Pioneer S-ES3TB manual

Pioneer S-ES3TB
8.6 · 1
PDF manual
 · 20 pages
English
manualPioneer S-ES3TB
1
En

S-ES3TB

Operating Instructions

Speaker System

WHAT’S IN THE BOX

BEFORE USE

Thank you for buying this Pioneer product.
Please read through these operating instructions before
using your speaker system to optimize performance.
The nominal impedance of this speaker system is
8 Ω. Connect the speaker system to an amplifier with
a load impedance ranging from 6 Ω to 16 Ω (a model
with “6 Ω to 16 Ω” displayed on the speaker output
terminals).
In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
-Be sure to turn the connected devices off and
remove the power cord from the wall outlet
beforehand when changing the connection or
installation method.
-Do not use excessive amplifier volume if using a
tone control to emphasize high or low frequencies.
Do not use the speaker to output distorted sound for
long periods of time. This can result in a fire hazard.

INSTALLATION PRECAUTIONS

Do not install these units near a stove or other
heating appliance, or put them in a place exposed to
the sun. Such locations may cause the cabinet to
change color and the speaker system to break down.
FRONT / CENTER SPEAKERS
Do not attach the front and center speakers to the
wall or ceiling. It may fall off and cause injury.
This speaker system is magnetically shielded.
However, depending on the installation location,
color distortion may occur if the speaker system is
installed extremely close to the screen of a television
set.
If this happens, turn off the television, then turn it on
again after 15 min to 30 min. If the problem persists,
place the speaker system away from the television
set.
Do not install your speakers overhead on the ceiling
or wall. The grille is designed to be detachable, and
as such it may fall and cause damage or personal
injury if installed overhead.
SURROUND SPEAKERS
The surround speakers are not magnetically shielded
and so should not be placed near a TV or monitor, as
the interaction of magnetic materials can cause
distortion of the colors on your TV screen. Magnetic
storage media (such as floppy discs and tape or video
cassettes) should also not be kept close to these
speakers.

PLACEMENT AND FINE TUNING

FRONT SPEAKERS
For best results the speakers should be separated a
distance approximately equal to the listening distance.
Angling the speakers inward towards the listener will
improve the image stability for non-central listeners.
Close proximity to a side or rear wall will enhance the
midbass performance, although too close (particularly a
corner location) and the bass may be unnaturally high
and image performance may be degraded.
Front speakers x 2
Surround speakers x 2
Speaker cords x 5
Center speaker x 1
Non-skid pads x 12
(4 pcs x 3 sheets)
Grilles (for front speaker) x 2
Operating instructions
Center
(2 m, Tie color : Black)
Front right / left
(3 m, Tie color : Blue)
Surround right / left
(10 m, Tie color : Red)
S-ES3TB_En.fm 1 ページ 2010年4月13日 火曜日 午前11時30分

View the manual for the Pioneer S-ES3TB here, for free. This manual comes under the category speakers and has been rated by 1 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Pioneer S-ES3TB or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 1
M
Mlamuli ShangeDecember 28, 2023

Why sub woofer doesn't have magnetic oo connection?

The Pioneer S-ES3TB is a set of home theatre speakers designed to enhance your audio experience. This speaker system includes a center speaker and satellite speakers, allowing for immersive sound quality. Both the center speaker and satellite speakers have an impedance of 8 Ω, ensuring compatibility with a wide range of audio devices. The center speaker weighs 2500 g and has dimensions of 350 x 162 x 130 millimeters (WxDxH). These measurements indicate a compact and lightweight design, making it easy to place the speaker in various room setups. The Pioneer S-ES3TB features a woofer diameter of 160 millimeters and a tweeter diameter of 26 millimeters. This combination enables clear and balanced audio reproduction across a wide frequency range. With 4.1 channels of audio output, this speaker system delivers rich and dynamic sound. Whether you're watching movies, playing games, or listening to music, the Pioneer S-ES3TB provides an immersive audio experience. Constructed with premium materials, these speakers are built to withstand the test of time. The attention to detail in their design ensures reliability and durability. Overall, the Pioneer S-ES3TB offers a high-quality audio solution for your home theatre setup. Its compact size, impressive audio output, and durable construction make it a suitable choice for enhancing your audio experience.

