Pioneer DEH-S7200BHS manual

Pioneer DEH-S7200BHS
9.1 · 1
PDF manual
 · 159 pages
English
manualPioneer DEH-S7200BHS

English

This guide is intended to guide you through the basic functions of this unit.
For details, please refer to the Operation manual stored on the website.
https://www.pioneerelectronics.com/PUSA/Support

Before You Start

Thank you for purchasing this PIONEER product
To ensure proper use, please read through this guide before using this product. It is especially
important that you read and observe WARNINGS and CAUTIONS in this guide. Please keep
the guide in a safe and accessible place for future reference.
FCC ID: EW4C95
MODEL NO.: DEH-S7200BHS
IC: 4250A-C95
This device contains licence-exempt transmitter(s)/receiver(s) that complies with Part 15
of FCC Rules and Innovation, Science, and Economic Development Canada licence-exempt
RSS(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of this device.
This transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter.
The Bluetooth antenna cannot be removed (or replaced) by user.
This equipment complies with FCC/ISED radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines
and RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment has very
low levels of RF energy that it deemed to comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should be installed and operated keeping the
radiator at least 20 cm or more away from persons body (excluding extremities: hands,
wrists, feet and ankles).
Alteration or modifications carried out without appropriate authorization may invalidate
the user’s right to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FEDERAL COMMUNICATIONS COMMISSION SUPPLIER’S DECLARATION OF CONFORMITY
Product Name: CD RDS RECEIVER
Model Number: DEH-S7200BHS
Responsible Party Name: PIONEER ELECTRONICS (USA), INC. SERVICE SUPPORT DIVISION
Address: 2050 W. 190TH STREET, SUITE 100 TORRANCE, CA 90504, U.S.A.
Phone: 1-310-952-2915
URL: http://www.pioneerelectronics.com
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a safe level—a level that lets the sound
come through clearly without annoying blaring or distortion and, most importantly, without
affecting your sensitive hearing. Sound can be deceiving.
Over time, your hearing comfort level” adapts to higher volumes of sound, so what sounds
“normal” can actually be loud and harmful to your hearing. Guard against this by setting your
equipment at a safe level BEFORE your hearing adapts.
ESTABLISH A SAFE LEVEL:
Set your volume control at a low setting.
Slowly increase the sound until you can hear it comfortably and clearly, without distortion.
Once you have established a comfortable sound level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
Do not turn up the volume so high that you can’t hear whats around you.
Use caution or temporarily discontinue use in potentially hazardous situations.
Do not use headphones while operating a motorized vehicle; the use of headphones may
create a traffic hazard and is illegal in many areas.
WARNING
Rear visibility systems (backup cameras) are required in certain new vehicles sold in the
U.S. and Canada. U.S. regulations began according to a two year phase-in on May 1, 2016,
and both the U.S. and Canada require that all such vehicles manufactured on or after May
1, 2018 have rear visibility systems. Owners of vehicles equipped with compliant rear
visibility systems should not install or use this product in a way that alters or disables
that system. If you are unsure whether your vehicle has a rear visibility system subject to
the U.S. or Canadian regulations, please contact the vehicle manufacturer or dealer.
Do not attempt to install or service this product by yourself. Installation or servicing of
this product by persons without training and experience in electronic equipment and
automotive accessories may be dangerous and could expose you to the risk of electric
shock, injury or other hazards.
Do not attempt to operate the unit while driving. Make sure to pull off the road and park
your vehicle in a safe location before attempting to use the controls on the device.
This product contains chemicals known to the State of California and other governmental
entities to cause cancer and birth defects or other reproductive harm. Wash hands after
handling.
CAUTION
Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock
could result. Also, damage to this unit, smoke, and overheating could result from contact
with liquids.
Always keep the volume low enough to hear outside sounds.
This product is evaluated in moderate and tropical climate condition under the Audio, video
and similar electronic apparatus - Safety requirements, IEC 60065.
CAUTION
This product is a Class 1 laser product classified under the safety standard, IEC 60825-
1:2014.
CAUTION:
USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION:
THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE
HAZARD.
After-sales service for Pioneer products
Please contact the dealer, distributor from where you purchased this unit or the authorized
PIONEER Service Station for after-sales service or any other information. In case the necessary
information is not available, please contact the companies listed below:
Please do not ship your unit to the companies at the addresses listed below for repair without
contacting them in advance.
U.S.A. and CANADA
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
For warranty information please see the Limited Warranty sheet included with this unit.

