Pioneer VSX-830 manual

Pioneer VSX-830
7.8 · 3
PDF manual
 · 142 pages
English
manualPioneer VSX-830
115
FAQ
14
Symptom Remedy
Excluding VSX-830: No sound from
surround back speakers.
Check that the surround back speakers are set to LARGE or SMALL, and the surround
speakers are not set to NO (see Speaker Setting on page 107 ).
Check the speaker connections (see Connecting the speakers on page 23 ). If only
one surround back speaker is connected, make sure it’s connected to the left channel
speaker terminal.
When Speaker System is set to 7.2ch/5.2.2ch and SP: TMd ON is selected with the
OUT P. button, no sound will be output from the surround back speakers. Select SP:
SB ON or SP: SB/TMd ON (see Switching the speaker terminals on page 88 ).
When Speaker System is set to 7.2ch SB/FW and SP: FW ON is selected with the OUT P.
button, no sound will be output from the surround back speakers. Select SP: SB ON or
SP: SB/FW ON (see Switching the speaker terminals on page 88 ).
When Dolby Surround is selected, audio is not output from the surround back speaker
when it is the only one connected (set).
Excluding VSX-830: No sound from
front wide speakers.
Check that the front wide speakers are set to LARGE or SMALL, and the surround speak-
ers are not set to NO (see Speaker Setting on page 107 ).
Check the speaker connections (see Connecting the speakers on page 23 ).
When Speaker System is set to 7.2ch SB/FW and SP: SB ON is selected with the OUT P.
button, no sound will be output from the front wide speakers. Select SP: FW ON or SP:
SB/FW ON (see Switching the speaker terminals on page 88 ).
When Speaker System is set to 7.2ch SB/FW and Dolby Surround is selected, audio is
not output from the front wide speakers.
No sound from subwoofer. Check that the subwoofer is connected properly, switched on and the volume turned up.
If your subwoofer has a sleep function, make sure it is switched off.
Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 107 ).
The crossover frequency may be set too low; try setting it higher to match the characteris-
tics of your other speakers (see Speaker Setting on page 107 ).
If there is very little low frequency information in the source material, change your
speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(see Speaker Setting on page 107 ).
Check that the LFE channel is not set to OFF, or to a very quiet setting (see Setting the
Audio options on page 85 ).
Check the speaker level settings (see Channel Level on page 108 ).
No sound from one speaker.
Check the speaker connection (see Connecting the speakers on page 23 ).
Check the speaker level settings (see Channel Level on page 108 ).
Check that the speaker hasn’t been set to NO (see Speaker Setting on page 107 ).
The channel may not be recorded in the source. By using one of the advanced effect
listening modes, you may be able to create the missing channel (see Enjoying various
types of playback using the listening modes on page 71 ).
No digital sound is output.
Make sure that the digital input is assigned correctly for the input jack the component is
connected to (see The Input Setup menu on page 59 ).
Check the digital output settings on the source component.

Other audio problems

Symptom Remedy
Broadcast stations cannot be
selected automatically, or there is
considerable noise in radio broad-
casts.
Fully extend the FM wire antenna, adjust the position for best reception and secure to a
wall, etc.
Use an outdoor antenna for better reception (see pages 31 , 45 ).
Adjust the position and direction of the AM antenna.
Noise may be caused by interference from other equipment, such as a fluorescent light,
motor, etc. Switch off or move the other equipment, or move the AM antenna.
Subwoofer output is very low.
To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL
(see Speaker Setting on page 107 ).
Everything seems to be set up cor-
rectly, but the playback sound is odd.
The speakers may be out of phase. Check that the positive/negative speaker terminals on
the receiver are matched with the corresponding terminals on the speakers (see Con-
necting the speakers on page 23 ).
The Phase Control feature doesn’t
seem to have an audible effect.
If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass
cutoff is set to the highest frequency setting. If there is a PHASE setting on your sub-
woofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the
best overall effect on the sound).
Make sure the speaker distance setting is correct for all speakers (see Speaker Distance
on page 108 ).
Can’t select some Input functions
by the INPUT SELECTOR on the
front panel or the ALL button on the
remote control.
Check the Input Skip settings in the Input Setup menu (see The Input Setup menu on
page 59 ).
Check the HDMI Input assignment in the Input Setup menu then try OFF (see The Input
Setup menu on page 59 ).
There seems to be a time lag
between the speakers and the output
of the subwoofer.
See Automatically conducting optimum sound tuning (Full Auto MCACC) on page 57
to set up your system again using MCACC (this will automatically compensate for a delay
in the subwoofer output).
The maximum volume available
(shown in the front panel display) is
lower than the +12dB maximum.
Check that the Volume Limit is set to OFF (see Volume Setup on page 109 ).
The channel level setting may be over 0.0dB.
Certain listening modes or
HOME MENU items cannot be
selected.
Some functions cannot be selected, depending on the input signal and listening mode.
The volume level drops automati-
cally.
The temperature within the unit has exceeded the allowable value. Try moving the unit for
better ventilation (see Installing the receiver on page 10 ).
Volume seems different when input
is switched.
Set the Channel Level setting to ALL, then adjust the volume of the respective input
sources (see Input Volume Absorber on page 89 ).
Excluding VSX-830: When HDZONE is
ON, multi-channel audio sources are
not output in the main zone.
When HDZONE is selected in Speaker System and also the same HDMI input is selected
for both the main zone and HDZONE, 2-channel PCM audio sources are output from the
main zone as well. To output multi-channel audio sources, set HDZONE to OFF or change
the HDZONE input.
Excluding VSX-830: No HDZONE
sound is output.
With HDZONE, multi-channel audio may not be output. In this case, set the audio output
setting of your playback device to 2-channel PCM.
 

