Pioneer VSX-1022 manual

Pioneer VSX-1022
8.2 · 5
PDF manual
 · 65 pages
English
manualPioneer VSX-1022

Additional information

10
10
60
After using the Auto MCACC setup, the speaker size
setting (LARGE or SMALL) is incorrect.
Low-frequency noise could have been caused by an air
conditioner or motor. Switch off all appliances in the room and
rerun the Auto MCACC setup.
Can’t operate the remote control.
Replace the batteries (page 10).
Operate within 7 m (23 ft.), 30º of the remote sensor (page 10).
Remove the obstacle or operate from another position.
Avoid exposing the remote sensor on the front panel to direct
light.
The display is dark or off.
Press
DIMMER
on the remote control repeatedly to return to
the default.
The front panel display switches over for no apparent
reason to various different displays.
This happens because the demo display is in operation. To turn
off the demo display, press any button to go back to the
original display, or set the FL Demo Mode to OFF (see The FL
Demo Mode menu on page 51).
The receiver doesn’t recognize iPod touch/iPhone.
Try the following.
1. Simultaneously keep pressing the sleep button and home
button on the iPod touch or iPhone for over 10 seconds to
restart.
2. Turn on the receiver.
3. Connect the iPod touch/iPhone to the receiver.
The
Bluetooth
wireless technology device cannot be
connected or operated. Sound from the
Bluetooth
wireless technology device is not emitted or the sound is
interrupted.
Check that no object that emits electromagnetic waves in the
2.4 GHz band (microwave oven, wireless LAN device or
Bluetooth wireless technology apparatus) is near the unit. If
such an object is near the unit, set the unit far from it. Or, stop
using the object emitting the electromagnetic waves.
Check that the Bluetooth wireless technology device is not too
far from the unit and that obstructions are not set between the
Bluetooth wireless technology device and the unit. Set the
Bluetooth wireless technology device and the unit so that the
distance between them is less than about 10 m and no
obstructions exist between them.
Check that the Bluetooth ADAPTER and the ADAPTER PORT
terminal of the unit are correctly connected.
The Bluetooth wireless technology device may not be set to the
communication mode supporting the Bluetooth wireless
technology. Check the setting of the Bluetooth wireless
technology device.
Check that pairing is correct. The pairing setting was deleted
from this unit or the Bluetooth wireless technology device.
Reset the pairing.
Check that the profile is correct. Use a Bluetooth wireless
technology device that supports A2DP profile and AVRCP
profile.

NETWORK feature

Cannot access the network.
The LAN cable is not firmly connected. Firmly connect the LAN
cable (page 20).
The router is not switched on. Switch on the router.
Internet security software is currently installed in the
connected component. There are cases where a component
with Internet security software installed cannot be accessed.
The audio component on the network which has been
switched off is switched on. Switch on the audio component
on the network before switching on this receiver.
Playback does not start while ‘Connecting Wired...’
continues to be displayed.
The component is currently disconnected from this receiver or
the power supply. Check whether the component is properly
connected to this receiver or the power supply.
The PC or Internet radio is not properly operated.
The corresponding IP address is not properly set. Switch on the
built-in DHCP server function of your router, or set up the
network manually according to your network environment
(page 51).
The IP address is being automatically configured. The
automatic configuration process takes time. Please wait.
The audio files stored on components on the network,
such as a PC, cannot be played back.
Windows Media Player 11 or Windows Media Player 12 is not
currently installed on your PC. Install Windows Media Player 11
or Windows Media Player 12 on your PC.
Audio files recorded in MPEG-4 AAC or FLAC are being played
back on Windows Media Player 11 or Windows Media Player
12. Audio files recorded in MPEG-4 AAC or FLAC cannot be
played back on Windows Media Player 11 or Windows Media
Player 12. Try using another server. Refer to the operation
manual supplied with your server.
The component connected to the network is not properly
operated.
-
Check whether the component is affected by special
circumstances or is in the sleep mode.
-
Try rebooting the component if necessary.
The component connected to the network does not permit file
sharing. Try changing the settings for the component
connected to the network.
The folder stored on the component connected to the network
has been deleted or damaged. Check the folder stored on the
component connected to the network.

View the manual for the Pioneer VSX-1022 here, for free. This manual comes under the category receivers and has been rated by 5 people with an average of a 8.2. This manual is available in the following languages: English. Do you have a question about the Pioneer VSX-1022 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 5
B
Bob D.July 26, 2023

The unit appears to be functioning as designed, but the visual display is totally blank. Is there something that we could have hit? That would shut the display off if so how do I reset it.

