Pioneer VSX-329 manual

Pioneer VSX-329
8.7 · 52
PDF manual
 · 41 pages
English
manualPioneer VSX-329
7
7
37
Chapter
4
37
6

Additional information

Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Take a look at the other components and electrical appliances being used, because sometimes the problem may lie there. If the trouble isn’t sorted out even after going through the checks below, ask your nearest Pioneer authorized independent service company to carry out repair work.
If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.
General
The power does not turn on.
Disconnect the power plug from the outlet, and insert again.
Make sure there are no loose strands of speaker wire touching
the rear panel. This could cause the receiver to shut off
automatically.
The receiver suddenly switches off.
When the Auto Power Down function is working, the power will
automatically turn off if the receiver has not operated for
several hours. Check the setting for the Auto Power Down
function (see The Auto Power Down menu on page 35).
After about a minute (you won’t be able to switch the unit on
during this time), switch the receiver back on. If the message
persists, call a Pioneer authorized independent service
company.
If there is very little low frequency information in the source
material, change your speaker settings to Front: SMALL /
Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (
page 33).
The receiver suddenly switches off or the HDMI indicator
blinks.
Check that there are no loose strands of speaker wire touching
the rear panel or another set of wires. If so, re-attach the
speaker wires, making sure there are no stray strands.
The receiver may have a serious problem. Disconnect from the
power and call a Pioneer authorized independent service
company.
Power automatically turns ON/OFF and the input switches
from one to another. (When the ARC function is ON)
The CEC (Consumer Electronic Control) function may activate
when the ARC function is turned ON, causing power to turn
ON and OFF and the input to switch from one to another. Since
this unit does not guarantee synchronized operation based on
the CEC function, turn OFF the HDMI CONTROL setting on the
connected player. Refer to the relevant device’s instruction
manual for details.
If this does not work, turn OFF the ARC function. If this is the
case, listen to the TV audio after connecting this unit and the
TV with an audio cable.
OVERHEAT shows in the display and the power turns off.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (
page 2).
Lower the volume level.
TEMP shows in the display and the volume level drops.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (
page 2).
Lower the volume level.
No sound is output when an input function is selected.
Use
VOLUME +/–
to turn up the volume.
Press
MUTE
on the remote control to turn muting off.
Set the
SIGNAL SEL
to H (HDMI), C1/O1 (digital) or A (analog)
according to the type of connections made (
page 22).
Make sure the component is connected correctly (see
Connecting your equipment on page 10).
Check the audio output settings of the source component.
Refer to the instruction manual supplied with the source
component.
No image is output when an input function is selected.
Make sure the component is connected correctly (see
Connecting your equipment on page 10).
Use the same type of video cables for the source component
and TV to connect to this receiver (see
About video outputs
connection on page 13).
The video input selected on the TV monitor is incorrect. Refer
to the instruction manual supplied with the TV.
No sound from subwoofer.
Make sure the subwoofer is switched on.
If the subwoofer has a volume knob, make sure it’s turned up.
The Dolby Digital or DTS source you are listening to may not
have an LFE channel.
Switch the subwoofer setting in Speaker Setting on page 33 to
YES or PLUS.
Switch the LFE ATT (LFE Attenuate) on page 32 to LFEATT 0 or
LFEATT 5.
No sound from surround or center speakers.
Connect the speakers properly (page 11).
Refer to Speaker Setting on page 33 to check the speaker
settings.
Refer to Channel Level on page 34 to check the speaker levels.
The Phase Control feature doesn’t seem to have an
audible effect.
If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest
frequency setting. If there is a PHASE setting on your
subwoofer, set it to 0º (or depending on the subwoofer, the
setting where you think it has the best overall effect on the
sound).
Make sure the speaker distance setting is correct for all
speakers (see
Speaker Distance on page 35).
Considerable noise in radio broadcasts.
Connect the antenna (page 16) and adjust the position for best
reception.
Route any loose cables away from the antenna terminals and
wires.
Fully extend the FM wire antenna, position for best reception,
and secure to a wall (or connect an outdoor FM antenna).
Connect an additional internal or external AM antenna
(
page 16).
Turn off equipment causing interference or move it away from
the receiver (or move antennas farther away from equipment
causing noise).
Broadcast stations cannot be selected automatically.
Connect an outdoor antenna (page 16).
Noise during playback of a cassette deck.
Move the cassette deck away from your receiver, until the noise
disappears.
No sound is output or a noise is output when software
with DTS is played back.
Make sure the player’s settings are correct and/or the DTS
signal out is on. Refer to the instruction manual supplied with
the DVD player.
There seems to be a time lag between the speakers and
the output of the subwoofer (VSX-424 only).
See Automatically setting up for surround sound (MCACC) on
page 19 to set up your system again using MCACC (this will
automatically compensate for a delay in the subwoofer output).
After using the Auto MCACC setup, the speaker size
setting (LARGE or SMALL) is incorrect (VSX-424 only).
Low-frequency noise could have been caused by an air
conditioner or motor. Switch off all appliances in the room and
rerun the Auto MCACC setup.

