Pioneer Elite VSX-45 manual

Pioneer Elite VSX-45
8.9 · 2
PDF manual
 · 143 pages
English
manualPioneer Elite VSX-45
122
FAQ
14
HDMI
Symptom Remedy
The HDMI indicator blinks continu-
ously.
Check all the points below.
Video/audio is not output or is inter-
rupted.
This receiver is HDCP-compatible. Check that the components you are connecting are
also HDCP-compatible. If they are not, please connect them using the component or
composite video jacks.
Depending on the connected source component, it’s possible that it will not work with
this receiver (even if it is HDCP-compatible). In this case, connect using the component
or composite video jacks between source and receiver.
If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.
If video images do not appear on your TV, try adjusting the resolution, Deep Color or other
setting for your component.
While analog video signals are being output over HDMI, use a separate connection for
audio output.
To output signals in Deep Color, use an HDMI cable (High Speed HDMI
®
/
TM
Cable) to
connect this receiver to a component or TV with the Deep Color feature.
The picture and sound output get cut
off, or there is no output produced.
Influence from a TV whose power is set to standby may cause the picture or sound output
to not be produced or to get cut off. In this case, press OUT P., and make sure to use an
output other than the HDMI output to which that TV is connected.
No picture.
Try changing the SCAL setting (in Setting the Video options on page 91 ).
VSX-90 only: To use the HDMI OUT 2 terminal in the main zone, set the MAIN/HDZONE
Output Setting to MAIN (page 114 ).
No sound, or sound suddenly
ceases.
Check that the HDMI Audio setting is set to AMP (Setting the Audio options on page 89 ).
If the component is a DVI device, use a separate connection for the audio.
If analog video is being output over HDMI, please use a separate connection for the
audio.
Check the audio output settings of the source component.
HDMI format digital audio transmissions require a longer time to be recognized. Due
to this, interruption in the audio may occur when switching between audio formats or
beginning playback.
Turning on/off the device connected to this unit’s HDMI OUT terminal during playback,
or disconnecting/connecting the HDMI cable during playback, may cause noise or inter-
rupted audio.
Noisy or distorted picture. Sometimes a video deck may output a noisy video signal (during scanning, for example),
or the video quality may just be poor (with some video game units, for example). The
picture quality may also depend on the settings, etc. of your display device. Switch off
the video converter and reconnect the source and display device using the same type of
connection (component or composite), then start playback again.
If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.
Symptom Remedy
Synchronized operation not possible
using Control with HDMI function.
Check the HDMI connections.
The cable may be damaged.
Select ON for the Control Mode with HDMI setting (see HDMI Setup on page 86 ).
Turn the TV’s power on before turning on this receiver’s power.
Set the TV side Control with HDMI setting to on (see TV’s operating instructions).
VSX-90 only: Connect the TV to the HDMI OUT 1 terminal and set the HDMI output to
OUT 1. Then turn on first the TV’s power, then this receiver’s power.
VSX-90 only: When HDZONE is set to
ON, the video resolution and number
of audio channels for the main zone
side changes.
This is due to the HDMI connection specifications; it is not a malfunction. When play-
ing the same input in the main zone and HDZONE, video and audio signals that can be
output in common for all the devices connected to the HDMI OUT 1 and HDMI OUT 2
(HDZONE) terminals are set.
VSX-90 only: HDZONE cannot be
turned on.
Set Output Setting at MAIN/HDZONE to HDZONE (page 114 ).
VSX-90 only: When the input source
for the main or HDZONE is switched
or when the power of the respective
zones is turned on and off, the audio
or video of the HDMI output terminal
that is not being operated is some-
times interrupted.
This is because the HDMI devices need to recognize each other again. This is not a
malfunction. If the picture is disturbed or not displayed, turn off the power of the devices
in all the zones, then try again. Also try temporarily turning the Network Standby and
Standby Through settings OFF.
VSX-90 only: Such menus as the
HOME MENU as well as the on-
screen display are not displayed for
HDMI OUT 1 or HDMI OUT 2.
Press OUT P. and switch the HDMI OUT 1/2 setting.
Cannot upscale to 4K.
Change SCAL. (page 91 )
VSX-90 only: 4K video is not output
even though a 4K compliant TV is
connected.
When the MAIN/HDZONE setting is MAIN and the HDMI output setting is OUT 1+2 and
when the MAIN/HDZONE setting is HDZONE and HDZONE is the same input as with the
main zone, video is output with the lower resolution of the TV connected to HDMI OUT 1
and HDMI OUT 2. When there is only one 4K compliant TV, connect it to HDMI OUT 1
and set the HDMI output setting to OUT 1 or turn off HDZONE so that video is only output
to the 4K compliant TV.
Even though a 4K/60p 4:4:4 24 bit
compatible TV is connected, the
4K/60p 4:4:4 24 bit video image is not
output correctly.
Set the HDMI 4K/60p signal output setting to 4:4:4 (page 92 ).
When the HDMI cable does not support 4K/60p 4:4:4 24 bit (18 Gbps transmission),
video images may not be output properly. In that case, replace the cable with a compat-
ible HDMI cable or change the HDMI 4K/60p signal output setting to 4:2:0 to watch the
4K/60p 4:2:0 24 bit video image.
VSX-90 only: The HDMI OUT 2 terminal does not output a 4K/60p 4:4:4 24 bit video image
if MAIN/HDZONE is set to HDZONE. Set MAIN/HDZONE to MAIN or use the HDMI OUT
1 terminals.
You cannot input 4K/60p 4:4:4 24 bit video from HDMI IN 3 to the IN 5 terminal and HDMI
IN 6 terminal (VSX-90 only). Use the BD IN, HDMI IN 1 or HDMI IN 2 terminal.
 

