Poulan Pro PR675Y22RHP manual

Poulan Pro PR675Y22RHP
9.7 · 2
PDF manual
 · 60 pages
English
manualPoulan Pro PR675Y22RHP
a WARNING! Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury.

Instruction Manual

PR5020

Quick-Start Guide

NOTE: Your product may differ slightly from the item shown.
1
Mix 2.6 oz. of full synthetic 2-Cycle Oil with 1 gallon of fresh seasonal
gasoline for a 50:1 mixture. Shake well. Pour into fuel tank.
CAUTION: Do not use alternate fuels such as ethanol blends above
10% by volume (E-15, E-85) or any methanol blended fuel.
2
Add bar and chain oil to oil tank
until full.
3
Make sure chain brake is locked by
pushing forward on handguard.
4
Slowly press primer (air purge) bulb
10 times.
5
Pull blue choke lever out fully.
6
Place right foot in rear handle as shown.
Using right hand, pull starter rope sharply
until machine attempts to start, or a maximum
of 5 times.
7
Push blue choke lever to half choke
position.
8
Pull starter rope until engine starts.
9
Allow engine to warm for 30 seconds.
10
Make sure chain brake is unlocked by
pulling back on handguard.

11

Squeeze throttle trigger to set normal
idle. Your chainsaw is now ready
for use.
12
Press red switch to STOP position
ZKHQ¿QLVKHGXVLQJVDZ
STARTING A WARM ENGINE

4 + 5 + 7 + 8

NOTE: If the product does not restart, the problem could be overheated
IXHO7R¿[WKLVSUREOHPWU\WKHIROORZLQJSURFHGXUH
1. Set the product in a cool area away from direct sunlight.
2. Allow the product to cool for at least 20 minutes.
3. Press primer (air purge) bulb repeatedly for 10-15 seconds.
4. Follow the cold starting procedure.
Repeat this procedure if the problem still exists.
NOTE: Always use fresh seasonal fuel and shorten operation time
during unseasonably warm weather.
IMPORTANT:
Never let your saw chain come in contact with soil/dirt during
operation. This will completely dull your chain and will require
installation of a new chain.
Check your chain tension prior to each time you start the chainsaw.
&KHFNWHQVLRQRQDQHZFKDLQDIWHUWKH¿UVWPLQXWHVRI
operation. See the manual for chain tensioning instructions.
LDAV50MC115817295 Rev. D 2019-01-23

View the manual for the Poulan Pro PR675Y22RHP here, for free. This manual comes under the category lawnmowers and has been rated by 2 people with an average of a 9.7. This manual is available in the following languages: English. Do you have a question about the Poulan Pro PR675Y22RHP or do you need help? Ask your question here

Need help?

Do you have a question about the Poulan and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 2
K
Kelly WashburnApril 15, 2024

need a diagram to replace broken control cable

K
Kelly WashburnApril 15, 2024

diagram for replacing self propelled control cable

The Poulan Pro PR675Y22RHP is a lawnmower designed for residential use. It features a 6.75 horsepower Briggs & Stratton engine for reliable performance. The mower has a 22-inch cutting deck, allowing for efficient cutting of grass in medium to large-sized yards. It is equipped with high rear wheels for easy maneuverability over uneven terrain and around obstacles. The lawnmower has a 3-in-1 cutting system, which allows for bagging, mulching, or side discharge of grass clippings. Additionally, the Poulan Pro PR675Y22RHP has a variable speed front-wheel drive system, providing control over the mower's pace. The handle is adjustable to fit the user's height for comfortable operation. The lawnmower also features a foldable design for compact storage when not in use. Overall, the Poulan Pro PR675Y22RHP is a reliable and durable option for those looking to maintain their lawn with ease.

General
BrandPoulan
ModelPro PR675Y22RHP
Productlawnmower
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Poulan Pro PR675Y22RHP below.

How short should I cut the grass?

When the grass is longer than 4.5cm, the grass should be cut. The ideal length is between 3 and 4.5cm.

How often should I cut the grass?

In the spring, the grass should be cut every week, while in the summer once every two weeks is sufficient.

Can I mow the lawn when the grass is wet?

You can, but the result is better in dry weather. When the grass is wet, grass clumps can easily form and clog the mower.

How can I troubleshoot if the lawnmower is not cutting the limbs properly?

To troubleshoot if the Poulan Pro PR675Y22RHP lawnmower is not cutting the limbs properly, follow these steps: 1. Ensure the working area is free from obstructions such as other trees, branches, rocks, fences, or stumps. Remove any obstacles that the saw chain could hit while cutting. 2. Keep the guide bar and saw chain sharp and properly tensioned. A dull or loose chain can affect cutting performance. Follow the manufacturer's instructions for chain sharpening and maintenance. Check the chain tension regularly with the engine stopped and ensure the nuts are securely tightened after tensioning the chain. 3. Begin and continue cutting at full speed. If the chain is moving at a slower speed, there is a greater chance of kickback occurring. 4. Use wedges made of plastic or wood to hold the cut open. Never use metal, as it can damage the chain. 5. Cut one log at a time to maintain control and prevent kickback. 6. Avoid twisting the saw as the bar is withdrawn from an undercut when bucking. 7. Use a reduced-kickback guide bar and low-kickback chain designed for your saw to minimize the risk of kickback. 8. Maintain control of the saw by gripping it firmly with both hands. Keep your left hand on the front handlebar and your right hand on the rear handle. Stand with your weight evenly balanced on both feet. By following these troubleshooting steps, you can ensure that the lawnmower cuts limbs properly and safely.

