Pioneer VSX-924 manual

Pioneer VSX-924
6.9 · 4
PDF manual
 · 121 pages
English
manualPioneer VSX-924
110
Additional information
14
If the subwoofer must be installed near a wall, place it at an angle so that it is not parallel to the wall surface. This
can help reduce any sympathetic vibrations, but depending on the shape of the room this could result in stand-
ing waves. However, even if standing waves are generated, their influence on the sound quality can be prevented
using the Auto MCACC’s standing wave control function (page 83 ).
Step 5: Default settings with the Auto MCACC Setup (auto sound field
correction) function
It is more effective to perform the Full Auto MCACC Setup (page 37 ) procedure once the adjustments described
above have been completed.
Note
The distance to the subwoofer may be slightly larger than the distance actually measured with a tape measure,
etc. This is because this distance is corrected for electric delay, and is not a problem.
Positional relationship between speakers and monitor
Position of front speakers and monitor
The front speakers should be as equidistant as possible to the monitor.
L
R
45° to 60°
Position of center speaker and monitor
Since mostly dialogs are output from the center speaker, keeping the center speaker as close as possible to the
screen makes the overall sound more natural. For TVs using Braun tubes, however, when installing the center
speaker on the floor, adjust its angle of elevation to point it towards the listening position.
Installation on floor
(Diagram as seen
from the side)
Monitor
! If the center speaker is not of the shielded type, install it away from the TV.
! When installing the center speaker on top of the monitor, place it facing slightly downwards towards the listen-
ing position.

About messages displayed when using network functions

Refer to the following information when you come up with a status message while operating the Network functions.
Status messages Descriptions
Connection Down
The selected category or Internet radio station cannot be accessed.
File Format Error
Cannot be played back for some reasons.
Track Not Found
The selected song has not been found anywhere on the network.
Server Error
The selected server cannot be accessed.
Server Disconnected
The server has been disconnected.
Empty
There are no files stored in the selected folder.
License Error
The license for the contents to be played back is invalid.
Item Already Exists
This is displayed when the file you have attempted to register in the Favorites folder has
already been registered.
Favorite List Full
This is displayed when you have attempted to register a file in the Favorites folder but the
Favorites folder is already full.

Important information regarding the HDMI connection

There are cases where you may not be able to route HDMI signals through this receiver (this depends on
the HDMI-equipped component you are connecting-check with the manufacturer for HDMI compatibility
information).
If you aren’t receiving HDMI signals properly through this receiver (from your component), please try one of the
following configurations when connecting up.
Configuration A
Use component video cables to connect the video output of your HDMI-equipped component to the receiver’s
component video input. The receiver can then convert the analog component video signal to a digital HDMI sig-
nal for transmission to the display. For this configuration, use the most convenient connection (digital is recom-
mended) for sending audio to the receiver. See the operating instructions for more on audio connections.
Note
The picture quality will change slightly during conversion.
Configuration B
Connect your HDMI-equipped component directly to the display using an HDMI cable. Then use the most conve-
nient connection (digital is recommended) for sending audio to the receiver. See the operating instructions for
more on audio connections. Set the display volume to minimum when using this configuration.
Notes
! If your display only has one HDMI terminal, you can only receive HDMI video from the connected component.
! Depending on the component, audio output may be limited to the number of channels available from the
connected display unit (for example audio output is reduced to 2 channels for a monitor with stereo audio
limitations).
! If you want to switch the input function, you’ll have to switch functions on both the receiver and your display
unit.
! Since the sound is muted on the display when using the HDMI connection, you must adjust the volume on the
display every time you switch input functions.
 

 

 

 

View the manual for the Pioneer VSX-924 here, for free. This manual comes under the category receivers and has been rated by 4 people with an average of a 6.9. This manual is available in the following languages: English. Do you have a question about the Pioneer VSX-924 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 2
M
Mar ViloriaJuly 31, 2022

My unit model Pioneer A/V Receiver VSX-924 can not be switch on through remote control. The red light indicator of ADVANCED MCACC keep on flashing. Kindly send advise what to do for this matter. Thanks

D
DebbieJanuary 22, 2016

I can't get my iPhone to pick up Bluetooth from the amp

The Pioneer VSX-924 is a receiver with 7.2 audio output channels, providing a multi-dimensional surround sound experience. It delivers high fidelity audio, with a low Total Harmonic Distortion (THD) of 1%, resulting in crisp and clear sound reproduction. The receiver has an input sensitivity of 315 mV, allowing it to effortlessly connect to various audio sources. It is equipped with multiple connectivity options, including HDMI in ports, composite video in ports, and digital audio optical and coaxial in ports. This allows for easy integration with a wide range of devices, such as televisions, gaming consoles, and audio players. With an output impedance of 6 Ω, the Pioneer VSX-924 ensures stable and reliable signal transmission to connected speakers. The receiver also boasts a high Signal-to-Noise Ratio (SNR) of 100 dB, minimizing any unwanted background noise and enhancing audio clarity. Additionally, this receiver features a pre-out connectivity option, enabling users to connect external amplifiers for an even more powerful sound experience. The Pioneer VSX-924 is designed to enhance the overall audio quality and create an immersive home theater environment. With its sleek design and intuitive user interface, the Pioneer VSX-924 is easy to set up and use. Its solid construction and premium materials ensure durability and longevity. This receiver is an ideal choice for anyone seeking a high-quality audio solution for their home entertainment system.

