Pioneer VSX-522 manual

Pioneer VSX-522
8.4 · 22
PDF manual
 · 39 pages
English
manualPioneer VSX-522
7
7
35
Chapter

Additional information

Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Take a look at the other components and electrical appliances being used, because sometimes the problem may lie there. If the trouble isn’t sorted out even after going through the checks below, ask your nearest Pioneer authorized independent service company to carry out repair work.
If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.
General
The power does not turn on.
Disconnect the power plug from the outlet, and insert again.
Make sure there are no loose strands of speaker wire touching
the rear panel. This could cause the receiver to shut off
automatically.
The receiver suddenly switches off.
When the Auto Power Down function is working, the power will
automatically turn off if the receiver has not operated for
several hours. Check the setting for the Auto Power Down
function (see The Auto Power Down menu on page 33).
After about a minute (you won’t be able to switch the unit on
during this time), switch the receiver back on. If the message
persists, call a Pioneer authorized independent service
company.
Power automatically turns ON/OFF and the input switches
from one to another. (When the ARC function is ON)
The CEC (Consumer Electronic Control) function may activate
when the ARC function is turned ON, causing power to turn
ON and OFF and the input to switch from one to another. Since
this unit does not guarantee synchronized operation based on
the CEC function, turn OFF the HDMI CONTROL setting on the
connected player. Refer to the relevant device’s instruction
manual for details.
If this does not work, turn OFF the ARC function. If this is the
case, listen to the TV audio after connecting this unit and the
TV with an audio cable.
OVERHEAT shows in the display and the power turns off.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (page 2).
Lower the volume level.
TEMP shows in the display and the volume level drops.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (page 2).
Lower the volume level.
No sound is output when an input function is selected.
Use
VOLUME +/–
to turn up the volume.
Press
MUTE
on the remote control to turn muting off.
Set the
SIGNAL SEL
to H (HDMI), C1/O1 (digital) or A (analog)
according to the type of connections made (page 20).
Make sure the component is connected correctly (see
Connecting your equipment on page 10).
Check the audio output settings of the source component.
Refer to the instruction manual supplied with the source
component.
No image is output when an input function is selected.
Make sure the component is connected correctly (see
Connecting your equipment on page 10).
Use the same type of video cables for the source component
and TV to connect to this receiver (see About video outputs
connection on page 13).
The video input selected on the TV monitor is incorrect. Refer
to the instruction manual supplied with the TV.
No sound from subwoofer.
Make sure the subwoofer is switched on.
If the subwoofer has a volume knob, make sure it’s turned up.
The Dolby Digital or DTS source you are listening to may not
have an LFE channel.
Switch the subwoofer setting in Speaker Setting on page 30 to
YES or PLUS.
Switch the LFE ATT (LFE Attenuate) on page 28 to LFEATT 0 or
LFEATT 5.
No sound from surround or center speakers.
Connect the speakers properly (page 11).
Refer to Speaker Setting on page 30 to check the speaker
settings.
Refer to Channel Level on page 31 to check the speaker levels.
The Phase Control feature doesn’t seem to have an
audible effect.
If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest
frequency setting. If there is a PHASE setting on your
subwoofer, set it to 0º (or depending on the subwoofer, the
setting where you think it has the best overall effect on the
sound).
Make sure the speaker distance setting is correct for all
speakers (see Speaker Distance on page 32).
Considerable noise in radio broadcasts.
Connect the antenna (page 16) and adjust the position for best
reception.
Route any loose cables away from the antenna terminals and
wires.
Fully extend the FM wire antenna, position for best reception,
and secure to a wall (or connect an outdoor FM antenna).
Connect an additional internal or external AM antenna
(page 16).
Turn off equipment causing interference or move it away from
the receiver (or move antennas farther away from equipment
causing noise).
Broadcast stations cannot be selected automatically.
Connect an outdoor antenna (page 16).
Noise during playback of a cassette deck.
Move the cassette deck away from your receiver, until the noise
disappears.
No sound is output or a noise is output when software
with DTS is played back.
Make sure the player’s settings are correct and/or the DTS
signal out is on. Refer to the instruction manual supplied with
the DVD player.
There seems to be a time lag between the speakers and
the output of the subwoofer.
See Automatically setting up for surround sound (MCACC) on
page 18 to set up your system again using MCACC (this will
automatically compensate for a delay in the subwoofer output).
After using the Auto MCACC setup, the speaker size
setting (LARGE or SMALL) is incorrect.
Low-frequency noise could have been caused by an air
conditioner or motor. Switch off all appliances in the room and
rerun the Auto MCACC setup.
Can’t operate the remote control.
Replace the batteries (page 9).
Operate within 7 m (23 ft.), 30º of the remote sensor (page 9).
Remove the obstacle or operate from another position.
Avoid exposing the remote sensor on the front panel to direct
light.
The display is dark or off.
Press
DIMMER
on the remote control repeatedly to return to
the default.

View the manual for the Pioneer VSX-522 here, for free. This manual comes under the category receivers and has been rated by 22 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Pioneer VSX-522 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 22
D
Diego diaz tunOctober 16, 2022

My equipment completely turned off, it is a Pioneer receiver VSX-522, can someone tell me how to unlock it by pressing a button that should not have turned it off and it does not turn on, friends or in any other way that I could do?

My equipment completely turned off, it is a Pioneer receiver VSX-522, can someone tell me how to unlock it by pressing a butt...
zoom-in
View photo
This message has been automatically translated
A
Alden KisonJanuary 10, 2024

No sound comes out from the speakers when using a wireless mic, setting on sat/cable A or or 01. How do I troubleshoot?