Connections

In the following, “NW represents network
mode and “STD” represents standard mode.
According to the connections you have
established, change the speaker mode to
standard mode (STD) or network mode
(NW).
WARNING
When speaker output is used by 4
channels, use speakers rated over 50 W
(maximum input power) and between 4 Ω
to 8 Ω (impedance value). Do not use 1 Ω
to 3 Ω speakers for this unit.
When rear speaker output is used by a 2
Ω subwoofer, use speakers rated for over
70 W.
* Please refer to connections for a
connection method.
The black cable is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wire first.
Ensure that the ground wire is properly
connected to metal parts of the cars body.
The ground wire of the power amp and the
one of this unit or any other device must
be connected to the car separately with
different screws. If the screw for the ground
wire loosens or falls out, it could result in
fire, generation of smoke or malfunction.
Metal parts
of car’s body
Two devices connected to the
car separately (ground wires)
*1 Not supplied for this unit
Important
When installing this unit in a vehicle
without an ACC (accessory) position on
the ignition switch, failure to connect
the red cable to the terminal that detects
operation of the ignition key may result in
battery drain.
ACC position No ACC position
Use this unit with a 12-volt battery and
negative grounding only. Failure to do so
may result in a fire or malfunction.
To prevent a short-circuit, overheating
or malfunction, be sure to follow the
directions below.
−Disconnect the negative terminal of the
battery before installation.
−Secure the wiring with cable clamps
or adhesive tape. Wrap adhesive tape
around wiring that comes into contact
with metal parts to protect the wiring.
−Place all cables away from moving parts,
such as the shift lever and seat rails.
−Place all cables away from hot places,
such as near the heater outlet.
−Do not connect the yellow cable to the
battery by passing it through the hole to
the engine compartment.
−Cover any disconnected cable connectors
with insulating tape.
−Do not shorten any cables.
−Never cut the insulation of the power
cable of this unit in order to share the
power with other devices. The current
capacity of the cable is limited.
−Use a fuse of the rating prescribed.
−Never wire the negative speaker cable
directly to ground.
−Never band together negative cables of
multiple speakers.
When this unit is on, control signals
are sent through the blue/white cable.
Connect this cable to the system remote
control of an external power amp or
the vehicle’s auto-antenna relay control
terminal (max. 300mA 12 V DC). If the
vehicle is equipped with a glass antenna,
connect it to the antenna booster power
supply terminal.
Never connect the blue/white cable to
the power terminal of an external power
amp. Also, never connect it to the power
terminal of the auto antenna. Doing so may
result in battery drain or a malfunction.
The graphical symbol
placed on the
product means direct current.

This unit

Microphone 3 m (9 ft. 10-1/8 in.)
SiriusXM Connect Vehicle Tuner input
Power cord input
Microphone input
Rear output (STD) or middle range output
(NW)
Front output (STD) or high range output
(NW)
Antenna input
Fuse (10 A)
Wired remote input
Hard-wired remote control adapter can be
connected (sold separately).
Subwoofer output
SiriusXM Connect Vehicle Tuner (sold
separately)
To power cord input
Front left speaker (STD) or high range left
speaker (NW)
Front right speaker (STD) or high range
right speaker (NW)
Rear left speaker (STD) or middle range
left speaker (NW)
Rear right speaker (STD) or middle range
right speaker (NW)
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Black (chassis ground)
Connect to a clean, paint-free metal
location.
Yellow
Connect to the constant 12 V supply
terminal.
Red
Connect to terminal controlled by the
ignition switch (12 V DC).
Blue/white
Connect to the system control terminal
of the power amp or auto-antenna relay
control terminal (max. 300 mA 12 V DC).
Subwoofer (4 Ω)
When using a subwoofer of 2 Ω, be sure
to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
connect anything to the green and green/
black leads.
Not used.
Subwoofer (4 Ω) × 2
Orange/white
Connect to a car’s illumination signal.

