Pioneer Elite VSX-45 manual

Pioneer Elite VSX-45
8.9 · 2
PDF manual
 · 143 pages
English
manualPioneer Elite VSX-45
118
FAQ
14

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate
the other components and electrical appliances being used. If the trouble cannot be rectified even after exercis-
ing the checks listed below, ask your nearest Pioneer authorized independent service company to carry out repair work.
! If the unit does not operate normally due to external effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal operating conditions.If the problem is not solved after the troubleshooting below, if the screen freezes unexpectedly or if the buttons on the remote control or front panel stop working completely, do the following:
! Press u STANDBY/ON on the front panel to turn off the power, then turn the power back on.
If this does not solve the problem, turn off the power again, then press and hold the u STANDBY/ON button
on the front panel for at least five seconds. (The power turns on, then turns off after five seconds.)
! If the power cannot be turned off, press and hold u STANDBY/ON on the front panel for over five seconds. The
power will turn off. In this case, the various settings made on the receiver may be cleared.

Power

Symptom Remedy
The power does not turn on. Make sure that the power cord is plugged in to an active power outlet.
Try disconnecting from the power outlet, then plugging back in.
Power automatically turns off.
When Auto Power Down is set, the power automatically turns off at the set time (page
113 ).
When the power is turned on, the
WIRELESS indicator slowly flashes.
After unpacking, turning on the power, and returning to initial factory settings (page 95
), the WIRELESS indicator slowly flashes. This is not a malfunction.
This receiver is designed to automatically enter WAC mode when turning on the power of
this receiver in the initial factory settings state. For details about WAC mode, please refer
to page 57 . After the network settings (page 55 ) have been completed, the WIRELESS
indicator flashing disappears.
When the network is not connected, even though the WIRELESS indicator is blinking,
there is no problem using it in this state.
VSX-90 only: Power cannot be turned
off. (ZONE 2 ON is displayed.)
Press the Z2 button on the remote control for 1.5 seconds and then press the
u STANDBY/ON button to turn OFF the power.
VSX-90 only: Power cannot be turned
off. (HDZONE ON is displayed.)
Press the HDZ button on the remote control for 1.5 seconds and then press the
u STANDBY/ON button to turn OFF the power.
The receiver suddenly switches off or
the WIRELESS indicator blinks.
Check that there are no loose strands of speaker wire touching the rear panel or another
set of wires. If so, re-attach the speaker wires, making sure there are no stray strands.
The receiver may have a serious problem. Disconnect from the power and call a Pioneer
authorized independent service company.
Symptom Remedy
During loud playback the power sud-
denly switches off.
Turn down the volume.
Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 105 .
Switch on the digital safety feature. While holding down ENTER on the front panel,
press u STANDBY/ON to set this receiver to the standby mode. Use TUNE i/j to
select D.SAFETY cOFFd, and then use PRESET k/l to select 1 or 2 (select D.SAFETY
cOFFd to deactivate this feature). If the power switches off even with 2 switched on, turn
down the volume. With 1 or 2 on, some features may be unavailable.
If there is very little low frequency information in the source material, change your
speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(see Speaker Setting on page 111 ).
The unit does not respond when the
buttons are pressed.
Try switching the receiver off, then back on again.
Try disconnecting the power cord, then connect again.
AMP ERR is indicated and the main
power turns off. The MCACC PRO
(VSX-90) /Advanced MCACC (VSX-
45) indicator blinks and the main
power does not turn on.
The receiver may have a serious problem. Do not try switching the receiver on. Unplug
the receiver from the wall and call a Pioneer authorized independent service company.
The receiver suddenly switches off or
the FL OFF indicator blinks.
There is a possibility that the power supply circuit of the receiver has failed. Wait at least
one minute and then turn ON the power again. If the same symptom appears again after
turning ON the power again, stop using the receiver, disconnect the power cable and
request repair.
AMP OVERHEAT blinks in the dis-
play and the FL OFF indicator flash
and the power turns off.
Allow the unit to cool down in a well-ventilated place before switching back on (see
Installing the receiver on page 11 ).
Check whether the cables used to connect the speakers are short-circuited.
Wait at least 1 minute, then try turning the power on again.
The temperature within the unit has exceeded the allowablevalue.
Lower the volume level.
The main power suddenly turns
off, and MCACC PRO (VSX-90) /
Advanced MCACC (VSX-45) indica-
tor blinks.
The power unit is damaged. Unplug the receiver from the wall and call a Pioneer autho-
rized independent service company.
Display blinks 12V TRG ERR. An error has arisen in the 12 V trigger jacks. Reconnect accurately then turn the power
back on.

No sound

Symptom Remedy
There is no sound output, the sound
gets cut off, or there is noise present.
If Fixed PCM in audio parameter is set to ON, you will not be able to playback audio in
formats other than PCM audio. For other audio formats than PCM audio, select OFF (See
Setting the Audio options on page 89 ).
 

View the manual for the Pioneer Elite VSX-45 here, for free. This manual comes under the category receivers and has been rated by 2 people with an average of a 8.9. This manual is available in the following languages: English. Do you have a question about the Pioneer Elite VSX-45 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 5
P
Phillip SavageSeptember 21, 2023

Good morning, I am Savage by name. I was just thought a pioneer vsx 45 elite from Best buy I don't know if it was on sale close out or clearing but it did not come with a remote, how do I make it work?

