adhesion and prevents premature wear.
If the point has become worn, pull off the sand paper, turn it through 120º and place it on
again, or change the sanding paper.
7.3 Mounting dust extraction (Fig. 4)
Take the dust adaptor (10) and screw it on the bottom part of the machine. Keep in mind that
the screw has to be on the bottom part of the dust adaptor, this way you can screw it nice and
gently in the screw hole. After this piece is mounted on the machine, you can attach the dust
pipe (11) on the dust adaptor. Give the pipe a firm push. You can always adjust the direction
of the pipe by moving it a bit in the desired direction.

8 OPERATION

8.1 Switching ON/OFF (Fig. 5)
First check that the cable and plug are not damaged.
Connect the plug to the power supply.
Switching the power tool ON: slide ON/OFF switch button (2) forward onto position (I).
Switching the power tool OFF: slide ON/OFF switch button backward onto position (O).
8.2 Speed adjusting (Fig. 6)
The tool can be set at 6-speed adjustment positions. The "1" position indicates the lowest and
the "6" position indicates the highest speed, you can adjust different speed by turning the
speed control dial (4) from "1" to "6" position. The operator may have to vary the speed to
optimize working efficiency.
8.3 Application tips
8.3.1 Selecting the Application Tool/Accessory
Accessory (Fig 7)
Material
A: 3,2cm saw blade
Wooden materials, plastic, metal, gypsum and other
soft materials.
B: 6,5cm saw blade
Wooden materials, plastic, metal, gypsum and other
soft materials.
C: 2,0cm saw blade
Wooden materials, plastic, metal, gypsum and other
soft materials.
D: 1,0cm small saw blade
Wooden materials, plastic, metal, gypsum and other
soft materials.
E: 8,5cm Segment blade
Wooden materials, plastic, metal, gypsum and other
soft materials.
F: 5,2cm Scraping blade
Suitable for the removal of paint and carpet.
G: 9,3cm Carbide segment blade
Cuts grooves in drywall, plaster, lightweight concrete
and similar materials
H: 3,2cm Carbide blade
Cuts grooves in drywall, plaster, lightweight concrete
and similar materials
I: Triangular sanding pad
Sanding pad for 90x90x90 sized sanding papers.
J: Triangular sanding papers
Sanding papers in different grains:
120
180
240
K: Finger sanding pad
Sanding pad for finger sanding papers.
L: Finger sanding papers
Finger sanding papers in different grains:

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results