PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC FR

Copyright © 2021 VARO P a g e | 8 www.varo.com
Avant de scier avec des lames de scie du bois, des panneaux de particules, des matériaux de
construction, etc., vérifiez qu’aucun corps étranger tel que des clous, vis ou similaires n’est
présent. Si nécessaire, retirez les corps étrangers ou utilisez des lames de scie adaptées au
métal.
8.3.3 Le ponçage
La puissance d’enlèvement de matière ainsi que l’état de la surface dépendent en grande
partie du choix de la feuille abrasive, de la vitesse de rotation présélectionnée ainsi que de la
pression exercée sur l’appareil.
Seules des feuilles abrasives impeccables assurent un bon travail de ponçage et ménagent
l’outil électroportatif.
Veiller à ce que la pression de travail soit régulière, afin d’augmenter la durée de vie des
feuilles abrasives.
Une trop grande pression exercée sur l’appareil n’entraîne pas une meilleure puissance de
ponçage mais une usure plus importante de l’outil électroportatif et de la feuille abrasive.
Pour poncer avec une précision extrême des coins, des bords et des endroits d’accès difficile,
il est également possible de ne travailler qu’avec la pointe ou le bord du plateau de ponçage.
Lors du ponçage ponctuel, la feuille abrasive peut fortement chauffer. Réduisez alors la
vitesse et laissez la feuille abrasive régulièrement refroidir.
Une feuille abrasive avec laquelle on a travaillé du métal, ne doit pas être utilisée pour
d’autres matériaux.
8.3.4 Gratter
Choisissez une vitesse élevée pour le grattage.
Travaillez sur une surface souple (p.ex. bois) avec un angle plat et une pression minimale.
Sinon, le racloir peut couper dans la surface.

9 NETTOYAGE ET ENTRETIEN

Avant toute intervention sur l'appareil, débranchez la fiche du secteur.
Maintenez les fentes de ventilation propres afin d’éviter la surchauffe du moteur.
Nettoyez régulièrement le bâti de la machine avec un chiffon doux, de préférence après
chaque utilisation.
Maintenez les fentes de ventilation exemptes de poussière et de saleté.
Si la saleté est tenace, utilisez un chiffon doux mouillé avec de l’eau savonneuse.
N’utilisez jamais de solvants comme l’essence, l’alcool, l’ammoniaque, etc. Ces solvants
peuvent endommager les pièces en plastique.
Vérifiez que l’eau ne peut en aucun cas pénétrer à l’intérieur de l’outil
électrique !

10 DONNÉES TECHNIQUES

Modèle N.
POWX1347MC
Tension
220-240 V
Fréquence
50 Hz
Puissance
300 W
Vitesse à vide
15 000-22 000 min-1

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results