- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents Thank you for purchasing PLANET Industrial 2-port Multi-Gigabit
802.3bt PoE++ Injector Hub
following sections, the term “Industrial PoE++ Injector Hub”
means the IPOE-270 or IPOE-270-12V
Open the box of the Industrial P
unpack it. The box should contain the following items:
Industrial PoE++ Injector Hub x 1 User’s Manual x 1
DIN-rail Kit x 1 RJ45 Dust Caps x 4 W
If any of these are missing or damaged, please contact your dealer
immediately
Power
Consumption
(Ethernet Full
Loading)
52V DC:
1.5watts/5.1B
54V DC:
1.6watts/5.4B
56V DC:
1.6watts/5.4B
Full loading with PoE
48V DC (120W PoE
Budget):
128watts/436B
52V DC (180W PoE
Budget):
177watts/603B
54V DC (180W PoE
Budget):
187watts/638B
56V DC (180W
PoE Budget):
185watts/631B
54V DC: 2.1watts/7.1B
56V DC: 2.2watts/7.5B
Full loading with PoE
12V DC (60W PoE Budget):
60watts/204B
24V DC (120W PoE Budget):
124watts/423B
48V DC (120W PoE Budget):
120watts/409B
52V DC (180W PoE Budget):
188watts/641B
54V DC (180W PoE Budget):
188watts/641B
56V DC (180W PoE Budget):
184watts/627B
Dimensions 41 x 70 x 115 mm (W x D x H)
W 284g 387g
Enclosure IP30 metal case
Installation DIN-rail kit and wall-mount kit
ESD Protection 6KV
Surge Protection 6KV
Power ov
PoE Standard
IEEE 802.3bt Power ov
PSE
Compatible with IEEE 802.3at PoE+ PSE
3.2 Device Upper Panel The upper panels of the Industrial PoE++ Injector Hubs consist of
one terminal block connector within two power inputs.
1 2 3 4
V1+
V2+
PWR1
PWR2
DC Input:
48-56V
, 4A max.
V1+
PWR1
V2+ V2
PWR2
DC Input:
12-56V
, 6A max.
1 2 3 4
Figure 3: IPOE-270 T Figure 4: IPOE-270-12V T
3.3 Wiring the Power Inputs The terminal block connector on the top panel of Industrial PoE++
Injector Hub is used for two DC redundant power inputs. Please
follow the steps below to insert the power wire.
Caution
When performing any of the procedures like inserting
the wires or tightening the wire-clamp screws, make
sure the power is OFF to prevent from getting an
electric shock.
1.
2 for POWER 1, or contacts 3 and 4 for POWER 2.
1 2 3 4
V1+
V2+
PWR1
PWR2
DC Input:
48-56V
, 4A max.
V1+
PWR1
V2+ V2
PWR2
DC Input:
12-56V
, 6A max.
1 2 3 4
3. Hardware Introduction 3.1 Device Front Panel The front panels of the Industrial PoE++ Injector Hubs consist of
Ethernet interfaces and LED indicators.
Front View P1 P2
60W 120W 180W
PoE
Usage
PoE++
Ethernet
PoE++
Ethernet
IPOE-270
P1 P2
60W 120W 180W
PoE
Usage
PoE++
Ethernet
PoE++
Ethernet
IPOE-270-12V
Data port 1
PoE port 1
Data port 2
PoE port 2
Figure 1: Figure 2:
IPOE-270 Front View IPOE-270-12V Front View
2. Model IPOE-270 IPOE-270-12V
Hardware
Copper Ports
2-pair 10/100/1G/2.5G/5GBASE-
Data input port 1 and PoE output port 1
Data input port 2 and PoE output port 2
Connector
Remov
Pins 1 and 2 for Power 1; Pins 3 and 4 for P
LED Indicator
System: Power 1 (Green) P
PoE Usage: 60W/120W/180W (Amber)
802.3bt PoE++ P PoE-in-use x 1 (Green:bt,
Amber:at)
Network Cable
T
10BASE-
100BASE-
1000BASE-
2.5G/5GBASE-
Data Rate 10/100/1000/2500/5000Mbps
Power
Requirements
48~56V DC,
redundant power
with reverse polarity
protection.
12~56V DC,
redundant power with
reverse polarity protection.
Power
Consumption
(Ethernet Full
Loading)
System ON without
loading
48V DC:
1.4watts/4.7B
System ON without
loading
12V DC: 1.8watts/6.1B
24V DC: 2.4watts/8.1B
48V DC: 2.4watts/8.1B
52V DC: 2.6watts/8.8B
PoE P
Supply T
End-span + Mid-span
Power Pin
Assignment
End-span: 1/2 (-), 3/6 (+); Mid-span: 4/5 (+), 7/8
(-)
PoE P
Budget (max.)
120W@48V DC input
180W@52V/54V/56V
DC input
60W@12V DC input
120W@24V/48V DC input
180W@52V/54V/56V DC
input
Number of
devices that can
be powered
2
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Stability T
IEC 60068-2-32 (free fall)
IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u F
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3bz 2.5G/5GBASE-
IEEE 802.3at Power ov
IEEE 802.3bt Power ov
Environment
T
Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity
Operating: 5~90% (non-condensing)
Storage: 5~90% (non-condensing)
System LEDs LED Color Function
P1 Green
Lights to indicate DC power input 1 has
power
P2 Green
Lights to indicate DC power input 2 has
power
PoE Usage Amber
60W, 120W, 180W
Lights to indicate the system consumes over
60-/120-/180-watt P
Blinks to indicate the system consumes less
60-/120-/180-watt P
802.3bt PoE++ TP Interface LEDs LED Color Function
802.3bt
PoE++
PoE-in-Use
Green
Lights to indicate that the port is providing
802.3bt PoE++ power to remote powered
device.
O
providing PoE power to remote powered
device.
Amber
Lights to indicate that the port is providing
802.3at PoE+ power to remote powered
device.
O
providing PoE power to remote powered
device.
2.
loosening.
1 2 3 4
Power 1 Power 2
+ - + -
Note
The wire gauge for the terminal block should be in the
range between 12 and 24 A
3.4 Grounding the Device Users MUST complete grounding wired with the device; otherw
a sudden lightning could cause fatal damage to the device.
1 2 3 4
V1+
V2+
PWR1
PWR2
DC Input:
48-56V
, 4A max.
Earth Ground
Note
EMD (Lightning) DAMAGE IS NOT CONVERED UNDER
WARRANTY
Need help?
Do you have a question about the Planet and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Planet owners to provide you with a good answer.
Number of questions: 0