 

 

 

View the manual for the Pioneer VSX-830 here, for free. This manual comes under the category receivers and has been rated by 3 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Pioneer VSX-830 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 3
C
Chris January 22, 2023

How do I configure my receiver with a firestick device? I tried pairing the firestick directly to my tv first but I’m getting no sound just picture. Thanks.

A
Alan December 24, 2023

Model vsx830. FL light is flashing. Can not turn amp on

R
Rose BrooksApril 11, 2024

Will VSX-830 carry two Klipsçh speakers

The Pioneer VSX-830 is a receiver designed for home entertainment systems. It offers a range of features that enhance audio and video experiences. With its sleek design, this receiver adds a touch of modernity to any setup. Equipped with advanced technologies, the Pioneer VSX-830 delivers high-quality sound reproduction. It supports both Dolby TrueHD and DTS-HD Master audio formats, ensuring immersive and accurate audio playback. The receiver also features advanced digital-to-analog conversion, resulting in precise and dynamic sound. In terms of connectivity options, the VSX-830 offers a variety of inputs and outputs. It includes multiple HDMI inputs, allowing seamless connection to various devices such as Blu-ray players, gaming consoles, and set-top boxes. The receiver also supports 4K Ultra HD pass-through, ensuring compatibility with the latest video formats. The VSX-830 supports wireless connectivity through built-in Wi-Fi and Bluetooth. This enables easy streaming and playback from compatible devices, providing convenience and flexibility for users. With its intuitive interface and user-friendly remote control, operating the VSX-830 is straightforward. The receiver also supports smartphone control, allowing users to adjust settings and playback options conveniently. Overall, the Pioneer VSX-830 receiver is a versatile and reliable option for home entertainment enthusiasts. Combining cutting-edge technology with ease of use, this receiver elevates the audio and video experience, making it a worthwhile addition to any home theater setup.

General
BrandPioneer
ModelVSX-830
Productreceiver
LanguageEnglish
FiletypeUser manual (PDF), Datasheet (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer VSX-830 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

How do I connect my speakers to the Pioneer VSX-830 receiver?

Ensure that the speaker wires are properly inserted into the corresponding speaker terminals on the back of the receiver, making sure to match the polarity (+ and -).

How can I adjust the audio settings on the Pioneer VSX-830?

Access the on-screen menu, navigate to the "Audio" settings, and you can adjust various parameters including equalizer settings, channel levels, and sound modes.

How do I set up my TV with the Pioneer VSX-830 receiver?

Connect an HDMI cable from the HDMI OUT (ARC) port on the receiver to the HDMI ARC port on your TV. Then, ensure the TV's HDMI ARC setting is enabled, allowing audio to be sent from the TV to the receiver.

What should I do if there is no sound coming out of my speakers connected to the Pioneer VSX-830?

Check that the speaker wires are securely connected and that the speakers are powered on. Additionally, ensure the receiver is not on a muted mode and the correct input source is selected.

How can I optimize the audio performance of the Pioneer VSX-830 for my specific room?

The receiver offers automatic speaker calibration called "MCACC." Activate this feature, place the included microphone in your seating position, and follow the on-screen instructions to allow the receiver to analyze your room and automatically adjust the audio settings accordingly.

Is the manual of the Pioneer VSX-830 available in English?

Yes, the manual of the Pioneer VSX-830 is available in English .

Is your question not listed? Ask your question here

No results