What should I do if the lawnmower is not pruning the branches effectively?

To troubleshoot if the Poulan Pro PR675Y22RHP lawnmower is not pruning branches effectively, follow these steps: 1. Ensure the working area is clear of any obstacles such as other trees, branches, rocks, fences, or stumps. Remove any obstructions that could interfere with the pruning process. 2. Check the sharpness and tension of the saw chain. A dull or loose chain can affect the cutting performance. Follow the manufacturer's instructions for chain sharpening and tensioning. Make sure the chain is properly tensioned and sharp. 3. Start pruning at the base of the branch and work your way towards the end. Use smooth and steady cutting motions, allowing the saw to do the work. Avoid forcing the saw through the branches, as this can lead to ineffective pruning. 4. Use proper cutting techniques, such as making an undercut before making the final cut. This helps prevent the branch from splitting or tearing during the pruning process. 5. If the branches are thick or dense, consider using a reduced-kickback guide bar and low-kickback chain designed for your lawnmower. These specialized components can improve cutting efficiency and safety. 6. Regularly inspect the saw for any damage or worn parts. Contact an authorized service dealer if you notice any issues that may affect the pruning performance. By following these troubleshooting steps, you can ensure that the Poulan Pro PR675Y22RHP lawnmower effectively prunes branches.

What troubleshooting steps should I follow if the lawnmower is not starting or running smoothly?

To troubleshoot if the Poulan Pro PR675Y22RHP lawnmower is not starting or running smoothly, follow these steps: 1. Check if the ignition switch is off. Ensure that the switch is in the correct position for starting the lawnmower. 2. Verify that the fuel tank is not empty. If the tank is empty, fill it with the correct fuel. 3. Make sure the fuel is reaching the carburetor. Check for any clogs or blockages in the fuel line and clean or replace if necessary. 4. Inspect the spark plug. If the spark plug is fouled or worn, replace it with a new one. 5. Check if the chain brake is engaged. Disengage the chain brake to allow the lawnmower to accelerate properly. 6. Adjust the carburetor if necessary. Follow the manufacturer's instructions for carburetor adjustment to ensure proper idle speed and acceleration. 7. If the troubleshooting steps above do not resolve the issue, contact an authorized service dealer for further assistance. By following these troubleshooting steps, you can address starting and running issues with the Poulan Pro PR675Y22RHP lawnmower.

How can I troubleshoot if the lawnmower is not properly lubricating the bar?

To troubleshoot if the Poulan Pro PR675Y22RHP lawnmower is not properly lubricating the bar, follow these steps: 1. Check the oil reservoir to ensure it is filled with the appropriate bar and chain oil. If the oil level is low, refill it to the recommended level. 2. Inspect the oil delivery system for any clogs or blockages. Clean or replace any components that may be obstructing the oil flow. 3. Verify that the oil pump is functioning correctly. Start the lawnmower and observe if oil is being dispensed onto the bar. If not, the oil pump may need to be repaired or replaced. 4. Adjust the oil flow rate if necessary. Follow the manufacturer's instructions to adjust the oil flow to the desired level. 5. Clean the bar and chain regularly to remove any debris or buildup that may be affecting the oiling process. Use a brush or compressed air to clean the bar groove and oil holes. 6. If the troubleshooting steps above do not resolve the issue, contact an authorized service dealer for further assistance. By following these troubleshooting steps, you can ensure that the Poulan Pro PR675Y22RHP lawnmower properly lubricates the bar for optimal performance.

What should I do if I notice any damaged or worn parts while performing maintenance on the lawnmower?

If you notice any damaged or worn parts while performing maintenance on the Poulan Pro PR675Y22RHP lawnmower, follow these steps: 1. Stop using the lawnmower immediately if you notice any damaged or worn parts. Continuing to use the lawnmower with damaged or worn parts can lead to further damage or unsafe operation. 2. Identify the specific damaged or worn part. Inspect the lawnmower thoroughly to determine which part needs attention. 3. Contact an authorized service dealer for assistance. They will be able to provide guidance on the best course of action for repairing or replacing the damaged or worn part. 4. If the damaged or worn part is easily replaceable, follow the manufacturer's instructions for removing the old part and installing the new one. Ensure that you have the correct replacement part before proceeding. 5. If the damaged or worn part requires professional repair, take the lawnmower to an authorized service dealer. They have the expertise and tools necessary to properly repair the lawnmower. By following these steps, you can address any damaged or worn parts on the Poulan Pro PR675Y22RHP lawnmower and ensure its safe and efficient operation.

Is the manual of the Poulan Pro PR675Y22RHP available in English?

Yes, the manual of the Poulan Pro PR675Y22RHP is available in English .

Is your question not listed? Ask your question here

No results