PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC CS

Copyright © 2021 VARO Stránka | 8 www.varo.com
8.2 Nastavení rychlosti (obr. 6)
Nástroj lze nastavit na 6 nastavitelných rychlostních pozic. Poloha "1" udává nejnižší a poloha
"6" udává nejvyšší rychlost; můžete nastavit jinou rychlost otáčením číselníku regulace otáček
(4) od polohy "1" po polohu "6". Může být třeba, aby pracovník obsluhy změnil rychlost za
účelem optimalizace účinnosti práce.
8.3 Praktické zkušenosti a tipy
8.3.1 Volba nasazovacího nástroje
Příslušenství (obr. 7)
Materiál
A: 3,2cm pilový kotouč
Dřevěné materiály, plast, kov, sádra a další
měkké materiály.
B: 6,5cm pilový kotouč
Dřevěné materiály, plast, kov, sádra a další
měkké materiály.
C: 2,0cm pilový kotouč
Dřevěné materiály, plast, kov, sádra a další
měkké materiály.
D: 1,0cm pilový kotouč
Dřevěné materiály, plast, kov, sádra a další
měkké materiály.
E: 8,5cm Segmentový kotouč
Dřevěné materiály, plast, kov, sádra a další
měkké materiály.
F: 5,2cm Škrabák
Vhodný pro odstraňování barev a koberců.
G: 9,3cm Kotouč s karbidovými segmenty
Dělené drážky v sádrokartonu, omítce, lehkém
betonu a podobných materiálech
H: 3,2cm Břitová destička
Dělené drážky v sádrokartonu, omítce, lehkém
betonu a podobných materiálech
I: Trojúhelníková brusná botka
Brusná deska pro brusný papír o rozměru
90x90x90.
J: Trojúhelníkové brusné papíry
Brusné papíry o různé zrnitosti:
120
180
240
K: Brusná botka prstového tvaru
Brusná botka pro prstové brusné papíry.
L: Prstové brusné papíry
Prstové brusné papíry o různé zrnitosti:
120
180
240
8.3.2 Řezání
Používejte pouze nepoškozené, bezvadné pilové listy. Zprohýbané, neostré
nebo jinak poškozené pilové listy se mohou zlomit.
Zapichovací řezy se používají pouze na měkké materiály jako dřevo,
sádrokarton apod.!
Než necháte pilové kotouče zaříznout se do dřeva, dřevotřískové desky, stavebních materiálů
atd., zkontrolujte, zda v nich nejsou cizí předměty, jako jsou hřebíky, šrouby, nebo podobné.
Pokud je to nutné, cizí předměty odstraňte nebo použijte pilové kotouče na kov.

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results