General
BrandPioneer
ModelS-ES3TB | S-ES3TB
Productspeaker
EAN4988038111034, 884938111034, 0884938111034
LanguageEnglish
FiletypeUser manual (PDF)
Other features
TypeHome theatre speakers
Center speaker impedance8 Ω
Satellite speaker impedance8 Ω
Center speaker frequency range50 - 20000 Hz
Satellite speaker frequency range40 - 30000 Hz
Center speaker weight2500 g
Center speaker dimensions (WxDxH)350 x 162 x 130 mm
Loudspeakers
Woofer diameter160 mm
Tweeter diameter26 mm
Audio output channels4.1 channels
Audio
RMS rated power- W
Technical details
TypeHome theatre speakers
Center speaker
Center speaker impedance8 Ω
Center speaker frequency range50 - 20000 Hz
Center speaker weight2500 g
Center speaker dimensions (WxDxH)350 x 162 x 130 mm
Satellite speakers
Satellite speaker impedance8 Ω
Satellite speaker frequency range40 - 30000 Hz
Performance
Audio output channels4.1 channels
RMS rated power- W
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer S-ES3TB below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is the impedance of Pioneer S-ES3TB center speaker?

The impedance of Pioneer S-ES3TB center speaker is 8 Ω. This means it will work well with most audio receivers and amplifiers on the market.

What is the impedance of Pioneer S-ES3TB satellite speakers?

The impedance of Pioneer S-ES3TB satellite speakers is 8 Ω. This ensures compatibility with a range of audio systems and makes it easier to pair with other speakers.

What is the woofer diameter of Pioneer S-ES3TB?

The woofer diameter of Pioneer S-ES3TB is 160 mm. This larger-sized woofer allows for deeper bass response and enhanced audio quality.

What is the tweeter diameter of Pioneer S-ES3TB?

The tweeter diameter of Pioneer S-ES3TB is 26 mm. This smaller-sized tweeter is capable of producing crisp and clear high-frequency sounds.

How many audio output channels does Pioneer S-ES3TB have?

Pioneer S-ES3TB has 4.1 audio output channels. This means it offers surround sound experience with four satellite speakers and one center speaker, providing immersive audio for home theater setups.

How do I connect the Pioneer S-ES3TB speaker system to an amplifier?

To connect the Pioneer S-ES3TB speaker system to an amplifier, follow these steps: 1. Make sure the amplifier is turned off and the power cord is unplugged from the wall outlet before making any connections. 2. Identify the speaker cords that came with the Pioneer S-ES3TB speaker system. There should be five speaker cords in total. 3. Connect one end of each speaker cord to the corresponding speaker terminals on the back of the amplifier. The terminals are usually labeled with positive (+) and negative (-) symbols. 4. Connect the other end of each speaker cord to the corresponding speaker terminals on the back of the Pioneer S-ES3TB speakers. Again, match the positive (+) and negative (-) symbols on the terminals. 5. Ensure that the speaker cords are securely connected to both the amplifier and the speakers. 6. Once all the connections are made, double-check that the speaker cords are properly attached and tightened. 7. Plug in the power cord of the amplifier and turn it on. 8. Gradually increase the volume on the amplifier to a comfortable listening level. By following these steps, you should be able to successfully connect the Pioneer S-ES3TB speaker system to an amplifier and enjoy your audio experience.

What should I do if the speaker system is not producing any sound?

If the Pioneer S-ES3TB speaker system is not producing any sound, you can follow these troubleshooting steps: 1. Check the speaker cords and connections. Ensure that the speaker cords are securely connected to both the amplifier and the speakers. If there are any loose or damaged cords, replace them. 2. Verify that the amplifier is turned on. Sometimes, the amplifier may be turned off or in standby mode, which can result in no sound output. Turn on the amplifier and adjust the volume control. 3. Gradually increase the volume on the amplifier. If the volume control is set to zero or a very low level, there may be no sound output. Slowly turn up the volume to a comfortable listening level. 4. If the sound is distorted, it could be due to extreme signal conditions. Lower the output level of the amplifier by adjusting the volume, bass control, or bass boost settings. By following these troubleshooting steps, you should be able to identify and resolve the issue of the Pioneer S-ES3TB speaker system not producing any sound.

Can I attach the front and center speakers of the Pioneer S-ES3TB to the wall or ceiling?