General
BrandPioneer
ModelVSX-924 | VSX-924-K
Productreceiver
EAN4988028244100
LanguageEnglish
FiletypeUser manual (PDF)
Audio
Power output per channel (20-20KHz@8 Ohm)- W
Audio output channels7.2 channels
Total Harmonic Distortion (THD)1 %
Input sensitivity315 mV
Input impedance47000 Ω
Output impedance6 Ω
Audio D/A Converter (DAC)24-bit/192kHz
Audio A/D Converter (ADC)24-bit/96kHz
Signal-to-Noise Ratio (SNR)100 dB
Pre-out connectivityYes
Receiver typeSurround
Power output per channel (1KHz@8 Ohm)105 W
Power output per channel (1KHz@6 Ohm)150 W
Inputs
HDMI in7
Composite video in2
Digital audio optical in1
Digital audio coaxial in1
Remote (IR) input1
Line-inYes
Ethernet LAN (RJ-45) ports1
USB ports quantity2
AC (power) inYes
Component video (YPbPr/YCbCr) in1
Outputs
Number of HDMI outputs2
Audio (L/R) out2
Remote (IR) output1
Headphone outputs1
Headphone connectivity3.5 mm
Line-outYes
Multichannel audio output typeRCA
Ports & interfaces
Speakers connectivity typeRCA
Connectivity technologyWired & Wireless
Multichannel pre out connectivityRCA
File formats
Audio formats supportedAAC, AIFF, FLAC, MP3, WAV, WMA
Network
Ethernet LANYes
Wi-FiYes
BluetoothYes
Wi-Fi readyYes
Radio
Supported radio bandsAM, FM
Internet radioYes
Internet radio services supportedSpotify, vTuner
Radio Data System (RDS)Yes
Preset stations quantity63
Optical drive
Optical drive includedNo
Storage
Card reader integratedNo
Video
Supported video modes1080i, 1080p, 480p, 720p
3DYes
Video upscalingYes
Technical details
DisplayLED
Audio decodersDolby Pro Logic IIz, Dolby TrueHD, DTS Neo:X, DTS-HD Master Audio
x.v.Color supportYes
Deep color supportYes
EqualizerYes
Mobile High-Definition Link (MHL)Yes
Bass adjustmentYes
Treble adjustmentYes
Graphical user interface (GUI)Yes
Graphical user interface (GUI) languageDutch, English, French, German, Italian, Russian, Spanish
Handheld remote controlYes
Product colorBlack
Audio amplifierYes
Sleep timerYes
Volume controlRotary
Apple docking compatibility-
Surround modes quantity12
AirPlayYes
Quantity1
Sample rate24 kHz
Auto standbyYes
Yes
Power
AC input voltage220-230 V
AC input frequency50 - 60 Hz
Power consumption (typical)550 W
Power consumption (standby)0.1 W
Weight & dimensions
Width435 mm
Depth362.5 mm
Height168 mm
Weight9800 g
Other features
Compatible operating systemsWindows 8.1
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer VSX-924 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is the weight of the Pioneer VSX-924?

The Pioneer VSX-924 has a weight of 9800 g.

What is the height of the Pioneer VSX-924?

The Pioneer VSX-924 has a height of 168 mm.

What is the width of the Pioneer VSX-924?

The Pioneer VSX-924 has a width of 435 mm.

What is the depth of the Pioneer VSX-924?

The Pioneer VSX-924 has a depth of 362.5 mm.

How do I connect my speakers to the Pioneer VSX-924 receiver?

Make sure to use the appropriate speaker cables and connect them to the corresponding speaker terminals on the back of the receiver, ensuring a secure connection.

What is the optimal placement for my receiver in my entertainment setup?

It is recommended to place the Pioneer VSX-924 receiver in a well-ventilated area with ample space around it to avoid overheating. Avoid placing it in enclosed spaces or near heat-emitting devices.

How can I adjust the audio settings on the receiver to enhance my listening experience?

Navigate to the audio settings menu on the receiver's interface, where you can fine-tune various parameters such as equalizer settings, sound mode selection, dialogue enhancement, and bass/treble adjustments to suit your preferences.

How can I connect my external devices (e.g., DVD player, gaming console) to the receiver?

Utilize the available HDMI, optical, or coaxial inputs on the Pioneer VSX-924 receiver to connect your external devices. Ensure that the input source on the receiver matches the corresponding input you are using for your device.

Can I set up a multi-room audio system with the Pioneer VSX-924 receiver?

Yes, the receiver supports multi-room audio functionality. Refer to the receiver's menu options to configure the multi-room settings, allowing you to play audio in different rooms simultaneously or independently using compatible speakers.

How many audio output channels does the Pioneer VSX-924 have?

The Pioneer VSX-924 has 7.2 audio output channels. This means it can support a surround sound setup with multiple speakers, providing an immersive audio experience for the user.

What is the Total Harmonic Distortion (THD) of the Pioneer VSX-924?

The THD of the Pioneer VSX-924 is 1%. This indicates that the receiver produces relatively low distortion in the audio output, resulting in cleaner and more accurate sound reproduction.

What is the input sensitivity of the Pioneer VSX-924?

The input sensitivity of the Pioneer VSX-924 is 315 mV. This means it requires a moderate input signal level to produce an optimal audio output.

Does the Pioneer VSX-924 have pre-out connectivity?

Yes, the Pioneer VSX-924 has pre-out connectivity. This allows users to connect additional power amplifiers or subwoofers, enabling greater flexibility in their audio setup.

How many HDMI inputs does the Pioneer VSX-924 have?

The Pioneer VSX-924 has 7 HDMI inputs. This is a generous amount of HDMI inputs, allowing users to connect multiple devices such as gaming consoles, media players, and Blu-ray players easily.

Is the manual of the Pioneer VSX-924 available in English?

Yes, the manual of the Pioneer VSX-924 is available in English .

Is your question not listed? Ask your question here

No results