No sound comes out from the speakers when using a wireless mic, setting on sat/cable A or or 01.  How do I troubleshoot?
zoom-in
View photo
1 comment
E
Emma of manua.lsFebruary 13, 2024

To resolve the problem of no sound coming out from the speakers when using a wireless mic with the Pioneer VSX-522 receiver, you can try the following steps: 1. Check the connections: Make sure the wireless mic is properly connected to the receiver. Ensure that the cables are securely plugged in and there are no loose connections. 2. Verify the input settings: Confirm that the input source on the receiver is set to "sat/cable A" or "01" for the wireless mic. Use the input selector on the receiver or remote control to switch to the correct input. 3. Check the volume levels: Ensure that the volume level for the wireless mic input is not set to zero or muted. Use the volume control on the receiver or remote control to increase the volume. 4. Test with another audio source: Connect a different audio source, like a DVD player or smartphone, to the receiver and check if there is sound output. This will help determine if the issue is specific to the wireless mic or a general audio problem. 5. Reset the receiver: If the above steps do not solve the issue, try resetting the receiver.

This answer is automatically generated
D
Dan hammond October 28, 2023

Want to Mate my Pioneer Be able to pick up Bluetooth. Go to USX 522 K What do you recommend? What's your savor I'm Bluetooth for safer, that is to use.

Want to Mate my Pioneer Be able to pick up Bluetooth. Go to USX 522 K What do you recommend? What's your savor I'm Bluetooth ...
zoom-in
View photo
C
CaseyApril 19, 2022

Why does my pioneer vsx 522 play like a skipping c d and is there a specific way it has to be hooked up before it will play

J
joe spedusMarch 15, 2023

have this unit and 6 speakers 2 driven from accessory amp. how do i connect and place my 4 new atmos speakers for a 7.1.4 configuration

A
Alden KisonJanuary 10, 2024

Can i use this as a karaoke machine if i connect a wireless mic and playing you tube karaoke on sat/cable setting. No sound (vocals)comes out from the speakers

Can i use this as a karaoke machine if i connect a wireless mic and playing you tube karaoke on sat/cable setting.  No sound ...
zoom-in
View photo
T
Terry October 19, 2023

How do I connect my VSX 522 to my smart TV to play streaming shows through my speakers?

V
VuyaniApril 22, 2024

What causes no sound out of speakers when Dolby pro Logic and Dts is selected

J
John E LewisNovember 12, 2021

How do I play songs from my cell phone through this system?

M
Manasseh ArhinJuly 16, 2022

why is it that the sound doesn't come apart from pure direct option select

The Pioneer VSX-522 is a receiver designed for audio enthusiasts. With its sleek and modern design, it seamlessly integrates into any home theater setup. This receiver is equipped with various features that enhance the audio experience. The Pioneer VSX-522 supports multiple audio formats, including Dolby Digital and DTS. This allows for a more immersive sound experience while watching movies or listening to music. The receiver also has a built-in AM/FM tuner, providing access to a wide range of radio stations. With its HDMI connectivity, the Pioneer VSX-522 can be easily connected to compatible devices such as Blu-ray players and gaming consoles. This ensures high-quality audio and video playback. Additionally, the receiver has multiple input and output options, allowing for seamless integration with other audio equipment. The Pioneer VSX-522 offers convenient control options. It can be operated using the included remote control or through the Pioneer ControlApp, which allows for easy control through a smartphone or tablet. The receiver also has a user-friendly interface, making it easy to adjust settings and customize the audio experience. In terms of power, the Pioneer VSX-522 delivers clear and balanced sound. With its built-in amplifier, it provides ample power to drive speakers and deliver high-quality audio performance. Overall, the Pioneer VSX-522 is a reliable and versatile receiver that enhances the audio experience. Its advanced features, connectivity options, and user-friendly interface make it a great choice for audio enthusiasts looking to elevate their home theater setup.

General
BrandPioneer
ModelVSX-522
Productreceiver
EAN0884938163545
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer VSX-522 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

How do I connect my speakers to the Pioneer VSX-522 receiver?

Ensure the positive and negative terminals on the receiver match those on your speakers, then connect the speaker wires securely for optimal sound quality.

What is the best audio setup for my home theater system using the Pioneer VSX-522?

To maximize your home theater experience, a recommended setup would consist of a 5.1 channel surround sound, utilizing front, center, and surround speakers along with a subwoofer.

How can I adjust the audio settings on the Pioneer VSX-522?

Access the receiver's audio settings menu through the on-screen display or the front panel display and tailor parameters such as bass, treble, and equalizer settings to your personal preference.

How can I optimize the video quality on my TV when using the Pioneer VSX-522 receiver?

Make sure you connect your video source (such as a Blu-ray player or game console) directly to the HDMI input on the receiver, then use a high-quality HDMI cable to connect the receiver's HDMI Out port to your TV. This will ensure a seamless transmission of high-definition video signals.

How can I troubleshoot common issues like no sound or distorted audio on the Pioneer VSX-522?

Firstly, check that all speaker connections are secure. If the issue persists, ensure the correct input source is selected, and check the volume levels. If you are using external devices, verify their audio settings and connectivity. If problems persist, power cycle the receiver and connected devices to reset the system.

Is the manual of the Pioneer VSX-522 available in English?

Yes, the manual of the Pioneer VSX-522 is available in English .

Is your question not listed? Ask your question here

No results