Pioneer S-ES21-LR-K manual

Pioneer S-ES21-LR-K
8.8 · 7
PDF manual
 · 16 pages
English
manualPioneer S-ES21-LR-K
1
En

S-ES21-LR-K

S-ES21-LR-T

Operating Instructions

Speaker System

WHAT’S IN THE BOX

BEFORE USE

Thank you for buying this Pioneer product.
Please read through these operating instructions before
using your speaker system to optimize performance.
This speaker system has an impedance of 8 Ω, and
should be connected only to an amplifier designed
with a load impedance of 8 Ω (the amplifier’s speaker
output connector should clearly be labeled “8 Ω“).
In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
-Be sure to turn the connected devices off and
remove the power cord from the wall outlet
beforehand when changing the connection or
installation method.
-Do not use excessive amplifier volume if using a
tone control to emphasize high or low frequencies.
Do not use the speaker to output distorted sound for
long periods of time. This can result in a fire hazard.

INSTALLATION PRECAUTIONS

Do not install these units near a stove or other
heating appliance, or put them in a place exposed to
the sun. Such locations may cause the cabinet to
change color and the speaker system to break down.
Do not attach the front speakers to the wall or ceiling.
It may fall off and cause injury.
Placing the stand on an unstable surface can be
dangerous. Be sure to place it on a flat, firm surface.
This speaker system is magnetically shielded.
However, depending on the installation location,
color distortion may occur if the speaker system is
installed extremely close to the screen of a television
set.
If this happens, turn off the television, then turn it on
again after 15 min to 30 min. If the problem persists,
place the speaker system away from the television
set.
Do not install your speakers overhead on the ceiling
or wall. The grille is designed to be detachable, and
as such it may fall and cause damage or personal
injury if installed overhead.
Do not place heavy or large objects on top of the
speaker. Doing so could provoke the speaker to fall,
causing damages or bodily
injury.

PLACEMENT AND FINE TUNING

For best results the speakers should be separated a
distance approximately equal to the listening distance.
Angling the speakers inward towards the listener will
improve the image stability for non-central listeners.
Close proximity to a side or rear wall will enhance the
midbass performance, although too close (particularly a
corner location) and the bass may be unnaturally high
and image performance may be degraded.
Front speaker x 2
Speaker cords x 2
Front Grilles x 2
Operating instructions
S-ES21-LR.fm 1 ページ 2013年7月18日 木曜日 午前9時25分

View the manual for the Pioneer S-ES21-LR-K here, for free. This manual comes under the category speakers and has been rated by 7 people with an average of a 8.8. This manual is available in the following languages: English. Do you have a question about the Pioneer S-ES21-LR-K or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Pioneer S-ES21-LR-K speaker set unit is designed for use in a 2.0 channel audio system. With a speaker placement on the floor and a reflex enclosure, this speaker set is intended to be positioned at the front of the room for optimal sound projection. It features three drivers, including a tweeter and a woofer, which enhance the audio experience by delivering clear high-frequency and deep low-frequency sounds. The tweeter of the Pioneer S-ES21-LR-K has a diameter of 52 millimeters, while the woofer has a larger diameter of 160 millimeters. This size difference allows for better separation and accuracy in reproducing different ranges of sound frequencies. Although the speaker set is not suitable for outdoor use, it offers a high RMS rated power of 150 watts, providing a powerful sound output. Additionally, it has an impedance of 8 ohms, which can ensure compatibility with various audio setups. Overall, the Pioneer S-ES21-LR-K speaker set unit is a reliable and durable option for those looking to enhance their home audio setup. Its floor placement and reflex enclosure contribute to the optimal positioning and projection of sound. With its three drivers, including a tweeter and woofer, it is capable of reproducing a wide range of frequencies with clarity. The speaker set's high RMS rated power and impedance also add to its versatility and compatibility with different audio setups.

