Pioneer VSX-521-K manual

Pioneer VSX-521-K
8.5 · 9
PDF manual
 · 120 pages
English
manualPioneer VSX-521-K

Additional information

08
36
En
08

Chapter 8:

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Take a look at the other components and electrical appliances being used, because sometimes the problem may lie there. If the trouble isn’t sorted out even after going through the checks below, ask your nearest Pioneer authorized independent service company to carry out repair work.• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.
General
The power does not turn on.
Disconnect the power plug from the outlet, and insert again.
Make sure there are no loose strands of speaker wire touching
the rear panel. This could cause the receiver to shut off
automatically.
The receiver suddenly switches off.
When the Auto Power Down function is working, the power
will automatically turn off if the receiver has not operated for
several hours. Check the setting for the Auto Power Down
function (see The Auto Power Down menu on page 33).
After about a minute (you won’t be able to switch the unit on
during this time), switch the receiver back on. If the message
persists, call a Pioneer authorized independent service
company.
The power suddenly turns on or off, or the input suddenly
changes (When the Control with HDMI is ON).
This happens because of the synchronized operation due to
the Control with HDMI function. If synchronized operations
are not needed, set the Control with HDMI to OFF (see HDMI
Setup on page 34).
OVERHEAT shows in the display and the power turns off.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (see page 2).
Lower the volume level.
TEMP shows in the display and the volume level drops.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (see page 2).
Lower the volume level.
No sound is output when an input function is selected.
Use MASTER VOLUME to turn up the volume.
Press MUTE on the remote control to turn muting off.
Set the SIGNAL SEL to H (HDMI), C1/O1/O2 (digital) or A
(analog) according to the type of connections made (refer to
page 21).
Make sure the component is connected correctly (refer to
Connecting your equipment on page 10).
Check the audio output settings of the source component.
Refer to the instruction manual supplied with the source
component.
No image is output when an input function is selected.
Make sure the component is connected correctly (refer to
Connecting your equipment on page 10).
Use the same type of video cables for the source component
and TV to connect to this receiver (see About video outputs
connection on page 13).
Check The Input Assign menu on page 32 to make sure you’re
assigned the correct input.
The video input selected on the TV monitor is incorrect. Refer
to the instruction manual supplied with the TV.
No sound from subwoofer.
Make sure the subwoofer is switched on.
If the subwoofer has a volume knob, make sure it’s turned up.
The Dolby Digital or DTS source you are listening to may not
have an LFE channel.
Switch the subwoofer setting in Speaker Setting on page 30 to
YES or PLUS.
Switch the LFE ATT (LFE Attenuate) on page 28 to LFEATT 0 or
LFEATT 5.
No sound from surround or center speakers.
Connect the speakers properly (refer to page 11).
Refer to Speaker Setting on page 30 to check the speaker
settings.
Refer to Channel Level on page 31 to check the speaker levels.
The Phase Control feature doesn’t seem to have an audible
effect.
If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest
frequency setting. If there is a PHASE setting on your
subwoofer, set it to 0º (or depending on the subwoofer, the
setting where you think it has the best overall effect on the
sound).
Make sure the speaker distance setting is correct for all
speakers (see Speaker Distance on page 32).
Considerable noise in radio broadcasts.
Connect the antenna (page 17) and adjust the position for
best reception.
Route any loose cables away from the antenna terminals and
wires.
Fully extend the FM wire antenna, position for best reception,
and secure to a wall (or connect an outdoor FM antenna).
Connect an additional internal or external AM antenna
(page 18).
Turn off equipment causing interference or move it away from
the receiver (or move antennas farther away from equipment
causing noise).
Broadcast stations cannot be selected automatically.
Connect an outdoor antenna (refer to page 18).
Noise during playback of a cassette deck.
Move the cassette deck away from your receiver, until the
noise disappears.
No sound is output or a noise is output when software with
DTS is played back.
Make sure the player’s settings are correct and/or the DTS
signal out is on. Refer to the instruction manual supplied with
the DVD player.
There seems to be a time lag between the speakers and the
output of the subwoofer.
See Automatically setting up for surround sound (MCACC) on
page 19 to set up your system again using MCACC (this will
automatically compensate for a delay in the subwoofer
output).
After using the Auto MCACC setup, the speaker size setting
(LARGE or SMALL) is incorrect.
Low-frequency noise could have been caused by an air
conditioner or motor. Switch off all appliances in the room and
rerun the Auto MCACC setup.
VSX-521_UCSMXCN_En.book 36 ページ 󲃟󲃝󲃞󲃝年󲃞󲃟月󲃟󲃞日 火曜日 午後󲃟時󲃠5分

