Pioneer Elite VSX-45 manual

Pioneer Elite VSX-45
8.9 · 2
PDF manual
 · 143 pages
English
manualPioneer Elite VSX-45
119
FAQ
14
Symptom Remedy
No sound is output when an input
function is selected.
Turn the volume up to approx. –30 dB.
Check that the speaker selector setting is set to OFF (page 91 ).
Make sure the correct input function is selected.
Make sure the correct input signal is selected (see Choosing the input signal on page
76 ).
Check that the source equipment is correctly connected (Refer to page 20 (VSX-90) or
page 39 (VSX-45)).
Check that the speakers are connected properly (see Connecting the speakers on page
24 ).
No sound from the surround or
center speakers.
Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t
selected; select one of the surround listening modes (see Enjoying various types of play-
back using the listening modes on page 74 ).
Check that the surround/center speakers are not set to NO (see Speaker Setting on page
111 ).
Check the speaker connections (see Connecting the speakers on page 24 ).
VSX-90 only: No sound from surround
back speakers.
Check that the surround back speakers are set to LARGE or SMALL, and the surround
speakers are not set to NO (see Speaker Setting on page 111 ).
Check the speaker connections (see Connecting the speakers on page 24 ). If only
one surround back speaker is connected, make sure it’s connected to the left channel
speaker terminal.
When Speaker System is set to 7.2ch/5.2.2ch and SP: TMd ON is selected with the
OUT P. button, no sound will be output from the surround back speakers. Select SP:
SB ON or SP: SB/TMd ON (see Switching the speaker terminals on page 91 ).
When Speaker System is set to 7.2ch SB/FW and SP: FW ON is selected with the OUT P.
button, no sound will be output from the surround back speakers. Select SP: SB ON or
SP: SB/FW ON (see Switching the speaker terminals on page 91 ).
When Dolby Surround is selected, audio is not output from the surround back speaker
when it is the only one connected (set).
VSX-90 only: No sound from front
wide speakers.
Check that the front wide speakers are set to LARGE or SMALL, and the surround speak-
ers are not set to NO (see Speaker Setting on page 111 ).
Check the speaker connections (see Connecting the speakers on page 24 ).
When Speaker System is set to 7.2ch SB/FW and SP: SB ON is selected with the OUT P.
button, no sound will be output from the front wide speakers. Select SP: FW ON or SP:
SB/FW ON (see Switching the speaker terminals on page 91 ).
When Speaker System is set to 7.2ch SB/FW and Dolby Surround is selected, audio is
not output from the front wide speakers.
No sound from subwoofer. Check that the subwoofer is connected properly, switched on and the volume turned up.
If your subwoofer has a sleep function, make sure it is switched off.
Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 111 ).
The crossover frequency may be set too low; try setting it higher to match the characteris-
tics of your other speakers (see Speaker Setting on page 111 ).
If there is very little low frequency information in the source material, change your
speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(see Speaker Setting on page 111 ).
Check that the LFE channel is not set to OFF, or to a very quiet setting (see Setting the
Audio options on page 89 ).
Check the speaker level settings (see Channel Level on page 112 ).
Symptom Remedy
No sound from one speaker. Check the speaker connection (see Connecting the speakers on page 24 ).
Check the speaker level settings (see Channel Level on page 112 ).
Check that the speaker hasn’t been set to NO (see Speaker Setting on page 111 ).
The channel may not be recorded in the source. By using one of the advanced effect
listening modes, you may be able to create the missing channel (see Enjoying various
types of playback using the listening modes on page 74 ).
No digital sound is output.
Make sure that the digital input is assigned correctly for the input jack the component is
connected to (see The Input Setup menu on page 62 ).
Check the digital output settings on the source component.

Other audio problems

Symptom Remedy
Broadcast stations cannot be
selected automatically, or there is
considerable noise in radio broad-
casts.
Fully extend the FM wire antenna, adjust the position for best reception and secure to a
wall, etc.
Use an outdoor antenna for better reception (see pages 33 , 48 ).
Adjust the position and direction of the AM antenna.
Noise may be caused by interference from other equipment, such as a fluorescent light,
motor, etc. Switch off or move the other equipment, or move the AM antenna.
Subwoofer output is very low.
To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL
(see Speaker Setting on page 111 ).
Everything seems to be set up cor-
rectly, but the playback sound is odd.
The speakers may be out of phase. Check that the positive/negative speaker terminals on
the receiver are matched with the corresponding terminals on the speakers (see Con-
necting the speakers on page 24 ).
The Phase Control feature doesn’t
seem to have an audible effect.
If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass
cutoff is set to the highest frequency setting. If there is a PHASE setting on your sub-
woofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the
best overall effect on the sound).
Make sure the speaker distance setting is correct for all speakers (see Speaker Distance
on page 112 ).
Can’t select some Input functions
by the INPUT SELECTOR on the
front panel or the ALL button on the
remote control.
Check the Input Skip settings in the Input Setup menu (see The Input Setup menu on
page 62 ).
Check the HDMI Input assignment in the Input Setup menu then try OFF (see The Input
Setup menu on page 62 ).
There seems to be a time lag
between the speakers and the output
of the subwoofer.
See Automatically conducting optimum sound tuning (Full Auto MCACC) on page 61
to set up your system again using MCACC (this will automatically compensate for a delay
in the subwoofer output).
The maximum volume available
(shown in the front panel display) is
lower than the +12dB maximum.
Check that the Volume Limit is set to OFF (see Volume Setup on page 113 ).
The channel level setting may be over 0.0dB.
Certain listening modes or
HOME MENU items cannot be
selected.
Some functions cannot be selected, depending on the input signal and listening mode.
The volume level drops automati-
cally.
The temperature within the unit has exceeded the allowable value. Try moving the unit for
better ventilation (see Installing the receiver on page 11 ).
Volume seems different when input
is switched.
Set the Channel Level setting to ALL, then adjust the volume of the respective input
sources (see Input Volume Absorber on page 92 ).
 

