Pioneer Elite VSX-45 manual

Pioneer Elite VSX-45
8.9 · 2
PDF manual
 · 143 pages
English
manualPioneer Elite VSX-45
62

Basic Setup

05
3 Press MAIN RECEIVER to switch the remote control to the receiver operation mode.
4 Select the parameters you want to set.
When the speaker system is not 7.2ch/5.2.2ch (VSX-90)/5.2ch (VSX-45), set Speaker System before measuring
full auto MCACC. For details, see Speaker system setting on page 110 .
! Speaker System – Shows the current settings. When this is selected and ENTER is pressed, the speaker
system selection screen appears. Select the proper speaker system, then press RETURN to return.
If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another
room, read through Speaker system setting on page 110 and make sure to connect your speakers as neces-
sary before continuing to step 4.
! EQ Type – When you select Expert for Measurement Type, set the correction method of the frequency char-
acteristics of the viewing environment. Usually, set SYMMETRY. For details, see Automatic MCACC (Expert)
on page 103 .
! MCACC – The six MCACC presets are used for storing surround sound settings for different listening posi-
tions. Simply choose an unused preset for now (you can rename it later in Data Management on page 108 ).
! Dolby Enabled Speaker (VSX-90 only) – Select speakers that use Dolby Enabled Speaker (TMd). When Dolby
Enabled Speaker is not used, select NO (page 25 ).
! SP to ceiling (VSX-90 only) – When using the Dolby Enabled Speaker, you can input the vertical distance from
the speaker to the ceiling (page 25 ).
! Measurement Type – When Basic is set, the minimum required measurement is performed in a short period
of time. When Expert is set, accurate and precise measurement is performed so it will take some time.
5 Select ‘START’, then press ENTER.
6 Follow the instructions on-screen.
Make sure the microphone is connected, and if you’re using a subwoofer, make sure it is switched on and set to a
comfortable volume level.
7 Wait for the test tones to finish, then confirm the speaker configuration in the GUI screen.
A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present
in your setup. Try to be as quiet as possible while it’s doing this.
If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed,
the Full Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press
ENTER in step 7.
! With error messages (such as Too much ambient noise! or Check microphone.), select RETRY after check-
ing for ambient noise (see Problems when using the Auto MCACC Setup on page 62 ) and verifying the mic
connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.
Now Analyzing... 2/9
Environment Check
Ambient Noise : OK
Microphone :
Speaker YES/NO :
L : YES
C : YES
R : YES
TMdR : YES
SR : YES
SBR : YES
SBL : YES
SL : YES
TMdL : YES
SW : YES
OK RETRY
Exit
2a.Full Auto MCACC
Return
Exit
2a.Full Auto MCACC
Return
The configuration shown on-screen should reflect the actual speakers you have.
! If you see an ERR message (or the speaker configuration displayed isn’t correct), there may be a problem
with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker con-
nections. If there doesn’t seem to be a problem, you can simply use i/j to select the speaker and k/l to
change the setting and continue.
! If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the
phase (dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are
properly connected.
If Reverse Phase is displayed, the speaker’s wiring (+ and –) may be inverted. Check the speaker
connections.
If the connections were wrong, turn off the power, disconnect the power cord, then reconnect properly.
After this, perform the Full Auto MCACC procedure again.
If the connections were right, select GO NEXT and continue.
8 Make sure ‘OK’ is selected, then press ENTER.
A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum
receiver settings.
Again, try to be as quiet as possible while this is happening. It may take 3 to 10 minutes.
9 The Full Auto MCACC Setup procedure is completed and the Home Menu menu reappears
automatically.
Be sure to disconnect the microphone from this receiver upon completion of the Full Auto MCACC Setup.
The settings made in the Full Auto MCACC Setup should give you excellent surround sound from your system,
but it is also possible to adjust these settings manually using The MCACC PRO (VSX-90)/Advanced MCACC (VSX-
45) menu on page 102 or The System Setup and Other Setup menus on page 109 .
! Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12
cm (5 inches) will end up with different size settings. You can correct the setting manually using the Manual
speaker setup on page 110 .
! The subwoofer distance setting may be farther than the actual distance from the listening position. This set-
ting should be accurate (taking delay and room characteristics into account) and generally does not need to
be changed.
! If Full Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and view-
ing environment, we recommend adjusting the settings manually.
! VSX-90 only: The Dolby Enabled Speaker distance indicates the distance of the ceiling reflection. Therefore, it
is longer than the direct distance but you do not need to change this (page 25 ).
! VSX-90 only: When Full Auto MCACC or Auto MCACC is selected, all of the EQ adjustment values for Dolby
Enabled Speaker are set to 0 dB. You can adjust the settings manually.
Problems when using the Auto MCACC Setup
If the room environment is not optimal for the Auto MCACC Setup (too much background noise, echo off the
walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for
household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them
off if necessary. If there are any instructions showing in the front panel display, please follow them.
! Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off
the TV when doing the Auto MCACC Setup.
The Input Setup menu
You only need to make settings in the Input Setup menu if you didn’t hook up your digital equipment according
to the default settings (see Input function default and possible settings on page 63 ). In this case, you need to
tell the receiver what equipment is hooked up to which terminal so the buttons on the remote control correspond
to the components you’ve connected.
! With factory default settings, the on-screen display will be output from all HDMI output terminals and dis-
played on any TV connected via HDMI cable.
VSX-90 only: You can change where the screen is output in the MAIN/HDZONE (page 114 ) and HDMI output
(page 92 ) settings.
 

