Pioneer VSX-527 manual

Pioneer VSX-527
8 · 21
PDF manual
 · 68 pages
English
manualPioneer VSX-527
10
Chapter
10
62

Additional information

Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Take a look at the other components and electrical appliances being used, because sometimes the problem may lie there. If the trouble isn’t sorted out even after going through the checks below, ask your nearest Pioneer authorized independent service company to carry out repair work.
If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.
General
The power does not turn on.
Disconnect the power plug from the outlet, and insert again.
Make sure there are no loose strands of speaker wire touching
the rear panel. This could cause the receiver to shut off
automatically.
The receiver suddenly switches off.
When the Auto Power Down function is working, the power will
automatically turn off if the receiver has not operated for
several hours. Check the setting for the Auto Power Down
function (see The Auto Power Down menu on page 52).
After about a minute (you won’t be able to switch the unit on
during this time), switch the receiver back on. If the message
persists, call a Pioneer authorized independent service
company.
The power suddenly turns on or off, or the input suddenly
changes (When the Control with HDMI is ON).
This happens because of the synchronized operation due to
the Control with HDMI function. If synchronized operations
are not needed, set the Control with HDMI to OFF (see HDMI
Setup on page 53).
OVERHEAT shows in the display and the power turns off.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (page 2).
Lower the volume level.
TEMP shows in the display and the volume level drops.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (page 2).
Lower the volume level.
No sound is output when an input function is selected.
Use
VOLUME +/–
to turn up the volume.
Press
MUTE
on the remote control to turn muting off.
Press
SPEAKERS
to select the proper speaker set (see
Switching the speaker terminal on page 14).
Set the
SIGNAL SEL
to H (HDMI), C1/O1 (digital) or A (analog)
according to the type of connections made (page 25).
Make sure the component is connected correctly (refer to
Connecting your equipment on page 11).
Check the audio output settings of the source component.
Refer to the instruction manual supplied with the source
component.
No image is output when an input function is selected.
Make sure the component is connected correctly (refer to
Connecting your equipment on page 11).
VSX-527 only: Use the same type of video cables for the source
component and TV to connect to this receiver (see About video
outputs connection (VSX-527 only) on page 16).
VSX-827 only: Check The Input Assign menu on page 50 to
make sure you’re assigned the correct input.
The video input selected on the TV monitor is incorrect. Refer
to the instruction manual supplied with the TV.
VSX-827 only: For HDMI, or when Video Converter is set to OFF
and a TV and another component are connected with different
cords (in Video Converter on page 50), you must connect your
TV to this receiver using the same type of video cable as you
used to connect your video component.
VSX-827 only: Some components (such as video game units)
have resolutions that may not be converted. If adjusting this
receiver’s Resolution setting (in Resolution on page 51) and/or
the resolution settings on your component or display doesn’t
work, try switching Video Converter (in Video Converter on
page 50) OFF.
No sound from subwoofer.
Make sure the subwoofer is switched on.
If the subwoofer has a volume knob, make sure it’s turned up.
The Dolby Digital or DTS source you are listening to may not
have an LFE channel.
Switch the subwoofer setting in Speaker Setting on page 47 to
YES or PLUS.
Switch the LFE ATT (LFE Attenuate) on page 37 to LFEATT 0 or
LFEATT 5.
No sound from surround or center speakers.
Connect the speakers properly (page 12).
Refer to Speaker Setting on page 47 to check the speaker
settings.
Refer to Channel Level on page 49 to check the speaker levels.
The OSD screen (Home Menu, etc.) isn’t displayed.
The OSD will not appear if you have connected using the
composite output to your TV. Use HDMI connection when
setting up the system.
The Phase Control feature doesn’t seem to have an
audible effect.
If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest
frequency setting. If there is a PHASE setting on your
subwoofer, set it to 0º (or depending on the subwoofer, the
setting where you think it has the best overall effect on the
sound).
Make sure the speaker distance setting is correct for all
speakers (see Speaker Distance on page 49).
Considerable noise in radio broadcasts.
Connect the antenna (page 21) and adjust the position for best
reception.
Route any loose cables away from the antenna terminals and
wires.
Fully extend the FM wire antenna, position for best reception,
and secure to a wall (or connect an outdoor FM antenna).
Connect an additional internal or external AM antenna
(page 21).
Turn off equipment causing interference or move it away from
the receiver (or move antennas farther away from equipment
causing noise).
Broadcast stations cannot be selected automatically.
Connect an outdoor antenna (page 21).
Noise during playback of a cassette deck.
Move the cassette deck away from your receiver, until the noise
disappears.
No sound is output or a noise is output when software
with DTS is played back.
Make sure the player’s settings are correct and/or the DTS
signal out is on. Refer to the instruction manual supplied with
the DVD player.
There seems to be a time lag between the speakers and
the output of the subwoofer.
See Automatically setting up for surround sound (MCACC) on
page 23 to set up your system again using MCACC (this will
automatically compensate for a delay in the subwoofer output).