View the manual for the Pioneer VSX-521-K here, for free. This manual comes under the category receivers and has been rated by 9 people with an average of a 8.5. This manual is available in the following languages: English. Do you have a question about the Pioneer VSX-521-K or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 4
V
Varga istvánSeptember 2, 2020

Hi, I have a question. I connected the receiver to the TV via HDMI-1, and when I turn off the TV or unplug the receiver, the receiver also turns off and doesn't turn back on unless I reconnect it to the TV. Thank you very much in advance for your response, it's very important.

This message has been automatically translated
A
Alvin BergJanuary 16, 2022

How can I choose between the various sound options, such as concert or rock, using the IR unit or directly on the receiver?

How can I choose between the various sound options, such as concert or rock, using the IR unit or directly on the receiver?
zoom-in
View photo
This message has been automatically translated
J
Jim LowDecember 29, 2022

Does this model have the option of selecting between A or B speakers?

T
TitoFebruary 4, 2024

Where do connect a turntable

Where do connect a turntable
zoom-in
View photo

The Pioneer VSX-521-K is an audio receiver that delivers a RMS rated power of 550 watts. With a Signal-to-Noise Ratio (SNR) of 79 dB, it offers clear and high-quality sound. The Total Harmonic Distortion (THD) is impressively low at 0.05%, ensuring accurate audio reproduction without any noticeable distortion. This receiver has an impedance of 8 Ω, which is a commonly used standard for audio equipment. It supports 5.1 channels, providing an immersive audio experience with multiple speakers for surround sound. In terms of connectivity, the Pioneer VSX-521-K offers various options. It has multichannel audio input and output terminals, allowing for convenient connection to compatible devices. Additionally, it features two digital audio optical inputs and one digital audio coaxial input, enabling the transmission of high-quality digital audio signals. For video connectivity, the receiver is equipped with two component video inputs, four HDMI inputs, and one composite video input. These inputs allow for the integration of video components into the audio setup. The Pioneer VSX-521-K includes one HDMI output, which can be connected to a compatible display device. This output allows for seamless video transmission. Overall, the Pioneer VSX-521-K is a versatile audio receiver with ample power and connectivity options. Its low distortion and high SNR ensure accurate and clear audio reproduction, while the multiple input and output options make it suitable for a variety of audio and video setups.

General
BrandPioneer
ModelVSX-521-K | VSX-521-K
Productreceiver
LanguageEnglish
FiletypeUser manual (PDF)
Audio
RMS rated power550 W
Signal-to-Noise Ratio (SNR)79 dB
Total Harmonic Distortion (THD)0.05 %
Impedance8 Ω
Audio output channels5.1 channels
Frequency range20 - 20000 Hz
Power output per channel (20-20KHz@8 Ohm)- W
Power output per channel (1KHz@6 Ohm)125 W
Receiver type-
Technical details
Audio decodersDolby Digital EX, Dolby Digital Plus, Dolby Pro Logic IIz, Dolby TrueHD, DTS-HD
Product colorBlack
Handheld remote controlYes
Display-
EqualizerYes
Apple docking compatibilityNot supported
AirPlayNo
Inputs
Multichannel audio input typeTerminals
Digital audio optical in2
Digital audio coaxial in1
Component video (YPbPr/YCbCr) in2
HDMI in4
Composite video in1
Outputs
Multichannel audio output typeTerminals
Number of HDMI outputs1
Composite video out1
Headphone outputs2
Headphone connectivity3.5 mm
Ports & interfaces
Connectivity technologyWired
Speakers connectivity type-
Radio
Supported radio bandsAM, FM
AM band range530 - 1700 kHz
FM band range87.5 - 108 MHz
Preset stations quantity30
Video
3DYes
Weight & dimensions
Weight9000 g
Width435 mm
Depth363 mm
Height168 mm
Network
Ethernet LANNo
Wi-FiNo
Power
AC input voltage120 V
AC input frequency60 Hz
Power consumption (typical)415 W
Power consumption (standby)0.4 W
Optical drive
Optical drive includedNo
Storage
Card reader integrated-
Packaging content
ManualYes
Warranty cardYes
User guideYes
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer VSX-521-K below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is the weight of the Pioneer VSX-521-K?

