PowerPlus Dual Power POWDPSET11 manual

PowerPlus Dual Power POWDPSET11
5.8 · 1
PDF manual
 · 13 pages
English
manualPowerPlus Dual Power POWDPSET11

POWDP1520 EN

Copyright © 2018 VARO P a g e | 11 www.varo.com
Bend or burn bits
Produce off-center or irregular shaped holes
When drilling large holes in metal, it is recommended that you drill with a small bit at first, then
finish with a large bit. Also, lubricate the bit with oil to improve drilling action and increase bit
life.
10.4 Driving screw
For maximum performance, use good quality bits for driving screws , turn the function
mode selector on the screwdriver mode position21.
Fix the torque setting low enough to allow a safety margin. Use a very low torque setting
when first driving small screws into soft materials. Then adjust the setting as the proper
force required is determined.
NOTE: The torque setting required depends on the item being driven. In the
case of screws, consider the size, length, and type of material.
10.5 Hammer Setting
For maximum performance, use a good quality masonry bit for hammer drill, turn the
function mode selector on the impact mode position .
Only use this setting to bore or drill into stone/concrete. The Hammer setting works well
when drilling/chipping into materials.
The tip of tool MUST be firmly depressed for the hammer action to engage.
NOTE: Only use a masonry bit when drilling into masonry materials.

11 CLEANING AND MAINTENANCE

11.1 Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may
damage the plastic parts.
11.2 Maintenance
Our machines have been designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends upon proper machine care
and regular cleaning.

12 TECHNICAL DETAILS

Chuck
13 mm keyless
Power supply
20 Volt DC
Gear Train
2 Speed
No Load Speed
0-450/0-1700 min-1
Clutch
21+1+1 Positions
Torque
50Nm (MAX.)

13 NOISE

Noise emission values measured according to relevant standard. (K=3)

Manual

View the manual for the PowerPlus Dual Power POWDPSET11 here, for free. This manual comes under the category drill machines and has been rated by 1 people with an average of a 5.8. This manual is available in the following languages: English. Do you have a question about the PowerPlus Dual Power POWDPSET11 or do you need help? Ask your question here

Need help?

Do you have a question about the PowerPlus and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

PowerPlus Dual Power POWDPSET11 specifications

Below you will find the product specifications and the manual specifications of the PowerPlus Dual Power POWDPSET11.

General
BrandPowerPlus
ModelDual Power POWDPSET11
Productdrill machine
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the PowerPlus Dual Power POWDPSET11 below.

How do I remove rust from my PowerPlus drill machine?

1. Soak the rusty part in vinegar until completely soaked through. 2. Let the vinegar work on the rust for 24 hours. 3. Remove the rust with a wire brush or aluminium foil.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

Do I have to wear hearing protection when using a drill machine?

The amount of sound varies a lot per brand and type of drill machine, it is therefore wise to wear hearing protection to be sure.

Is the manual of the PowerPlus Dual Power POWDPSET11 available in English?

Yes, the manual of the PowerPlus Dual Power POWDPSET11 is available in English .

Is your question not listed? Ask your question here

No results