Pioneer VSX-924 manual

Pioneer VSX-924
6.9 · 4
PDF manual
 · 121 pages
English
manualPioneer VSX-924
102
FAQ
13

USB interface

Symptom Cause Remedy
The folders/files stored on a
USB memory device are not
displayed.
The folders/files are currently stored
in a region other than the FAT (File
Allocation Table) region.
Store the folders/files in the FAT region.
The number of levels in a folder is
more than 9.
Limit the maximum number of levels in a folder to 9 (page
45 ).
The audio files are copyrighted.
Copyrighted audio files stored on a USB memory device
cannot be played back (page 45 ).
A USB memory device is
not recognized.
The USB memory device does not
support the mass storage class
specifications.
Try using a USB memory device compatible with the mass
storage class specifications. Note that there are cases
where even the audio files stored on a USB memory device
compatible with the mass storage class specifications are
not played back on this receiver (page 45 ).
Connect the USB memory device and switch on this
receiver (page 32 ).
A USB hub is currently being used.
This receiver does not support USB hubs (page 45 ).
This receiver recognizes the USB
memory device as a fraud.
Switch off and on again this receiver.
Reconnect the USB device with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
A USB memory device is
connected and displayed,
but the audio files stored
on the USB memory device
cannot be played back.
Some formats of USB memory
devices, including FAT 12, NTFS, and
HFS, cannot be played back on this
receiver.
Check whether the format of your USB memory device is
either FAT 16 or FAT 32. Note that the FAT 12, NTFS, and
HFS formats cannot be played back on this receiver (page
45 ).
The file format cannot be properly
played back on this receiver.
See the list of file formats that can be played back on this
receiver (page 46 ).
The USB memory cannot be
operated with the remote
control.
Press iPod USB to set the remote control to the iPod USB
control mode.
Over Current shows in the
display.
There is a problem with the power supply for the USB
memory. After turning off the receiver, disconnect the USB
memory, connect the USB memory again and then turn on
the power of the receiver.
If Over Current is displayed even though the above opera-
tion is repeated several times, there is a problem with the
receiver or USB memory. Disconnect the power cable and
request repair.
iPod
Symptom Cause Remedy
iPod is not recognized. This receiver recognizes the iPod as
a fraud.
Switch off and on again this receiver.
Reconnect the iPod with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
iPod touch/iPhone is not
recognized or otherwise
does not operate properly.
The iPod’s operation may be
unstable.
Try performing the operation below.
1. Press the sleep/sleep cancel button on the iPod touch/
iPhone simultaneously with the home button for at least 10
seconds to restart the device.
2. Turn this receiver’s power on.
3. Connect the iPod touch/iPhone to this receiver.
iPod cannot be operated
with the remote control.
Press iPod USB to set the remote control to the iPod USB
control mode.

Network

Symptom Cause Remedy
Cannot access the network. The LAN cable is not firmly con-
nected.
Firmly connect the LAN cable (page 31 ).
The router is not switched on. Switch on the router.
Internet security software is cur-
rently installed in the connected
component.
There are cases where a component with Internet security
software installed cannot be accessed.
The audio component on the net-
work which has been switched off is
switched on.
Switch on the audio component on the network before
switching on this receiver.
Playback does not start
while “Connecting...” con-
tinues to be displayed.
The component is currently discon-
nected from this receiver or the
power supply.
Check whether the component is properly connected to
this receiver or the power supply.
The network function can-
not be operated with the
remote control.
Press NET to set the remote control to the network function
control mode.
The PC or Internet radio is
not properly operated.
The corresponding IP address is not
properly set.
Switch on the built-in DHCP server function of your router,
or set up the network manually according to your network
environment (page 89 ).
The IP address is being automati-
cally configured.
The automatic configuration process takes time. Please
wait.
 

 

 

 

View the manual for the Pioneer VSX-924 here, for free. This manual comes under the category receivers and has been rated by 4 people with an average of a 6.9. This manual is available in the following languages: English. Do you have a question about the Pioneer VSX-924 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 2
M
Mar ViloriaJuly 31, 2022

My unit model Pioneer A/V Receiver VSX-924 can not be switch on through remote control. The red light indicator of ADVANCED MCACC keep on flashing. Kindly send advise what to do for this matter. Thanks

D
DebbieJanuary 22, 2016

I can't get my iPhone to pick up Bluetooth from the amp

The Pioneer VSX-924 is a receiver with 7.2 audio output channels, providing a multi-dimensional surround sound experience. It delivers high fidelity audio, with a low Total Harmonic Distortion (THD) of 1%, resulting in crisp and clear sound reproduction. The receiver has an input sensitivity of 315 mV, allowing it to effortlessly connect to various audio sources. It is equipped with multiple connectivity options, including HDMI in ports, composite video in ports, and digital audio optical and coaxial in ports. This allows for easy integration with a wide range of devices, such as televisions, gaming consoles, and audio players. With an output impedance of 6 Ω, the Pioneer VSX-924 ensures stable and reliable signal transmission to connected speakers. The receiver also boasts a high Signal-to-Noise Ratio (SNR) of 100 dB, minimizing any unwanted background noise and enhancing audio clarity. Additionally, this receiver features a pre-out connectivity option, enabling users to connect external amplifiers for an even more powerful sound experience. The Pioneer VSX-924 is designed to enhance the overall audio quality and create an immersive home theater environment. With its sleek design and intuitive user interface, the Pioneer VSX-924 is easy to set up and use. Its solid construction and premium materials ensure durability and longevity. This receiver is an ideal choice for anyone seeking a high-quality audio solution for their home entertainment system.