The Pioneer VSX-521-K has a weight of 9000 g.

What is the height of the Pioneer VSX-521-K?

The Pioneer VSX-521-K has a height of 168 mm.

What is the width of the Pioneer VSX-521-K?

The Pioneer VSX-521-K has a width of 435 mm.

What is the depth of the Pioneer VSX-521-K?

The Pioneer VSX-521-K has a depth of 363 mm.

How do I connect my speakers to the Pioneer VSX-521-K receiver?

Make sure you connect the positive and negative terminals of each speaker to the corresponding terminals on the receiver. Remember to match the correct impedance and polarity for optimal sound performance.

How can I set up the auto-calibration feature on the receiver?

To use the auto-calibration feature, make sure you connect the included microphone to the receiver and place it at your listening position. Then, access the receiver's menu and follow the on-screen instructions to run the auto-calibration process, which will optimize the audio settings for your specific room.

How do I adjust the bass and treble settings on the Pioneer VSX-521-K?

To adjust the bass and treble settings, go to the receiver's menu and navigate to the audio settings. From there, you can easily modify the levels of bass and treble to suit your personal preferences.

How can I program the remote control to work with my TV?

To program the remote control to operate your TV, locate the remote's setup button and press it. Then, follow the on-screen instructions to enter the specific code for your TV brand. Once successfully programmed, the remote should control basic functions such as power, volume, and input selection for your TV.

How do I connect external devices, such as a Blu-ray player or game console, to the Pioneer receiver?

Connect the HDMI output of your external device to one of the HDMI inputs on the receiver. Then, using an HDMI cable, connect the HDMI output of the receiver to your TV or video display. Finally, select the appropriate HDMI input on the receiver to enjoy audio and video from your external device.

What is the RMS rated power of Pioneer VSX-521-K?

The RMS rated power of Pioneer VSX-521-K is 550 W. This means that it has a high power output, making it suitable for larger rooms or for those who want a louder audio experience.

What is the Signal-to-Noise Ratio (SNR) of Pioneer VSX-521-K?

The Signal-to-Noise Ratio (SNR) of Pioneer VSX-521-K is 79 dB. A higher SNR indicates that the receiver produces less background noise, resulting in clearer and more accurate audio playback.

What is the Total Harmonic Distortion (THD) of Pioneer VSX-521-K?

The Total Harmonic Distortion (THD) of Pioneer VSX-521-K is 0.05%. This means that the receiver maintains a low distortion level, ensuring that the audio is reproduced with high fidelity and minimal distortion.

What is the Impedance of Pioneer VSX-521-K?

The Impedance of Pioneer VSX-521-K is 8 Ω. This indicates the compatibility of the receiver with various speakers. Most speakers have an 8 Ω impedance rating, so this receiver should work well with a wide range of speakers.

How many audio output channels does Pioneer VSX-521-K have?

Pioneer VSX-521-K has 5.1 audio output channels. This means that it supports surround sound systems with five speakers and one subwoofer, resulting in a more immersive audio experience for the user.

Is the manual of the Pioneer VSX-521-K available in English?

Yes, the manual of the Pioneer VSX-521-K is available in English .

Is your question not listed? Ask your question here

No results