View the manual for the Pioneer VSX-527 here, for free. This manual comes under the category receivers and has been rated by 21 people with an average of a 8. This manual is available in the following languages: English. Do you have a question about the Pioneer VSX-527 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 6
L
LubosJune 9, 2022

Dobrý den, nejde mi na dálkovém ovladači zvyšovat či snižovat hlasitost u vsx-527. prosím o radu. děkuji

B
BudimirMarch 2, 2023

How to connect turntable with av receiver Pioneer 525.Whic port is for connection with turntable. Thank you.

R
Richard April 12, 2015

Hello, can you please forward a PDF copy of the Pioneer VSX-527 to the above email address. Thankyou, Richard

F
fredOctober 1, 2022

can i connect a turntable to this amp? if so, how???

N
N.pooleNovember 13, 2017

How do I switch on dots 5.1 surround sound

G
GOH MAY FERNFebruary 29, 2024

do pioneer vsx 527 suuport hdmi arc?

The Pioneer VSX-527 is a receiver that offers a range of features to enhance the audio experience. It is designed to deliver clear and balanced sound quality, providing an immersive listening experience. The receiver supports various audio formats, including Dolby Digital and DTS, allowing for a realistic and dynamic surround sound experience. It also has a built-in amplifier, providing sufficient power for a wide range of speakers. With multiple HDMI inputs, the Pioneer VSX-527 allows for easy connectivity of various devices, such as Blu-ray players and gaming consoles. It also features an HDMI output, enabling seamless connection to a compatible TV or projector. The receiver offers a user-friendly interface, allowing for easy navigation and control. It features an intuitive remote control, ensuring convenient operation from a distance. Additionally, it is equipped with an on-screen display, providing clear and informative visuals. The Pioneer VSX-527 includes advanced audio calibration technology, enabling automatic speaker setup and optimization. This ensures optimal audio performance in any listening environment. Moreover, the receiver offers support for multi-zone audio, allowing for the distribution of audio throughout the house. This feature enables users to enjoy music in multiple rooms, providing a seamless and synchronized audio experience. Overall, the Pioneer VSX-527 is a feature-rich receiver that delivers high-quality audio performance and offers convenient connectivity options. It is a reliable and durable choice for those seeking an enhanced home audio experience.

General
BrandPioneer
ModelVSX-527
Productreceiver
EAN4988028163579, 4988028181078
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer VSX-527 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

How do I connect my Pioneer VSX-527 receiver to my TV?

Ensure you have an HDMI cable, then connect one end to the HDMI output on the receiver and the other end to the HDMI input on your TV. Make sure to select the corresponding HDMI input on your TV for audio and video playback.

What is the optimal speaker setup for my Pioneer VSX-527?

For an ideal surround sound experience, position your speakers in a 5.1-channel configuration. Place two front speakers at equal distances from the TV, a center speaker above or below the TV, two surround speakers to your sides, and a subwoofer for deep bass near the front speakers.

How can I adjust the bass and treble settings on my Pioneer VSX-527?

To adjust the audio characteristics, go to the receiver's menu, select the "Sound" or "Audio" option, and then look for the "Tone Control" settings. From there, you can fine-tune the bass and treble levels to match your preferences.

Why is there no sound coming from my Pioneer VSX-527 receiver?

First, make sure your speakers are properly connected to the receiver. Then, verify that the receiver is set to the correct audio input and that the volume is turned up. Additionally, ensure that no mute function is activated and that the speaker wires are not damaged or disconnected.

How can I set up and use the built-in radio tuner on my Pioneer VSX-527?

To set up the radio tuner, connect the FM antenna to the dedicated FM antenna port on the back of the receiver. Then, press the "Tuner" button on the receiver's remote control to access the radio mode. Use the channel buttons or the tuning knob to search for and select your desired radio stations.

Is the manual of the Pioneer VSX-527 available in English?

Yes, the manual of the Pioneer VSX-527 is available in English .

Is your question not listed? Ask your question here

No results