- 9 - - 10 - - 11 - - 12 - - 13 - Switch
100 meters
PoE
Power
Data
PoE PTZ
IP Camera
Ultra PoE Injector
Power
Data
AC
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
Power Line (AC)
AC
Figure 2: Connection to IEEE 802.3at/802.3af Powered
Devices
1. Connect the AC power cord to “AC slot” of Ultra P oE
Injector; the “POWER” LED will be on steadily .
2. Connect a standard network cable from switch/work-
station to “LAN” port of Ultra P oE Injector .
3. Connect the long cable to the port (PoE) of the
remote PoE PD device.
4. Connect with IEEE 802.3at/af devices.
Once Ultra P oE Injector detects the existence of an IEEE
802.3at/802.3af device, the ACTIVE LED indicator will
be on steadily to show it is providing power .
Note
If the connected device is not fully
complying with IEEE 802.3at/802.3af Power
over Ethernet or in-line power device, the
LED indicator of Ultra P oE Injector will not
be on steadily .
5-3 The Ultra PoE Injector and Splitter Installation Below are the steps showing how to install PLANET
Ultra P oE Injector (POE-172 & POE-173) and Ultra P oE
Splitter (POE-171S) in pair .
Switch
Power 12V/19V/24V
POE-171S
100 meters
Power
Data
Power
Data
PoE
Power
Data
AC
DC
Laptop
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
Power Line (AC)
AC
DC
Power Line (DC)
Ultra PoE Injector
Ultra PoE
Splitter
Figure 3: T opology of the Connection of Ultra PoE Injector and
POE-171S
1. Connect the AC power cord to “AC slot” of Ultra P oE
Injector; the “POWER” LED will be on steadily .
2. Connect a standard network cable from “POE” port
of Ultra P oE Injector to “PoE In” port of POE-171S.
The “ACTIVE” LED of Ultra PoE Injector and POE-in-
use LED of POE-171S will light up continuously .
3. Connect a standard network cable from switch/work-
station to “LAN” port of Ultra P oE Injector .
4. Connect the UTP cable in the package from
“Ethernet” port of POE-171S to the RJ45 port of
remote device.
5. Adjust proper DC power output and connect DC plug
from “DC OUT” of POE-171S to remote device.
6. Power on the remote device and its power LED indi-
cator will remain on.
Note
Please make sure the POE-171S output
voltage is correct before applying power
to remote device. The POE-171S provides
DC12V/19V/24V power output.
5-4 The Ultra PoE Injector and PoE Extender Installation Below are the steps showing how to install the PLANET
Ultra P oE Injector (POE-172 & POE-173) and 802.3at
PoE Plus Extender (POE-E201) to extend the distance of
networking.
802.3at
PoE Extender
Data
PoE PoE
+
Power
Power
Data +
Power
Data
100 meters100 meters
200 meters
Power Line (AC)
AC
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
PoE IP Camera
Ultra PoE Injector
Figure 4: T opology of the Connection of Ultra PoE Injector and
POE-E201
1. Connect the AC power cord to “AC slot” of Ultra P oE
Injector; the “POWER” LED will be on steadily .
2. Connect a standard network cable from “POE” port
of Ultra P oE Injector to the “IN” port of POE-E201.
3. The Ultra P oE Injector delivers both Ethernet Data
and PoE power ov er UTP cable to the POE-E201 and
the “ACTIVE” LED of Ultra P oE Injector and “PoE
IN” LED of POE-E201 will light up continuously .
4. Connect the additional standard network cable to the
remote Powered Device (PD) via the “OUT” port
of POE-E201.
5. The “OUT” port is also the power injector which
transmits DC voltage to the standard network cable
and transfer data and power simultaneously between
the Ultra P oE Injector and PD.
6. Once POE-E201 detects the existence of an IEEE
802.3at/802.3af device, the “PoE OUT” LED indi-
cator will be on steadily to show it is providing power .
Note
1. If the connected device is not fully
complying with IEEE 802.3at/802.3af
standard or in-line power device, the
PoE OUT LED indicator of POE-E201 will
not be on steadily .
2. According to IEEE 802.3at/802.3af
standard, the POE-E201 will not inject
power to the cable if not connected to a
standard IEEE 802.3at/802.3af device.
Customer Support Thank you for purchasing PLANET products. Y ou can
browse our online F AQ resource at the PLANET W eb site
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online F AQ :
http://www.planet.com.tw/en/support/faq.php?type=2
Switch support team mail address :
support_switch@planet.com.tw
Copyright © PLANET T echnology Corp. 2016
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANE T T echnology Corp. All
other trademarks belong to their respective owners.
EC Declaration of Conformity
For the following equipment:
*T ype of Product : Single-Port 10/100/1000Mbps Ultra PoE Injector
*Model Number : POE-173, POE-172
* Produced by:
Manufacturer‘s Name : Planet T echnology Corp.
Manufacturer‘s Address : 10F ., No.96, Minquan Rd., Xindian Dist.,
New T aipei City 231, T aiwan (R.O.C.).
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on 2004/108/EC and 2014/30/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN55022 (2010+AC:2011)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2006+A1:2007+A2:2010)
IEC 61000-4-4 (2012)
IEC 61000-4-5 (2006)
IEC 61000-4-6 (2013)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)
Responsible for marking this declar ation if the:
Manufacturer Authoriz ed representative established within the EU
Authorized representative e stablished within the EU (if applicable):
Company Name: Planet T echnology Corp.
Company Address: 10F. , No.96, Minquan Rd., Xindian Dist., New T aipei City 231, T aiwan
(R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Titl e : Dir ector
T a iwan 27
th
May, 2016
Place Date Legal Signature
PLANET TECHNOLOGY CORPORA TION
e-mail: sales@planet.com.tw http://www .planet.com.tw
10F ., No.96, Minquan Rd. , Xindian Dist., New T aipei City, T aiwan, R.O.C. T el:886-2-2219-9518 Fax:886-2-2219-9528
Need help?
Do you have a question about the Planet and is the answer not in the manual?
Question and answer
Number of questions: 0