General
BrandPioneer
ModelS-ES21-LR-K | S-ES21-LR-K
Productspeaker
EAN0884938227117
LanguageEnglish
FiletypeUser manual (PDF)
Performance
Recommended usageSpeaker set unit
Suitable for outdoor useNo
Product colorBlack
Bass reflexYes
Housing materialWood
Loudspeakers
Audio output channels2.0 channels
Speaker placementFloor
Speaker enclosureReflex
Speaker positionFront
Number of drivers3
TweeterYes
WooferYes
Tweeter diameter52 mm
Woofer diameter160 mm
Speaker type2-way
Amplifier
Amplifier-
Audio
RMS rated power150 W
Frequency range40 - 20000 Hz
Impedance8 Ω
Sensitivity84 dB
Other features
Equalizer-
Magnetically shieldedYes
Ports & interfaces
Connectivity technologyWired
Weight & dimensions
Width220 mm
Depth247 mm
Height247 mm
Weight9000 g
Power
Power source typeAC
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer S-ES21-LR-K below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is the weight of the Pioneer S-ES21-LR-K?

The Pioneer S-ES21-LR-K has a weight of 9000 g.

What is the height of the Pioneer S-ES21-LR-K?

The Pioneer S-ES21-LR-K has a height of 247 mm.

What is the width of the Pioneer S-ES21-LR-K?

The Pioneer S-ES21-LR-K has a width of 220 mm.

What is the depth of the Pioneer S-ES21-LR-K?

The Pioneer S-ES21-LR-K has a depth of 247 mm.

Does the Pioneer S-ES21-LR-K speaker set unit have a reflex speaker enclosure?

Yes, the Pioneer S-ES21-LR-K speaker set unit has a reflex speaker enclosure. This means that it is designed to enhance the low-frequency response and deliver deep bass for a more immersive audio experience.

Is the Pioneer S-ES21-LR-K suitable for outdoor use?

No, the Pioneer S-ES21-LR-K is not suitable for outdoor use. It is recommended to be used indoors for optimal performance and longevity.

Does the Pioneer S-ES21-LR-K have a tweeter and a woofer?

Yes, the Pioneer S-ES21-LR-K has both a tweeter and a woofer. This speaker set unit offers a balanced sound reproduction with the tweeter handling the high frequencies and the woofer taking care of the mid and low frequencies.

What is the rated power of the Pioneer S-ES21-LR-K?

The Pioneer S-ES21-LR-K has a RMS rated power of 150 W. This means that it can deliver a high and powerful audio output, providing a dynamic listening experience.

Is the Pioneer S-ES21-LR-K magnetically shielded?

Yes, the Pioneer S-ES21-LR-K is magnetically shielded. This feature prevents magnetic interference with nearby electronic devices, ensuring a clean and undistorted sound output.

How do I connect the Pioneer S-ES21-LR-K speaker to my audio system?

To connect the Pioneer S-ES21-LR-K speaker to your audio system, follow these steps: 1. Before making any connections, ensure that all equipment is turned off. 2. Identify the speaker terminals on the rear of your amplifier. The terminals should be clearly labeled, with one terminal marked as "+" (positive) and the other as "-" (negative). 3. Take the red marked speaker cord and connect it to the red (+) terminal on the amplifier. Connect the other end of the cord to the corresponding red (+) terminal on the rear of the Pioneer S-ES21-LR-K speaker. 4. Take the other speaker cord and connect it to the black (-) terminal on the amplifier. Connect the other end of the cord to the corresponding black (-) terminal on the rear of the speaker. 5. After connecting the cords, gently pull on them to ensure they are securely attached to the terminals. Loose connections can cause noise or interruptions in the sound. 6. Repeat the above steps for the second speaker if you have a stereo setup. 7. Once all the connections are made, double-check that everything is securely connected and tightened. 8. Finally, turn on your audio system and test the speakers to ensure they are working properly. By following these steps, you will be able to successfully connect the Pioneer S-ES21-LR-K speaker to your audio system.

Why is there no sound coming from the Pioneer S-ES21-LR-K speaker?

