PowerPlus POWX1347MC manual

PowerPlus POWX1347MC
7.1 · 1
PDF manual
 · 232 pages
English
manualPowerPlus POWX1347MC

POWX1347MC CS

Copyright © 2021 VARO Stránka | 7 www.varo.com
Dávejte si pozor při práci s ostrými nástroji jako jsou lopatky, pilové kotouče nebo řezací
kotouče.
1 Uvolněte rychlosvorku (7) vytažením rychloupínací páčky (1) do zcela otevřené polohy.
2 Rychloupínací páčku otočte proti směru pohybu hodinových ručiček, dokud se upínací
deska neuvolní.
3 Posuňte rychloinstalační pilový kotouč, brusnou desku nebo stěrku směrem k
výstupnímu vřetenu, které se nachází mezi sponou víka (9) a rychloupínací svorkou (7).
Zatlačte na příslušenství a pevně je nasaďte na ustavovací čepy (8). Dohlédněte, aby se
upínací deska dobře usadila v držáku stroje, jinak nemůžete otáčet páčkou rychlého
uvolnění.
4 Upevněte páčkou rychlého uvolnění (1), otočte jí dovnitř ve směru pohybu hodinových
ručiček, abyste upevnili upínací desku a příslušenství.
5 Zkontrolujte, zda je dostatečně utažena páčka rychlého uvolnění.
6 Stáhněte páčku rychlého uvolnění dolů a otočte jí, dokud nebude přímo nad držákem.
7 Zatlačte páčku rychlého uvolnění do držáku.
8 Odstraňte příslušenství opačným směrem
VAROVÁNÍ: Tento nástroj je vybaven příslušenstvím rychle instalovatelným
za provozu; nepoužívejte žádné nesladěné příslušenství.
VAROVÁNÍ: Zkontrolujte pevné usazení aplikačního nástroje / příslušenství.
Nesprávné nebo ne dost bezpečně upevněné aplikační nástroje /
příslušenství se mohou uvolnit za provozu a představovat riziko.
7.2 Montáž / výměna brusného papíru
Se suchým zipem.
Položte brusný papír na místo a ručně jej přitlačte.
Přitlačte brusný papír tak, že na něj krátce a silně zatlačíte proti plochému povrchu brusné
desky (12); pak zapnete elektrické nářadí.
To zajišťuje dobrou přilnavost a zabraňuje předčasnému opotřebení.
Jestliže se tento bod opotřeboval, sejměte brusný papír, otočte jej o 120° a umístěte jej na
plochu znovu, nebo brusný papír vyměňte.
7.3 Montáž odsávání prachu (obr. 4)
Vezměte prachový nástavec (10) a našroubujte jej na dno stroje. Myslete na to, že šroub musí
být na dolní části prachového nástavce, takže ho můžete pěkně a s citem našroubovat do
příslušného otvoru. Po montáži tohoto dílu na stroj můžete k prachovému nástavci připevnit
prachovou trubici (11). Trubici nasuňte rázným pohybem. Směr trubice můžete vždycky
upravit tak, že ji o kousek posunete do požadovaného směru.

8 PROVOZ

8.1 Zapnutí / vypnutí (obr. 5)
Nejprve zkontrolujte, zda kabel a zástrčka nejsou poškozeny.
Připojte zástrčku do elektrické sítě.
Zapnutí elektrického nástroje: posuňte tlačítko hlavního vypínače (2) dopředu do polohy
(I).
Vypnutí elektrického nástroje: posuňte tlačítko hlavního vypínače (2) dozadu do polohy (I).

Manual

View the manual for the PowerPlus POWX1347MC here, for free. This manual comes under the category multi tools and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the PowerPlus POWX1347MC or do you need help? Ask your question here

Index

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus POWX1347MC specifications

Below you will find the product specifications and the manual specifications of the PowerPlus POWX1347MC.

General
BrandPowerPlus
ModelPOWX1347MC
Productmulti-tool
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus POWX1347MC below.

What is the best way to clean my saw blade?

1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.

My saw blade is blunt. What now?

If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

How do I mount the sanding plate, saw blade, or spatula on the PowerPlus POWX1347MC multi-tool?

1. Loosen the quick release clamp by pulling the quick-release lever completely open. 2. Spin the quick release lever counterclockwise until the clamping plate is loose. 3. Place the sanding plate, saw blade, or spatula towards the output spindle between the cover clamp and quick release clamp. Push the accessory in and firmly place it onto the locating pins. Ensure the clamping plate is well-placed into the holder. 4. Fasten the accessory by using the quick-release lever, spinning it clockwise to secure the clamping plate and accessory. 5. Verify that the quick release lever is tightened adequately. 6. Pull the quick release lever down and position it right above the holder. 7. Push the quick release lever into the holder to complete the mounting process.

How can I change the sandpaper on the PowerPlus POWX1347MC multi-tool?

To change the sandpaper on the PowerPlus POWX1347MC multi-tool, follow these steps: 1. Press the sandpaper firmly against the flat surface of the sanding plate. 2. Switch on the power tool to ensure good adhesion and prevent premature wear. 3. If the sandpaper becomes worn, pull it off, turn it through 120º, and place it back on or replace it. 4. Position the new sandpaper and press it by hand to secure it in place. Remember to always follow these steps carefully to maintain the effectiveness of your multi-tool.

Is the manual of the PowerPlus POWX1347MC available in English?

Yes, the manual of the PowerPlus POWX1347MC is available in English .

Is your question not listed? Ask your question here

No results