Good morning, I am Savage by name. I was just thought a pioneer vsx 45 elite from Best buy I don't know if it was on sale clo...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 19, 2023

To operate the Pioneer Elite VSX-45 receiver without a remote control, you can follow these steps: 1. Press the "NET" button on the receiver to switch the remote control to the network operation mode. 2. Use the available buttons on the receiver to control the basic playback functions. Note that some buttons may not be available depending on the category being played back. 3. If you wish to control the receiver from a different location or if the receiver is kept in a closed cabinet, you can connect an optional IR receiver (such as a Niles or Xantech unit) to the IR IN jack on the rear of the receiver. This will allow you to control the receiver using the IR receiver instead of the remote sensor on the front panel. 4. If you have other components connected to the receiver, you can use the 12 volt trigger feature to switch them on or off when you select an input function. To set up the 12 volt trigger, refer to the Input Setup menu. 5. Make sure to plug in the receiver after connecting all your components, including the speakers. Handle the power cord properly and avoid pulling it by tugging the cord or touching it with wet hands.

This answer is automatically generated
J
Jody Metz May 3, 2023

My vsx-45 elite amp doesn't work at all and blue light on front is blinking. What's wrong with it

R
Robert SnodgrassFebruary 25, 2023

I need some help getting sound to come from my PIONEER VSX45. Its connected to a Bravia Sony TV and the tv speakers work fine. Im missing something in the receiver set up...

F
Frank SalinasJune 22, 2023

TV Sound works but the receiver speaker can't be heard. Receiver power works

1 comment
M
Mark E DiazJanuary 24, 2024

@Frank Salinas I have a vsx 45 and I use an optical cable from the vsx 45 to my Samsung tv and switch the vsx 45 to tv and it works fine.

D
DavidAugust 10, 2022

How to fix the vlf off buttom so I can get sound again?

The Pioneer Elite VSX-45 is a receiver that offers a range of features for audio enthusiasts. It is designed to deliver high-quality sound and provide a seamless audio experience. The Pioneer Elite VSX-45 is equipped with integrated Bluetooth technology, allowing users to easily connect and stream music from compatible devices. It also supports a variety of audio formats, including Dolby TrueHD and DTS-HD Master Audio, for a more immersive listening experience. This receiver features a 5.2 channel configuration, providing ample power and flexibility for setting up a home theater system. With its 80 watts per channel, it can deliver clear and balanced audio, enhancing the overall cinematic experience. The Pioneer Elite VSX-45 includes several connectivity options, including HDMI inputs and outputs, allowing for seamless integration with other multimedia devices. Additionally, it features built-in Wi-Fi and AirPlay compatibility, providing convenient wireless streaming options. This receiver also includes advanced audio calibration technology, such as Pioneer's Multi-Channel Acoustic Calibration System (MCACC), which automatically adjusts and optimizes the audio settings based on the room's acoustics. The Pioneer Elite VSX-45 boasts a sleek and modern design, with a user-friendly interface that makes it easy to navigate through its various settings and features. Overall, the Pioneer Elite VSX-45 offers a high-quality audio experience, with its advanced features and connectivity options making it a versatile receiver for discerning audio enthusiasts.

General
BrandPioneer
ModelElite VSX-45
Productreceiver
EAN0884938290814
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer Elite VSX-45 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

How can I properly connect my audio sources to the Pioneer Elite VSX-45 receiver?

To connect your audio sources, locate the audio input ports on the back of the receiver, ensure that the corresponding cables are securely plugged into the correct ports, and then adjust the input settings on the receiver accordingly for each source.

How do I adjust the audio settings on the Pioneer Elite VSX-45 receiver?

To adjust the audio settings, use the navigation buttons on the remote control or the front panel of the receiver to access the settings menu. From there, you can modify parameters such as bass, treble, balance, and surround sound options to personalize your audio experience.

What is the recommended speaker setup for the Pioneer Elite VSX-45 receiver?

For optimal sound quality, it is advised to follow the recommended speaker setup guidelines in the manual. This typically includes placing the main speakers at ear level, ensuring appropriate distance and positioning for the surround speakers, and setting up a dedicated subwoofer to enhance low-frequency performance.

How do I calibrate the room acoustics with the Pioneer Elite VSX-45 receiver?

To calibrate the room acoustics, you can utilize the built-in automatic speaker calibration feature, such as Pioneer's MCACC system. Follow the on-screen instructions and connect the included microphone to the receiver, which will measure and analyze the audio characteristics of your room to optimize the sound output.

How can I troubleshoot common issues with the Pioneer Elite VSX-45 receiver?

Troubleshooting common issues involves checking the connections, ensuring proper speaker wire polarity, and verifying that all equipment is powered on and set to the correct input/output settings. Additionally, you can perform a factory reset or consult the troubleshooting section of the manual for specific issues such as audio dropouts, remote control problems, or network connectivity concerns.

Is the manual of the Pioneer Elite VSX-45 available in English?

Yes, the manual of the Pioneer Elite VSX-45 is available in English .

Is your question not listed? Ask your question here

No results