PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC EN

Copyright © 2021 VARO P a g e | 5 www.varo.com
Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held
more secure than by hand.
Do not use the machine when the quick release lever is not tightened.
Keep your workplace clean. Blends of materials are particularly dangerous. Dust from light
alloys can burn or explode.
Wear protective gloves when changing application tools/accessories.
Application tools/ accessories become hot after prolonged usage.
Do not scrape wetted materials (e. g. wallpaper) or on moist surfaces. Penetration of water
into the machine increases the risk of an electric shock.
Do not treat the surface to be worked with solvent-containing fluids. Materials being
warmed up by the scraping can cause toxic vapours to develop.
Exercise extreme caution when handling the scraper. The accessory is very sharp; danger
of injury.

7 ASSEMBLY

WARNING: Always check that the power supply corresponds to the voltage
on the rating name plate. Remove the power tool from the packaging. Do
not plug it into the electrical grid before assembly.
7.1 Mounting sanding plate/ saw blade/ spatula (Fig. 1)
WARNING: Prior to assembly and adjustment always pull out the power
plug from the mains socket.
Take care with sharp tools such as spatulas, saw blades or cutting blades.
1 Loosen the quick release clamp (7) by pulling the quick-release lever (1) completely
open.
2 Spin the quick release lever anti-clock wise until the clamping plate is lose.
3 Put the quick-install saw blade, sanding plate or spatula toward the output spindle which
is situated between the cover clamp (9) and quick release clamp (7). Push the accessory
in and place it firmly onto the locating pins (8). Pay attention that the clamping plate is
placed well into the holder of the machine, otherwise you cannot spin the quick release
lever.
4 Fasten using the quick-release lever (1), spin it in a clockwise direction to fasten the
clamping plate and accessory.
5 Check if the quick release lever is tightened enough.
6 Pull the quick release lever down and spin it until it is right above the holder.
7 Push the quick release lever into the holder.
8 Remove the accessory in the opposite way
WARNING: This tool is equipped with quick-install accessories during
operating; do not use any unmatched accessories.
WARNING: Check the tight seating of the application tool/accessory.
Incorrect or not securely fastened application tools/accessories can come
loose during operation and pose a hazard.
7.2 Mounting/changing the sand paper
With fast hook and quick release system.
Position the sand paper and press by hand.

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results