View the manual for the Pioneer Elite VSX-45 here, for free. This manual comes under the category receivers and has been rated by 2 people with an average of a 8.9. This manual is available in the following languages: English. Do you have a question about the Pioneer Elite VSX-45 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 5
P
Phillip SavageSeptember 21, 2023

Good morning, I am Savage by name. I was just thought a pioneer vsx 45 elite from Best buy I don't know if it was on sale close out or clearing but it did not come with a remote, how do I make it work?

Good morning, I am Savage by name. I was just thought a pioneer vsx 45 elite from Best buy I don't know if it was on sale clo...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 19, 2023

To operate the Pioneer Elite VSX-45 receiver without a remote control, you can follow these steps: 1. Press the "NET" button on the receiver to switch the remote control to the network operation mode. 2. Use the available buttons on the receiver to control the basic playback functions. Note that some buttons may not be available depending on the category being played back. 3. If you wish to control the receiver from a different location or if the receiver is kept in a closed cabinet, you can connect an optional IR receiver (such as a Niles or Xantech unit) to the IR IN jack on the rear of the receiver. This will allow you to control the receiver using the IR receiver instead of the remote sensor on the front panel. 4. If you have other components connected to the receiver, you can use the 12 volt trigger feature to switch them on or off when you select an input function. To set up the 12 volt trigger, refer to the Input Setup menu. 5. Make sure to plug in the receiver after connecting all your components, including the speakers. Handle the power cord properly and avoid pulling it by tugging the cord or touching it with wet hands.

This answer is automatically generated
J
Jody Metz May 3, 2023

My vsx-45 elite amp doesn't work at all and blue light on front is blinking. What's wrong with it

R
Robert SnodgrassFebruary 25, 2023

I need some help getting sound to come from my PIONEER VSX45. Its connected to a Bravia Sony TV and the tv speakers work fine. Im missing something in the receiver set up...

F
Frank SalinasJune 22, 2023

TV Sound works but the receiver speaker can't be heard. Receiver power works

1 comment
M
Mark E DiazJanuary 24, 2024

@Frank Salinas I have a vsx 45 and I use an optical cable from the vsx 45 to my Samsung tv and switch the vsx 45 to tv and it works fine.

D
DavidAugust 10, 2022

How to fix the vlf off buttom so I can get sound again?

The Pioneer Elite VSX-45 is a receiver that offers a range of features for audio enthusiasts. It is designed to deliver high-quality sound and provide a seamless audio experience. The Pioneer Elite VSX-45 is equipped with integrated Bluetooth technology, allowing users to easily connect and stream music from compatible devices. It also supports a variety of audio formats, including Dolby TrueHD and DTS-HD Master Audio, for a more immersive listening experience. This receiver features a 5.2 channel configuration, providing ample power and flexibility for setting up a home theater system. With its 80 watts per channel, it can deliver clear and balanced audio, enhancing the overall cinematic experience. The Pioneer Elite VSX-45 includes several connectivity options, including HDMI inputs and outputs, allowing for seamless integration with other multimedia devices. Additionally, it features built-in Wi-Fi and AirPlay compatibility, providing convenient wireless streaming options. This receiver also includes advanced audio calibration technology, such as Pioneer's Multi-Channel Acoustic Calibration System (MCACC), which automatically adjusts and optimizes the audio settings based on the room's acoustics. The Pioneer Elite VSX-45 boasts a sleek and modern design, with a user-friendly interface that makes it easy to navigate through its various settings and features. Overall, the Pioneer Elite VSX-45 offers a high-quality audio experience, with its advanced features and connectivity options making it a versatile receiver for discerning audio enthusiasts.

General
BrandPioneer
ModelElite VSX-45
Productreceiver
EAN0884938290814
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer Elite VSX-45 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

How can I properly connect my audio sources to the Pioneer Elite VSX-45 receiver?

To connect your audio sources, locate the audio input ports on the back of the receiver, ensure that the corresponding cables are securely plugged into the correct ports, and then adjust the input settings on the receiver accordingly for each source.

How do I adjust the audio settings on the Pioneer Elite VSX-45 receiver?

To adjust the audio settings, use the navigation buttons on the remote control or the front panel of the receiver to access the settings menu. From there, you can modify parameters such as bass, treble, balance, and surround sound options to personalize your audio experience.

What is the recommended speaker setup for the Pioneer Elite VSX-45 receiver?

For optimal sound quality, it is advised to follow the recommended speaker setup guidelines in the manual. This typically includes placing the main speakers at ear level, ensuring appropriate distance and positioning for the surround speakers, and setting up a dedicated subwoofer to enhance low-frequency performance.

How do I calibrate the room acoustics with the Pioneer Elite VSX-45 receiver?

To calibrate the room acoustics, you can utilize the built-in automatic speaker calibration feature, such as Pioneer's MCACC system. Follow the on-screen instructions and connect the included microphone to the receiver, which will measure and analyze the audio characteristics of your room to optimize the sound output.

How can I troubleshoot common issues with the Pioneer Elite VSX-45 receiver?

Troubleshooting common issues involves checking the connections, ensuring proper speaker wire polarity, and verifying that all equipment is powered on and set to the correct input/output settings. Additionally, you can perform a factory reset or consult the troubleshooting section of the manual for specific issues such as audio dropouts, remote control problems, or network connectivity concerns.

Is the manual of the Pioneer Elite VSX-45 available in English?

Yes, the manual of the Pioneer Elite VSX-45 is available in English .

Is your question not listed? Ask your question here

No results