View the manual for the Pioneer VSX-329 here, for free. This manual comes under the category receivers and has been rated by 52 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the Pioneer VSX-329 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 17
J
JOB CHARLESOctober 22, 2020

My Denon AVR X1000 stopped midway while updating firmware. There is no audio coming out from it. If started it goes to update retry mode automatically and after sometime shows connection error01. Kindly help.

1 comment
E
Emma of manua.lsDecember 19, 2023

If your Pioneer VSX-329 receiver is stuck in update retry mode and displays a connection error01 after your Denon AVR X1000 stopped midway while updating firmware, with no audio output, please follow these steps: 1. Check the connections: Make sure all the cables are securely connected between your devices and the receiver. Ensure that the HDMI cables are properly plugged in and that there are no loose strands of speaker wire touching the rear panel. 2. Power cycle the receiver: Disconnect the power plug from the outlet and wait for a few seconds before plugging it back in. This can help reset the receiver and resolve any temporary issues. 3. Check the speaker settings: If there is very little low-frequency information in the source material, adjust the speaker settings on the receiver. You can change the settings to Front: SMALL / Subwoofer: YES or Front: LARGE / Subwoofer: PLUS. 4. Verify the audio output settings: Ensure that the audio output settings of the source component are correctly configured. 5. Troubleshoot other components: Check the other components and electrical appliances being used in your setup. Sometimes, the problem may lie with a different device. Ensure that all the devices are functioning properly.

This answer is automatically generated
G
Gábor GöncziSeptember 12, 2023

Does this device support and handle optical cable? If yes... how to set it up or listen to its sound...

Does this device support and handle optical cable?
If yes... how to set it up or listen to its sound...
zoom-in
View photo
This message has been automatically translated
M
MariuszDecember 13, 2016

Hello, I have a problem with the balance. Specifically, the right column plays louder than the left. How can I adjust this?

This message has been automatically translated
D
Denis belle May 13, 2019

The reciever is not coming but on d display small red light for hdmi keeps flashing ?

1 comment
E
Emma of manua.lsOctober 25, 2023

The Pioneer VSX-329 receiver may not turn on if the small red light for HDMI keeps flashing on the display. Here are some troubleshooting steps you can try: 1. Disconnect the power plug from the outlet and plug it in again. 2. Check for any loose strands of speaker wire touching the back panel. This could cause the receiver to shut off automatically. 3. If the receiver suddenly switches off, check the setting for the Auto Power Down function. It may be turning off the power if the receiver has not been used for several hours. 4. After about a minute, turn the receiver back on. If the problem continues, contact a Pioneer authorized independent service company. 5. If there is very little low-frequency information in the source material, change your speaker settings to Front: SMALL / Subwoofer: YES or Front: LARGE / Subwoofer: PLUS. 6. Check that there are no loose strands of speaker wire touching the back panel or another set of wires. Reconnect the speaker wires, making sure there are no loose strands. 7. If none of the above steps solve the issue, the receiver may have a serious problem. Disconnect it from the power and contact a Pioneer authorized independent service company.