The unit appears to be functioning as designed, but the visual display is totally blank. Is there something that we could hav...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 25, 2023

To reset the Pioneer VSX-1022 receiver and potentially fix the blank screen issue, follow these steps: 1. Switch the receiver into standby mode. 2. While holding down the BAND button, press and hold the STANDBY/ON button for about two seconds. 3. When you see "RESET?" appear on the display, press the AUTO SURROUND/STREAM DIRECT button. 4. Press the ALC/STANDARD SURR button to confirm the reset. 5. "OK" will appear on the display, indicating that the receiver has been reset to the factory default settings.

This answer is automatically generated
G
Gary McDannelSeptember 18, 2023

Is there a way to set-up the receiver so that when it turns on, a specific input signal (e.g., DVR/BDR) is automatically selected?

Is there a way to set-up the receiver so that when it turns on, a specific input signal (e.g., DVR/BDR) is automatically sele...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 25, 2023

Yes, there is a way to configure the Pioneer VSX-1022 receiver to automatically select a specific input signal when it is turned on. Here are the steps to configure this setting: 1. Press the "Home Menu" button on the receiver. 2. Navigate to the "HDMI Setup" option using the arrow keys. 3. Select the "Control" option and set it to "ON". 4. Choose the "ARC" setting and set it to "ON" if you want the TV's sound to be input via the HDMI terminal. If you prefer the TV's sound to be input from the audio input terminals other than HDMI, set the "ARC" setting to "OFF". 5. Select the "Standby Through" setting and choose the HDMI input signal that you want to be output to the TV when the receiver is in standby mode. If you want the receiver to remember the last selected HDMI input signal, choose the "LAST" option. This can only be selected when the "Control" setting is set to "OFF".

This answer is automatically generated
D
DonnaMarch 6, 2021

Why would the unit turn On for seconds then automatically turn off ?

Why would the unit turn On for seconds then automatically turn off ?
zoom-in
View photo
1 comment
M
Mark BalandApril 23, 2022

The unit might not be getting enough power. It’s a 1000 watt receiver. I had one for years, but my old wiring started having problems. The receiver would click on and off. I had to switch to a low powered (100 watt) sound bar.

G
Greg N.January 16, 2023

Can I adjust volume levels to be consistent between inputs for different devices?

B
Bob FlynnJune 11, 2023

I have a vsx-1022 and a Sony xbr-65x950g TV. The receiver is connected to the eARC input, a firestick is in HDMI 1 and a Tivo is in HDMI 2. everything works well and the tv remote controls the receiver. I cannot, however get into the home menu to set up my speakers, therefore I do not have surround sound. I have 4 6.5" ceiling speakers, a front speaker on the wall over the TV and a woofer. I get sound, just not surround sound. I need help getting into the menu as the TV reports no signal when I choose the eARC input that the receiver is connected to.

The Pioneer VSX-1022 is a receiver that delivers a power output of 80 watts per channel at 8 Ohm and has 7.1 audio output channels. It offers versatile connectivity options with six HDMI inputs, one component video input, two composite video inputs, two digital audio optical inputs, and two digital audio coaxial inputs. Additionally, it is equipped with one remote (IR) input, one Ethernet LAN (RJ-45) port, and one HDMI output. The receiver allows for seamless integration with various multimedia devices, making it suitable for home theater setups. It supports high-definition video and audio formats, ensuring an immersive audiovisual experience. Its multiple HDMI inputs enable connection to gaming consoles, Blu-ray players, and other compatible devices, while the HDMI output allows for convenient connectivity to a compatible television or projector. Built with durable components, the Pioneer VSX-1022 ensures reliable performance and longevity. Its sleek and compact design allows for easy placement within a home entertainment system setup. With its 140-watt power output per channel at 6 Ohm, the receiver is capable of delivering powerful and clear sound, enhancing the overall audio quality of movies, music, and other multimedia content. The inclusion of one remote (IR) output further adds to its usability, enabling control of other compatible devices within the system. Its Ethernet LAN (RJ-45) port promotes network connectivity and allows for integration with streaming services and online content. Overall, the Pioneer VSX-1022 receiver offers a range of features and connectivity options, making it a suitable choice for those seeking to enhance their audiovisual experience.