View the manual for the Pioneer Elite VSX-45 here, for free. This manual comes under the category receivers and has been rated by 2 people with an average of a 8.9. This manual is available in the following languages: English. Do you have a question about the Pioneer Elite VSX-45 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 5
P
Phillip SavageSeptember 21, 2023

Good morning, I am Savage by name. I was just thought a pioneer vsx 45 elite from Best buy I don't know if it was on sale close out or clearing but it did not come with a remote, how do I make it work?

Good morning, I am Savage by name. I was just thought a pioneer vsx 45 elite from Best buy I don't know if it was on sale clo...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 19, 2023

To operate the Pioneer Elite VSX-45 receiver without a remote control, you can follow these steps: 1. Press the "NET" button on the receiver to switch the remote control to the network operation mode. 2. Use the available buttons on the receiver to control the basic playback functions. Note that some buttons may not be available depending on the category being played back. 3. If you wish to control the receiver from a different location or if the receiver is kept in a closed cabinet, you can connect an optional IR receiver (such as a Niles or Xantech unit) to the IR IN jack on the rear of the receiver. This will allow you to control the receiver using the IR receiver instead of the remote sensor on the front panel. 4. If you have other components connected to the receiver, you can use the 12 volt trigger feature to switch them on or off when you select an input function. To set up the 12 volt trigger, refer to the Input Setup menu. 5. Make sure to plug in the receiver after connecting all your components, including the speakers. Handle the power cord properly and avoid pulling it by tugging the cord or touching it with wet hands.

This answer is automatically generated
J
Jody Metz May 3, 2023

My vsx-45 elite amp doesn't work at all and blue light on front is blinking. What's wrong with it

R
Robert SnodgrassFebruary 25, 2023

I need some help getting sound to come from my PIONEER VSX45. Its connected to a Bravia Sony TV and the tv speakers work fine. Im missing something in the receiver set up...

F
Frank SalinasJune 22, 2023

TV Sound works but the receiver speaker can't be heard. Receiver power works

1 comment
M
Mark E DiazJanuary 24, 2024

@Frank Salinas I have a vsx 45 and I use an optical cable from the vsx 45 to my Samsung tv and switch the vsx 45 to tv and it works fine.

D
DavidAugust 10, 2022

How to fix the vlf off buttom so I can get sound again?

The Pioneer Elite VSX-45 is a receiver that offers a range of features for audio enthusiasts. It is designed to deliver high-quality sound and provide a seamless audio experience. The Pioneer Elite VSX-45 is equipped with integrated Bluetooth technology, allowing users to easily connect and stream music from compatible devices. It also supports a variety of audio formats, including Dolby TrueHD and DTS-HD Master Audio, for a more immersive listening experience. This receiver features a 5.2 channel configuration, providing ample power and flexibility for setting up a home theater system. With its 80 watts per channel, it can deliver clear and balanced audio, enhancing the overall cinematic experience. The Pioneer Elite VSX-45 includes several connectivity options, including HDMI inputs and outputs, allowing for seamless integration with other multimedia devices. Additionally, it features built-in Wi-Fi and AirPlay compatibility, providing convenient wireless streaming options. This receiver also includes advanced audio calibration technology, such as Pioneer's Multi-Channel Acoustic Calibration System (MCACC), which automatically adjusts and optimizes the audio settings based on the room's acoustics. The Pioneer Elite VSX-45 boasts a sleek and modern design, with a user-friendly interface that makes it easy to navigate through its various settings and features. Overall, the Pioneer Elite VSX-45 offers a high-quality audio experience, with its advanced features and connectivity options making it a versatile receiver for discerning audio enthusiasts.

General
BrandPioneer
ModelElite VSX-45
Productreceiver
EAN0884938290814
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer Elite VSX-45 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

How can I properly connect my audio sources to the Pioneer Elite VSX-45 receiver?

To connect your audio sources, locate the audio input ports on the back of the receiver, ensure that the corresponding cables are securely plugged into the correct ports, and then adjust the input settings on the receiver accordingly for each source.

How do I adjust the audio settings on the Pioneer Elite VSX-45 receiver?

To adjust the audio settings, use the navigation buttons on the remote control or the front panel of the receiver to access the settings menu. From there, you can modify parameters such as bass, treble, balance, and surround sound options to personalize your audio experience.

What is the recommended speaker setup for the Pioneer Elite VSX-45 receiver?

For optimal sound quality, it is advised to follow the recommended speaker setup guidelines in the manual. This typically includes placing the main speakers at ear level, ensuring appropriate distance and positioning for the surround speakers, and setting up a dedicated subwoofer to enhance low-frequency performance.

How do I calibrate the room acoustics with the Pioneer Elite VSX-45 receiver?

To calibrate the room acoustics, you can utilize the built-in automatic speaker calibration feature, such as Pioneer's MCACC system. Follow the on-screen instructions and connect the included microphone to the receiver, which will measure and analyze the audio characteristics of your room to optimize the sound output.

How can I troubleshoot common issues with the Pioneer Elite VSX-45 receiver?

Troubleshooting common issues involves checking the connections, ensuring proper speaker wire polarity, and verifying that all equipment is powered on and set to the correct input/output settings. Additionally, you can perform a factory reset or consult the troubleshooting section of the manual for specific issues such as audio dropouts, remote control problems, or network connectivity concerns.

Is the manual of the Pioneer Elite VSX-45 available in English?

Yes, the manual of the Pioneer Elite VSX-45 is available in English .

Is your question not listed? Ask your question here

No results