This answer is automatically generated
B
BIZARRO SOARESMarch 22, 2015

I cannot connect receiver i bought last week withthe tv ; i can hear sound from the tuner , but not from the tv I tried several conectios ; hdmi , optical , and analogue I think the problema must be at the receiver set up the display shows tv c1 or 01 as i change at the command .. I also cannot see the set up on the screen through the hdmi conection (out from the receiver , in on the tv) pls give me some advices thanks

D
DamienJuly 13, 2015

On my receiver i had the input for DVD set up for the bluray player, the game input for my playstation, but i can figure out how to have the TV input set u to receiver my digital signal so i dont have to go back and forth just run it from the receiver. How do i do this

A
AnnaJanuary 7, 2016

Hi,i do have Pioneer vsx-329.by misteake I did press I don't know which button on the remote and sound gone completely .I don't know how I can restarted all. If you have any ideas ,please help. Thanks

D
DanMarch 30, 2017

Hi.can I possibly use a tv as the hdmi input and play it through to a bigger tv via the hdmi out?thanks

V
VENKATESHJune 22, 2015

Sir I'm purchased pioneer 329 10days before standby off remote again on receiver no display HDMI light only on/off please send me sollution

1 comment
M
michael rambuyanJune 9, 2017

I have pioneer sir.no display.only hdmi light blinking.please send me a solution

The Pioneer VSX-329 is a receiver that offers 5.1 channels of audio output, providing users with a dynamic and immersive sound experience. With a power output of 105 W per channel at 1KHz and 6 Ohm, this receiver is capable of delivering clear and robust sound quality. Featuring a Total Harmonic Distortion (THD) of 1%, the Pioneer VSX-329 ensures minimal distortion in audio playback, guaranteeing accurate reproduction of the original sound source. For easy connectivity, this receiver comes equipped with multiple input options. It includes four HDMI inputs, allowing users to connect various audio/video devices such as gaming consoles, Blu-ray players, and set-top boxes. Additionally, there are two composite video inputs for connecting legacy devices, as well as digital audio optical and coaxial inputs for enhanced audio connectivity. With an input sensitivity of 200 mV and an output impedance of 6 Ω, the Pioneer VSX-329 ensures compatibility with a wide range of audio sources and speakers. Moreover, it offers a high Signal-to-Noise Ratio (SNR) of 98 dB, reducing background noise and delivering clear and detailed sound reproduction. Overall, the Pioneer VSX-329 provides users with a versatile and reliable receiver option for their home entertainment systems. Its robust power output, multiple input options, and low distortion levels make it suitable for various audio setups. Constructed with quality components, this receiver is designed to deliver consistent performance and durability over time.

General
BrandPioneer
ModelVSX-329 | VSX-329-K
Productreceiver
EAN4988028243929
LanguageEnglish
FiletypeUser manual (PDF)
Audio
Power output per channel (20-20KHz@8 Ohm)- W
Audio output channels5.1 channels
Power output per channel (1KHz@6 Ohm)105 W
Total Harmonic Distortion (THD)1 %
Input sensitivity200 mV
Output impedance6 Ω
Audio D/A Converter (DAC)24-bit/192kHz
Audio A/D Converter (ADC)24-bit/96kHz
Signal-to-Noise Ratio (SNR)98 dB
Frequency range10 - 70000 Hz
Receiver type-
Inputs
HDMI in4
Composite video in2
Digital audio optical in1
Digital audio coaxial in1
USB ports quantity1
AC (power) inYes
Outputs
Number of HDMI outputs1
Headphone outputs1
Ports & interfaces
Speakers connectivity type-
Network
Ethernet LANNo
Wi-FiNo
Radio
Supported radio bandsAM, FM
Radio Data System (RDS)Yes
Preset stations quantity30
Optical drive
Optical drive includedNo
Storage
Card reader integratedNo
Video
3D-
Technical details
Display-
Audio decodersDolby TrueHD, DTS-HD
x.v.Color supportYes
Deep color supportYes
Audio Return Channel (ARC)Yes
Bass adjustmentYes
Treble adjustmentYes
Graphical user interface (GUI)Yes
Graphical user interface (GUI) languageEnglish
Handheld remote controlYes
Product colorBlack
Audio amplifierYes
Sleep timerYes
Apple docking compatibilityNot supported
Surround modes quantity11
Audio Lip synchronizationYes
AirPlay-
USB 2.0 ports quantity1
Power
AC input voltage220-230 V
AC input frequency50 - 60 Hz
Power consumption (typical)155 W
Power consumption (standby)0.45 W
Weight & dimensions
Width435 mm
Depth331.5 mm
Height168 mm
Weight7200 g
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer VSX-329 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is the weight of the Pioneer VSX-329?