General
BrandPioneer
ModelVSX-1022 | VSX1022K
Productreceiver
LanguageEnglish
FiletypeUser manual (PDF)
Audio
Power output per channel (20-20KHz@8 Ohm)80 W
Audio output channels7.1 channels
Power output per channel (1KHz@8 Ohm)110 W
Power output per channel (1KHz@6 Ohm)140 W
Audio D/A Converter (DAC)24-bit/192kHz
Receiver type-
Inputs
HDMI in6
Component video (YPbPr/YCbCr) in1
Composite video in2
Digital audio optical in2
Digital audio coaxial in2
Remote (IR) input1
Ethernet LAN (RJ-45) ports1
Outputs
Number of HDMI outputs1
Remote (IR) output1
Headphone outputs1
Headphone connectivity3.5 mm
Ports & interfaces
Speakers connectivity type-
Connectivity technologyWired
File formats
Audio formats supportedAAC, FLAC, MP3, WAV, WMA
Network
Ethernet LANYes
Wi-FiNo
BluetoothNo
Radio
Supported radio bandsAM, FM
Internet radio services supportedPandora, vTuner
Optical drive
Optical drive includedNo
Storage
Card reader integrated-
Video
3DYes
Technical details
Display-
Audio decodersDolby Digital Plus, Dolby Pro Logic IIz, Dolby TrueHD, DTS-HD Master Audio
x.v.Color supportYes
Audio Return Channel (ARC)Yes
Handheld remote controlYes
Product colorBlack
Audio amplifierYes
Sleep timerYes
Volume controlRotary
On Screen Display (OSD)Yes
Apple docking compatibilityYes
Audio Lip synchronizationYes
AirPlayYes
AV inputYes
Graphical user interface (GUI)Yes
Bi-ampingYes
Apple dockingYes
Yes
Weight & dimensions
Width435.1 mm
Depth342.39 mm
Height167.64 mm
Weight9371 g
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer VSX-1022 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is the weight of the Pioneer VSX-1022?

The Pioneer VSX-1022 has a weight of 9371 g.

What is the height of the Pioneer VSX-1022?

The Pioneer VSX-1022 has a height of 167.64 mm.

What is the width of the Pioneer VSX-1022?

The Pioneer VSX-1022 has a width of 435.1 mm.

What is the depth of the Pioneer VSX-1022?

The Pioneer VSX-1022 has a depth of 342.39 mm.

How can I connect my TV to the Pioneer VSX-1022 receiver?

To connect your TV to the receiver, use an HDMI cable. Connect one end of the cable to the HDMI output on the receiver and the other end to the HDMI input on your TV. Make sure to select the correct HDMI input on your TV to enjoy audio and video through the receiver.

What is the maximum power output of the Pioneer VSX-1022 receiver?

The Pioneer VSX-1022 has a maximum power output of 80 Watts per channel. This means it is capable of delivering sufficient power to drive most home theater speakers efficiently.

How can I set up the speaker configuration on the Pioneer VSX-1022?

To set up the speaker configuration, go to the receiver's settings menu and select the "Speaker Setup" or "Audio Settings" option. From there, you can specify the number of speakers in your setup, adjust their size (large or small), and set individual channel levels for optimal sound balance.

Can the Pioneer VSX-1022 receiver be connected to a wireless network?

Unfortunately, the Pioneer VSX-1022 does not have built-in Wi-Fi connectivity. However, it does have an Ethernet port at the rear. To connect to a wireless network, you would need to use an external Wi-Fi adapter compatible with the receiver's specifications.

How can I perform a factory reset on the Pioneer VSX-1022?

To perform a factory reset, turn off the receiver and then press and hold the "BAND" button on the front panel. While holding the button, press the "STANDBY/ON" button. Continue holding the "BAND" button until "Reset?" appears on the display. Press the "AUTO SURR/STREAM DIRECT" button to confirm the reset and restore the receiver to its default settings.

How many HDMI inputs does the Pioneer VSX-1022 have?

The Pioneer VSX-1022 has 6 HDMI inputs.

What is the power output per channel at 8 Ohms?

The power output per channel at 8 Ohms is 80 Watts.

How many audio output channels does the Pioneer VSX-1022 have?

The Pioneer VSX-1022 has 7.1 audio output channels.

What is the power output per channel at 1KHz and 8 Ohms?

The power output per channel at 1KHz and 8 Ohms is 110 Watts.

What is the power output per channel at 1KHz and 6 Ohms?

The power output per channel at 1KHz and 6 Ohms is 140 Watts.

Is the manual of the Pioneer VSX-1022 available in English?

Yes, the manual of the Pioneer VSX-1022 is available in English .

Is your question not listed? Ask your question here

No results