View the manual for the Pioneer Elite VSX-45 here, for free. This manual comes under the category receivers and has been rated by 2 people with an average of a 8.9. This manual is available in the following languages: English. Do you have a question about the Pioneer Elite VSX-45 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 5
P
Phillip SavageSeptember 21, 2023

Good morning, I am Savage by name. I was just thought a pioneer vsx 45 elite from Best buy I don't know if it was on sale close out or clearing but it did not come with a remote, how do I make it work?

Good morning, I am Savage by name. I was just thought a pioneer vsx 45 elite from Best buy I don't know if it was on sale clo...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 19, 2023

To operate the Pioneer Elite VSX-45 receiver without a remote control, you can follow these steps: 1. Press the "NET" button on the receiver to switch the remote control to the network operation mode. 2. Use the available buttons on the receiver to control the basic playback functions. Note that some buttons may not be available depending on the category being played back. 3. If you wish to control the receiver from a different location or if the receiver is kept in a closed cabinet, you can connect an optional IR receiver (such as a Niles or Xantech unit) to the IR IN jack on the rear of the receiver. This will allow you to control the receiver using the IR receiver instead of the remote sensor on the front panel. 4. If you have other components connected to the receiver, you can use the 12 volt trigger feature to switch them on or off when you select an input function. To set up the 12 volt trigger, refer to the Input Setup menu. 5. Make sure to plug in the receiver after connecting all your components, including the speakers. Handle the power cord properly and avoid pulling it by tugging the cord or touching it with wet hands.

This answer is automatically generated
J
Jody Metz May 3, 2023

My vsx-45 elite amp doesn't work at all and blue light on front is blinking. What's wrong with it

R
Robert SnodgrassFebruary 25, 2023

I need some help getting sound to come from my PIONEER VSX45. Its connected to a Bravia Sony TV and the tv speakers work fine. Im missing something in the receiver set up...

F
Frank SalinasJune 22, 2023

TV Sound works but the receiver speaker can't be heard. Receiver power works

1 comment
M
Mark E DiazJanuary 24, 2024

@Frank Salinas I have a vsx 45 and I use an optical cable from the vsx 45 to my Samsung tv and switch the vsx 45 to tv and it works fine.

D
DavidAugust 10, 2022

How to fix the vlf off buttom so I can get sound again?

The Pioneer Elite VSX-45 is a receiver that offers a range of features for audio enthusiasts. It is designed to deliver high-quality sound and provide a seamless audio experience. The Pioneer Elite VSX-45 is equipped with integrated Bluetooth technology, allowing users to easily connect and stream music from compatible devices. It also supports a variety of audio formats, including Dolby TrueHD and DTS-HD Master Audio, for a more immersive listening experience. This receiver features a 5.2 channel configuration, providing ample power and flexibility for setting up a home theater system. With its 80 watts per channel, it can deliver clear and balanced audio, enhancing the overall cinematic experience. The Pioneer Elite VSX-45 includes several connectivity options, including HDMI inputs and outputs, allowing for seamless integration with other multimedia devices. Additionally, it features built-in Wi-Fi and AirPlay compatibility, providing convenient wireless streaming options. This receiver also includes advanced audio calibration technology, such as Pioneer's Multi-Channel Acoustic Calibration System (MCACC), which automatically adjusts and optimizes the audio settings based on the room's acoustics. The Pioneer Elite VSX-45 boasts a sleek and modern design, with a user-friendly interface that makes it easy to navigate through its various settings and features. Overall, the Pioneer Elite VSX-45 offers a high-quality audio experience, with its advanced features and connectivity options making it a versatile receiver for discerning audio enthusiasts.

General
BrandPioneer
ModelElite VSX-45
Productreceiver
EAN0884938290814
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer Elite VSX-45 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

How can I properly connect my audio sources to the Pioneer Elite VSX-45 receiver?

To connect your audio sources, locate the audio input ports on the back of the receiver, ensure that the corresponding cables are securely plugged into the correct ports, and then adjust the input settings on the receiver accordingly for each source.

How do I adjust the audio settings on the Pioneer Elite VSX-45 receiver?

To adjust the audio settings, use the navigation buttons on the remote control or the front panel of the receiver to access the settings menu. From there, you can modify parameters such as bass, treble, balance, and surround sound options to personalize your audio experience.

What is the recommended speaker setup for the Pioneer Elite VSX-45 receiver?

For optimal sound quality, it is advised to follow the recommended speaker setup guidelines in the manual. This typically includes placing the main speakers at ear level, ensuring appropriate distance and positioning for the surround speakers, and setting up a dedicated subwoofer to enhance low-frequency performance.

How do I calibrate the room acoustics with the Pioneer Elite VSX-45 receiver?

To calibrate the room acoustics, you can utilize the built-in automatic speaker calibration feature, such as Pioneer's MCACC system. Follow the on-screen instructions and connect the included microphone to the receiver, which will measure and analyze the audio characteristics of your room to optimize the sound output.

How can I troubleshoot common issues with the Pioneer Elite VSX-45 receiver?

Troubleshooting common issues involves checking the connections, ensuring proper speaker wire polarity, and verifying that all equipment is powered on and set to the correct input/output settings. Additionally, you can perform a factory reset or consult the troubleshooting section of the manual for specific issues such as audio dropouts, remote control problems, or network connectivity concerns.

Is the manual of the Pioneer Elite VSX-45 available in English?

Yes, the manual of the Pioneer Elite VSX-45 is available in English .

Is your question not listed? Ask your question here

No results