The Pioneer VSX-329 has a weight of 7200 g.

What is the height of the Pioneer VSX-329?

The Pioneer VSX-329 has a height of 168 mm.

What is the width of the Pioneer VSX-329?

The Pioneer VSX-329 has a width of 435 mm.

What is the depth of the Pioneer VSX-329?

The Pioneer VSX-329 has a depth of 331.5 mm.

How do I connect my devices to the receiver?

To connect your devices to the Pioneer VSX-329 receiver, locate the corresponding input ports on the back panel of the receiver. Use the appropriate cables to connect your devices, such as HDMI for video and audio, RCA for analog audio, or optical/coaxial cables for digital audio. Ensure the correct input source is selected on the receiver for each device.

How do I set up and optimize the audio?

Begin by running the auto calibration feature included in the Pioneer VSX-329. This will adjust speaker levels, distances, and equalization settings to provide optimal sound quality. Additionally, explore the receiver's audio settings to customize options such as surround sound modes, bass/treble adjustments, and dialogue enhancement to suit your preferences.

How can I program and control the remote for multiple devices?

The Pioneer VSX-329 remote control offers the ability to control other devices in your home theater setup. To program it, access the receiver's settings menu and navigate to the remote control programming section. Follow the on-screen instructions to automatically or manually configure it for your devices. Once programmed, use the remote's dedicated buttons to control power, volume, input selection, and other functions of your connected devices.

How can I use the receiver to play music through Bluetooth?

To play music via Bluetooth, activate the Bluetooth function on your desired playback device. Press the "Bluetooth" button on the receiver's front panel or remote control to enter pairing mode. On your playback device, select the Pioneer VSX-329 from the available Bluetooth devices list. Once connected, you can stream music wirelessly to the receiver and enjoy it through your connected speakers.

How do I troubleshoot common audio or video issues?

If you experience audio or video problems, start by checking the basics: ensure all cables are securely connected, devices are powered on, and the correct input source is selected. If the issue persists, try power cycling the receiver by unplugging it from the power source for a few minutes and then reconnecting it. If further troubleshooting is necessary, consult the receiver's on-screen menu for additional troubleshooting options such as resetting factory settings or updating firmware.

How many audio output channels does the Pioneer VSX-329 have?

The Pioneer VSX-329 has 5.1 audio output channels.

What is the power output per channel of the Pioneer VSX-329?

The Pioneer VSX-329 has a power output of 105 W per channel at 1KHz and 6 Ohm.

What is the total harmonic distortion of the Pioneer VSX-329?

The Pioneer VSX-329 has a total harmonic distortion of 1%.

How many HDMI inputs does the Pioneer VSX-329 have?

The Pioneer VSX-329 has 4 HDMI inputs.

Does the Pioneer VSX-329 have Wi-Fi or Ethernet LAN connectivity?

No, the Pioneer VSX-329 does not have Wi-Fi or Ethernet LAN connectivity.

Is the manual of the Pioneer VSX-329 available in English?

Yes, the manual of the Pioneer VSX-329 is available in English .

Is your question not listed? Ask your question here

No results