If there is no sound coming from the Pioneer S-ES21-LR-K speaker, you can try the following troubleshooting steps: 1. Check the speaker cord and connection: Ensure that the speaker cord is properly connected to both the speaker and the amplifier. Make sure the connections are secure and there are no loose or damaged wires. 2. Verify the amplifier status: Check if the amplifier is turned on. If it is off, turn it on and adjust the volume control to an audible level. 3. Adjust the volume control: If the volume control is set to zero, gradually increase the volume to a suitable level. 4. Check for distorted sound: If the sound is distorted, it may be due to extreme signal conditions. Lower the output level of the amplifier, such as the volume, bass control, or bass boost, to reduce the distortion. By following these steps, you can troubleshoot the issue of no sound coming from the Pioneer S-ES21-LR-K speaker.

How do I properly position the Pioneer S-ES21-LR-K speaker for optimal sound quality?

To properly position the Pioneer S-ES21-LR-K speaker for optimal sound quality, follow these steps: 1. Determine the listening distance: Measure the distance between the speakers and the primary listening position. This distance should be approximately equal to the distance between the speakers themselves. 2. Angle the speakers: Angle the speakers inward towards the listener. This helps improve the image stability, especially for listeners who are not in the central position. 3. Consider proximity to walls: The speakers can be placed in close proximity to a side or rear wall to enhance the midbass performance. However, be cautious not to place them too close, particularly in a corner, as this may result in unnaturally high bass and degraded image performance. 4. Avoid obstructions: Ensure that there are no obstructions blocking the sound path between the speakers and the listening area. Objects in the way can interfere with the sound quality and imaging. By following these steps, you can position the Pioneer S-ES21-LR-K speaker optimally for the best sound quality.

What are the recommended settings for the Pioneer S-ES21-LR-K speaker to achieve the best audio performance?

To achieve the best audio performance with the Pioneer S-ES21-LR-K speaker, follow these recommended settings: 1. Amplifier Settings: Before connecting the speakers, refer to your amplifier's instruction manual to select the appropriate speaker setting. Set the front speakers to "Large" in the amplifier settings. 2. Speaker Connections: Ensure that all equipment is turned off before making any connections. Connect the red marked speaker cord to the red (+) terminal on the amplifier and the corresponding red (+) terminal on the rear of the speaker. Connect the other cord to the black (-) terminal on both the amplifier and the speaker. 3. Securing the Front Speakers: To securely support the speaker on the wall, pass a reinforced string through the plastic catch and tie it to the wall. Make sure the wall is strong enough to support the weight of the speaker. 4. Placement and Fine Tuning: Separate the speakers at a distance approximately equal to the listening distance. Angle the speakers inward towards the listener for improved image stability. Consider placing the speakers in close proximity to a side or rear wall to enhance midbass performance, but avoid placing them too close to corners to prevent unnatural bass and degraded image performance. By following these recommended settings, you can optimize the audio performance of the Pioneer S-ES21-LR-K speaker.

Why is the Pioneer S-ES21-LR-K speaker producing distorted sound?

The Pioneer S-ES21-LR-K speaker may produce distorted sound due to extreme signal conditions. To address this issue, follow these steps: 1. Turn down the output level of the amplifier: Lower the volume, bass control, or bass boost settings on the amplifier to reduce the signal level. This can help prevent distortion caused by excessive input. 2. Check the amplifier's output impedance: Ensure that the amplifier is designed to work with an 8 Ω load impedance, as specified for the Pioneer S-ES21-LR-K speaker. Using an amplifier with a different impedance may result in distorted sound. 3. Avoid using tone controls excessively: If you are using tone controls to emphasize high or low frequencies, be cautious not to set them too high. Excessive amplification of certain frequencies can lead to distortion. By following these steps, you can address the issue of distorted sound and optimize the audio performance of the Pioneer S-ES21-LR-K speaker.

Is the manual of the Pioneer S-ES21-LR-K available in English?

Yes, the manual of the Pioneer S-ES21-LR-K is available in English .

Is your question not listed? Ask your question here

No results