Yes, you can attach the front and center speakers of the Pioneer S-ES3TB to the wall. Here are the steps to do so: 1. Ensure that the wall you intend to mount the speakers on is strong enough to support them. Do not mount on plywood or soft surface walls. 2. Purchase suitable screws that are compatible with the wall material and can support the weight of the speakers. Note that mounting screws are not supplied with the speakers. 3. For the front speakers, pass a commercially-available reinforced string through the plastic catch to securely support the speaker to the wall. Be sure that the wall is strong enough to support the weight of the speaker. Do not attach the plastic catch directly to the wall; it should only be used in conjunction with reinforced string to prevent the speaker from falling. 4. For the center speaker, position it below the TV, aligning the front of the speaker with the front of the TV. Do not place the center speaker on top of the TV to avoid the risk of falling. By following these steps, you can safely attach the front and center speakers of the Pioneer S-ES3TB to the wall for optimal placement and performance.

Why is there color distortion on my TV when the Pioneer S-ES3TB speakers are installed close to it?

When the Pioneer S-ES3TB speakers are installed close to the TV, color distortion may occur. Here are the possible causes and solutions: 1. Magnetic Interference: The magnetic field generated by the speakers can interfere with the TV's screen, causing color distortion. To resolve this issue, keep the speakers at a safe distance from the TV, preferably at least one meter away. 2. Magnetic Storage Media: Avoid placing magnetic storage media, such as computer disks or audio/video tapes, near the speakers. These media can be affected by the magnetic field and result in color distortion on the TV screen. Store them away from the speakers. By following these steps, you can prevent color distortion on your TV when the Pioneer S-ES3TB speakers are installed close to it.

What should I do if the surround speakers of the Pioneer S-ES3TB are causing distortion of colors on my TV screen?

When the surround speakers of the Pioneer S-ES3TB are causing distortion of colors on your TV screen, you can take the following steps to address the issue: 1. Check the positioning of the surround speakers. Ensure that they are not placed too close to the TV screen. Maintain a safe distance of at least one meter between the speakers and the TV to prevent magnetic interference. 2. Verify that there are no magnetic storage media, such as computer disks or audio/video tapes, near the surround speakers. These media can be affected by the magnetic field and result in color distortion on the TV screen. Store them away from the speakers. 3. Adjust the volume levels of the surround speakers. If the volume is set too high, it can cause distortion. Lower the volume to a comfortable level and test if the color distortion improves. By following these steps, you can mitigate the issue of color distortion on your TV screen caused by the surround speakers of the Pioneer S-ES3TB.

How should I position the front speakers of the Pioneer S-ES3TB for optimal performance?

To position the front speakers of the Pioneer S-ES3TB for optimal performance, follow these steps: 1. Separate the front speakers at a distance approximately equal to the listening distance. This helps create a balanced soundstage. 2. Angle the speakers inward towards the listener. This improves the image stability, especially for non-central listeners. 3. Consider the proximity to walls. Placing the speakers close to a side or rear wall can enhance the midbass performance. However, be cautious not to position them too close, particularly in a corner, as this may result in unnaturally high bass and degraded image performance. By following these steps, you can position the front speakers of the Pioneer S-ES3TB in a way that optimizes the sound quality and imaging for an immersive audio experience.

Why is the bass performance and image quality affected when the Pioneer S-ES3TB speakers are placed close to walls?

When the Pioneer S-ES3TB speakers are placed close to walls, the bass performance and image quality can be affected due to the following reasons: 1. Reflections: Placing the speakers close to walls can cause sound reflections. These reflections can interfere with the original sound waves, leading to a muddier bass response and reduced clarity in the overall sound reproduction. 2. Boundary Effect: The proximity of the speakers to walls creates a phenomenon known as the boundary effect. This effect can amplify certain frequencies, particularly in the lower range, resulting in an exaggerated and boomy bass response. 3. Image Localization: Placing the speakers too close to walls can also affect the imaging or soundstage. The sound waves can bounce off the walls and interfere with the perception of the stereo image, making it less precise and accurate. To mitigate these issues, it is recommended to position the speakers away from walls, allowing for proper sound dispersion and minimizing reflections. By creating some distance between the speakers and walls, you can achieve improved bass performance and maintain better image quality for an enhanced listening experience.

Is the manual of the Pioneer S-ES3TB available in English?

Yes, the manual of the Pioneer S-ES3TB is available in English .

Is your question not listed? Ask your question here

No results