Pioneer Elite SC-91 manual

Pioneer Elite SC-91
9.9 · 1
PDF manual
 · 124 pages
English
manualPioneer Elite SC-91
88
The MCACC PRO menu
11
3 Connect the microphone to the MCACC SETUP MIC jack on the front panel.
Make sure there are no obstacles between the speakers and the microphone.
PHONES
SPEAKERS
MULTI-ZONE
CONTROL
ZONE 2
ON/OFF
MCACC
SETUP MIC
HDMI 5 INPUT
AUTO/ALC/
DIRECT STATUSBAND TUNER EDIT
iPod iPhone
DIRECT CONTROL
5V 1
A
HDZONE
ON/OFF
PHASE
CONTROL
Microphone
Tripod
If you have a tripod, use it to place the microphone so that it’s about ear level at your normal listening position. If
you do not have a tripod, use some other object to install the microphone.
! It may not be possible to measure correctly if the microphone is placed on a table, sofa, etc.
4 When you’re finished setting the options, select START then press ENTER.
5 Follow the instructions on-screen.
6 Wait for the Auto MCACC Setup to finish outputting test tones.
A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present
in your setup. Try to be as quiet as possible while it’s doing this.
! With error messages (such as Too much ambient noise! or Check microphone.), select RETRY after check-
ing for ambient noise (see Problems when using the Auto MCACC Setup on page 48 ) and verifying the mic
connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.
! Do not adjust the volume during the test tones. This may result in incorrect speaker settings.
7 If necessary, confirm the speaker configuration in the GUI screen.
The configuration shown on-screen should reflect the actual speakers you have.
If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed,
the Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press ENTER in
step 8.
! If you see an ERR message (or the speaker configuration displayed isn’t correct), there may be a problem
with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker con-
nections. If there doesn’t seem to be a problem, you can simply use i/j to select the speaker and k/l to
change the setting and continue.
! If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the
phase (dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are
properly connected.
If Reverse Phase is displayed, the speaker’s wiring (+ and –) may be inverted. Check the speaker
connections.
If the connections were wrong, turn off the power, disconnect the power cord, then reconnect properly.
After this, perform the Auto MCACC procedure again.
If the connections were right, select GO NEXT and continue.
8 Make sure ‘OK’ is selected, then press ENTER.
A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum
receiver settings.
Again, try to be as quiet as possible while this is happening. It may take 3 to 7 minutes.
! If you selected a STAND.WAVE Multi-Point setup (in step 2), you will be asked to place the mic at the 2nd
and 3rd reference points before finally placing it at your main listening position.
9 The Auto MCACC Setup procedure is completed and the MCACC PRO menu reappears
automatically.
The settings made in the Auto MCACC Setup should give you excellent surround sound from your system, but
it is also possible to adjust these settings manually using the Manual MCACC setup menu (starting below) or
Manual SP Setup menu (starting on page 94 ).
! Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12
cm (5 inches) will end up with different size settings. You can correct the setting manually using the Manual
speaker setup on page 94 .
! The subwoofer distance setting may be farther than the actual distance from the listening position. This set-
ting should be accurate (taking delay and room characteristics into account) and generally does not need to
be changed.
! If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing
environment, we recommend adjusting the settings manually.
You can also choose to view the settings by selecting individual parameters from the MCACC Data Check screen
(see Checking MCACC Data on page 91 ).
Press RETURN after you have finished checking each screen. When you’re finished, select RETURN to go back to
the HOME MENU.
Be sure to disconnect the microphone from this receiver upon completion of the Auto MCACC Setup.