General
BrandPioneer
ModelVSX-924 | VSX-924-K
Productreceiver
EAN4988028244100
LanguageEnglish
FiletypeUser manual (PDF)
Audio
Power output per channel (20-20KHz@8 Ohm)- W
Audio output channels7.2 channels
Total Harmonic Distortion (THD)1 %
Input sensitivity315 mV
Input impedance47000 Ω
Output impedance6 Ω
Audio D/A Converter (DAC)24-bit/192kHz
Audio A/D Converter (ADC)24-bit/96kHz
Signal-to-Noise Ratio (SNR)100 dB
Pre-out connectivityYes
Receiver typeSurround
Power output per channel (1KHz@8 Ohm)105 W
Power output per channel (1KHz@6 Ohm)150 W
Inputs
HDMI in7
Composite video in2
Digital audio optical in1
Digital audio coaxial in1
Remote (IR) input1
Line-inYes
Ethernet LAN (RJ-45) ports1
USB ports quantity2
AC (power) inYes
Component video (YPbPr/YCbCr) in1
Outputs
Number of HDMI outputs2
Audio (L/R) out2
Remote (IR) output1
Headphone outputs1
Headphone connectivity3.5 mm
Line-outYes
Multichannel audio output typeRCA
Ports & interfaces
Speakers connectivity typeRCA
Connectivity technologyWired & Wireless
Multichannel pre out connectivityRCA
File formats
Audio formats supportedAAC, AIFF, FLAC, MP3, WAV, WMA
Network
Ethernet LANYes
Wi-FiYes
BluetoothYes
Wi-Fi readyYes
Radio
Supported radio bandsAM, FM
Internet radioYes
Internet radio services supportedSpotify, vTuner
Radio Data System (RDS)Yes
Preset stations quantity63
Optical drive
Optical drive includedNo
Storage
Card reader integratedNo
Video
Supported video modes1080i, 1080p, 480p, 720p
3DYes
Video upscalingYes
Technical details
DisplayLED
Audio decodersDolby Pro Logic IIz, Dolby TrueHD, DTS Neo:X, DTS-HD Master Audio
x.v.Color supportYes
Deep color supportYes
EqualizerYes
Mobile High-Definition Link (MHL)Yes
Bass adjustmentYes
Treble adjustmentYes
Graphical user interface (GUI)Yes
Graphical user interface (GUI) languageDutch, English, French, German, Italian, Russian, Spanish
Handheld remote controlYes
Product colorBlack
Audio amplifierYes
Sleep timerYes
Volume controlRotary
Apple docking compatibility-
Surround modes quantity12
AirPlayYes
Quantity1
Sample rate24 kHz
Auto standbyYes
Yes
Power
AC input voltage220-230 V
AC input frequency50 - 60 Hz
Power consumption (typical)550 W
Power consumption (standby)0.1 W
Weight & dimensions
Width435 mm
Depth362.5 mm
Height168 mm
Weight9800 g
Other features
Compatible operating systemsWindows 8.1
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer VSX-924 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is the weight of the Pioneer VSX-924?

The Pioneer VSX-924 has a weight of 9800 g.

What is the height of the Pioneer VSX-924?

The Pioneer VSX-924 has a height of 168 mm.

What is the width of the Pioneer VSX-924?

The Pioneer VSX-924 has a width of 435 mm.

What is the depth of the Pioneer VSX-924?

The Pioneer VSX-924 has a depth of 362.5 mm.

How do I connect my speakers to the Pioneer VSX-924 receiver?

Make sure to use the appropriate speaker cables and connect them to the corresponding speaker terminals on the back of the receiver, ensuring a secure connection.

What is the optimal placement for my receiver in my entertainment setup?

It is recommended to place the Pioneer VSX-924 receiver in a well-ventilated area with ample space around it to avoid overheating. Avoid placing it in enclosed spaces or near heat-emitting devices.

How can I adjust the audio settings on the receiver to enhance my listening experience?

Navigate to the audio settings menu on the receiver's interface, where you can fine-tune various parameters such as equalizer settings, sound mode selection, dialogue enhancement, and bass/treble adjustments to suit your preferences.

How can I connect my external devices (e.g., DVD player, gaming console) to the receiver?

Utilize the available HDMI, optical, or coaxial inputs on the Pioneer VSX-924 receiver to connect your external devices. Ensure that the input source on the receiver matches the corresponding input you are using for your device.

Can I set up a multi-room audio system with the Pioneer VSX-924 receiver?

Yes, the receiver supports multi-room audio functionality. Refer to the receiver's menu options to configure the multi-room settings, allowing you to play audio in different rooms simultaneously or independently using compatible speakers.

How many audio output channels does the Pioneer VSX-924 have?

The Pioneer VSX-924 has 7.2 audio output channels. This means it can support a surround sound setup with multiple speakers, providing an immersive audio experience for the user.

What is the Total Harmonic Distortion (THD) of the Pioneer VSX-924?

The THD of the Pioneer VSX-924 is 1%. This indicates that the receiver produces relatively low distortion in the audio output, resulting in cleaner and more accurate sound reproduction.

What is the input sensitivity of the Pioneer VSX-924?

The input sensitivity of the Pioneer VSX-924 is 315 mV. This means it requires a moderate input signal level to produce an optimal audio output.

Does the Pioneer VSX-924 have pre-out connectivity?

Yes, the Pioneer VSX-924 has pre-out connectivity. This allows users to connect additional power amplifiers or subwoofers, enabling greater flexibility in their audio setup.

How many HDMI inputs does the Pioneer VSX-924 have?

The Pioneer VSX-924 has 7 HDMI inputs. This is a generous amount of HDMI inputs, allowing users to connect multiple devices such as gaming consoles, media players, and Blu-ray players easily.

Is the manual of the Pioneer VSX-924 available in English?

Yes, the manual of the Pioneer VSX-924 is available in English .

Is your question not listed? Ask your question here

No results