PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC SK

Copyright © 2021 VARO S t r a n a | 7 www.varo.com
prach (11) na adaptéri na prach. Rúrku riadne zatlačte. Vždy môžete upraviť smer rúrky tým,
že ňou trochu pohýbete v želanom smere.

8 PREVÁDZKA

8.1 Zapnutie / vypnutie (obr. 5)
Najprv skontrolujte, či elektrický kábel a zástrčka nie sú poškodené.
Zástrčku pripojte k napájaciemu zdroju.
Zapnutie elektrického náradia: Hlavný vypínač (2) posuňte dopredu do polohy (I).
Vypnutie elektrického náradia: Hlavný vypínač posuňte dozadu do polohy (O).
8.2 Nastavenie rýchlosti (obr. 6)
Rýchlosť náradia sa dá nastaviť v 6 nastavovacích polohách. Poloha „1“ označuje najnižšiu a
poloha „6“ označuje najvyššiu rýchlosť. Otáčaním regulátora rýchlosti (4) od polohy 1 do
polohy 6 môžete nastaviť inú rýchlosť. Operátor môže meniť rýchlosť, aby optimalizoval
efektívnosť práce.
8.3 Tipy pre použitie
8.3.1 Výber pracovného nástroja
Príslušenstvo (obr. 7)
Materiál
A: 3,2cm pílový list
Drevené materiály, plast, kov, sadra a iné mäkké
materiály.
B: 6,5cm pílový list
Drevené materiály, plast, kov, sadra a iné mäkké
materiály.
C: 2,0cm pílový list
Drevené materiály, plast, kov, sadra a iné mäk
materiály.
D: 1,0 pílový list
Drevené materiály, plast, kov, sadra a iné mäkké
materiály.
E: 8,5cm Segmentový list
Drevené materiály, plast, kov, sadra a iné mäkké
materiály.
F: 5,2cm Škrabkový list
Vhodný na odstraňovanie náteru a kobercov.
G: 9,3cm Karbidový segmentový list
Reže drážky do sadrokartónu, sadry, ľahkého betónu
a podobných materiálov
H: 3,2cm Karbidový list
Reže drážky do sadrokartónu, sadry, ľahkého betónu
a podobných materiálov

I : Trojuholníková brúsna podložka

Brúsna podložka pre brúsne papiere s rozmermi
90x90x90.
J: Trojuholníkové brúsne papiere
Brúsne papiere v rôznych zrnitostiach:
120
180
240
K: Prstová brúsna podložka
Brúsna podložka pre prstové brúsne papiere.
L: Prstové brúsne papiere
Prstové brúsne papiere v rôznych zrnitostiach:
120
180
240
8.3.2 Rezanie
Používajte len nepoškodené a bezchybné rezacie listy. Skrivené, neostré
alebo iným spôsobom poškodené rezacie listy sa môžu zlomiť.

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results