Manual MCACC setup

You can use the settings in the Manual MCACC setup menu to make detailed adjustments when you’re more
familiar with the system. Before making these settings, you should have already completed Automatically con-
ducting optimum sound tuning (Full Auto MCACC) on page 47 .
You only need to make these settings once (unless you change the placement of your current speaker system or
add new speakers).
CAUTION
! The test tones used in the Manual MCACC setup are output at high volume.
Important
! Press the MCACC button while the pertinent setup screens are displayed to select MCACC presets.
! For some of the settings below, you’ll have to connect the setup microphone to the front panel and place it
about ear level at your normal listening position. Press HOME MENU to display the HOME MENU before you
connect the microphone to this receiver.
! See Problems when using the Auto MCACC Setup on page 48 for notes regarding high background noise
levels and other possible interference.
! If you’re using a subwoofer, switch it on and turn up the volume to the middle position.
 

View the manual for the Pioneer Elite SC-91 here, for free. This manual comes under the category receivers and has been rated by 1 people with an average of a 9.9. This manual is available in the following languages: English. Do you have a question about the Pioneer Elite SC-91 or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Pioneer Elite SC-91 is a receiver that offers a range of features to enhance your home entertainment experience. With its sleek design and advanced technology, this receiver is a suitable addition to any home theater setup. One notable feature of the Pioneer Elite SC-91 is its support for 4K Ultra HD video. This means that you can enjoy high-resolution visuals with stunning clarity and detail. Additionally, it supports HDR (High Dynamic Range) content, allowing for a wider range of colors and contrast. This receiver also offers a variety of audio options. It features Dolby Atmos and DTS:X technologies, which provide immersive and three-dimensional sound. With 7.2 channels of amplification, the SC-91 can deliver powerful and clear audio. The Pioneer Elite SC-91 also includes built-in Wi-Fi and Bluetooth connectivity. This allows for easy streaming of music from your favorite devices. With support for popular streaming services such as Spotify and Pandora, you can enjoy a wide range of music options. Furthermore, this receiver features multiple HDMI inputs and outputs, making it compatible with a variety of devices such as gaming consoles and Blu-ray players. It also has USB and Ethernet ports for added connectivity options. In terms of control, the Pioneer Elite SC-91 offers a user-friendly interface and comes with a remote control. It is also compatible with smartphone apps, allowing you to control the receiver from your mobile device. Overall, the Pioneer Elite SC-91 is a versatile and feature-rich receiver that delivers high-quality audio and video performance.

General
BrandPioneer
ModelElite SC-91
Productreceiver
EAN0884938290739
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer Elite SC-91 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

How do I connect my Pioneer Elite SC-91 receiver to my TV?

Ensure that you connect the HDMI cable from the HDMI OUT port on the receiver to the HDMI IN port on your TV. Use the appropriate HDMI input on your TV to enjoy high-quality audio and video.

How do I set up a surround sound system using my Pioneer Elite SC-91 receiver?

Connect the necessary speakers to the receiver using the speaker terminals labeled for each channel, ensuring the positive and negative wires match correctly. Go to the receiver's setup menu, select speaker configuration, and follow the prompts to optimize the sound for your specific speaker setup.

I'm having trouble calibrating the audio settings on my receiver. How can I adjust the equalizer?

Navigate to the receiver's setup menu and select the "Audio" or "Sound" settings. Look for the "Equalizer" option and access it to fine-tune the audio frequencies according to your preferences. Remember to listen to various content types while adjusting to ensure a balanced sound across different genres.

How can I enable zone 2 or zone 3 functionality on my Pioneer Elite SC-91 receiver?

To enable zone 2 or zone 3 playback, go to the receiver's setup menu and locate the "Multi-Zone" or "Zone 2/3" settings. Enable the desired zone by selecting it and follow the instructions to set up the audio sources and speaker outputs for each specific zone.

My receiver is not producing any sound. What could be the issue?

Check the following: 1) Ensure the speaker wires are securely connected to the correct terminals on the receiver and speakers. 2) Make sure the volume is turned up to an audible level. 3) Verify that the source you are using is producing audio. 4) Check if the speakers are set to the appropriate channels and not muted. If the issue persists, a factory reset or a professional inspection might be necessary.

Is the manual of the Pioneer Elite SC-91 available in English?

Yes, the manual of the Pioneer Elite SC-91 is available in English .

Is your question not listed? Ask your question here

No results