Power amp (sold

separately)

Perform these connections when using the
optional amplifier.
System remote control
Connect to blue/white cable.
Power amp (sold separately)
Connect with RCA cables (sold separately)
To rear output (STD) or middle range
output (NW)
Rear speaker (STD) or middle range
speaker (NW)
To front output (STD) or high range
output (NW)
Front speaker (STD) or high range speaker
(NW)
To subwoofer output
Subwoofer
Removing the unit (installed with the supplied mounting sleeve)1 Remove the trim ring.
Trim ring
Notched tab
Releasing the front panel allows easier
access to the trim ring.
When reattaching the trim ring, point
the side with the notched tab down.
2 Insert the supplied extraction keys into both sides of the unit until they click into place.3 Pull the unit out of the dashboard.

To secure the front panel

The front panel can be secured with the
supplied screw.
Screw

Installing the microphone

The microphone should be placed directly
in front of the driver at a suitable distance to
pick up their voice clearly.
CAUTION
It is extremely dangerous to allow the
microphone lead to become wound around
the steering column or shift lever. Be sure to
install the microphone in such a way that it
will not obstruct driving. It is recommended
to use the clamps (sold separately) to
arrange the lead.
NOTE
Depending on the vehicle model, the
microphone cable length may be too
short when you mount the microphone
on the sun visor. In such cases, install the
microphone on the steering column.

Power cord

Perform these connections when not
connecting a rear speaker or middle range
speaker lead to a subwoofer.
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Black
Yellow
Red
Blue/white
Orange/white
Perform these connections when using a
subwoofer without the optional amplifier.
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Black
Yellow
Red
Blue/white
Orange/white
Green
Green/black
Violet
Violet/black
Important
In the case of
above, two 4 Ω subwoofers
wired in parallel will represent a 2 Ω load.

Installation

Important
Check all connections and systems before
final installation.
Do not use unauthorized parts as this may
cause malfunctions.
Consult your dealer if installation requires
drilling of holes or other modifications to
the vehicle.
Do not install this unit where:
−it may interfere with operation of the
vehicle.
−it may cause injury to a passenger as a
result of a sudden stop.
Install this unit away from hot places such
as near the heater outlet.
Optimum performance is
obtained when the unit is
installed at an angle of less
than 60°.
When installing, to ensure proper heat
dispersal when using this unit, make sure
you leave ample space behind the rear
panel and wrap any loose cables so they
are not blocking the vents.
Leave ample
space
5 cm
5 cm

DIN mount installation

1 Insert the supplied mounting sleeve into the dashboard.2 Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.
Dashboard
Mounting sleeve
Make sure that the unit is installed
securely in place. An unstable
installation may cause skipping or other
malfunctions.
When not using the supplied mounting sleeve1 Determine the appropriate position where the holes on the bracket and the side of the unit match.2 Tighten the screws on each side.
Screw
Mounting bracket
Dashboard or console
Use either truss (5 mm × 9 mm) or
flush surface (5 mm × 9 mm) screws,
depending on the bracket screw holes.

To install on the sun visor

1 Fit the microphone lead into the groove.
Microphone
lead
Groove
2 Install the microphone clip on the sun visor.
Lowering the sun visor reduces the voice
recognition rate.
Microphone clip

To install on the steering

column

1 Slide the microphone base to detach it from the microphone clip.
Microphone
Microphone clip
Microphone base
2 Install the microphone on the rear side of the steering column.
Double-sided tape

CD RDS RECEIVER

AUTORADIO CD RDS

REPRODUCTOR DE CD CON RECEPTOR RDS

Important (Serial number)
The serial number is located on the bottom of this unit. For your own security and
convenience, be sure to record this number on the enclosed warranty card.
Important (Numéro de série)
Le numéro de série se trouve au bas de cet appareil. Pour votre sécurité et votre
commodité, veillez à noter ce numéro sur la carte de garantie fournie.
Importante (Número de serie)
El número de serie se encuentra en la parte inferior de esta unidad. Por su propia seguridad
y comodidad, asegúrese de anotar este número en la tarjeta de garantía que se adjunta.

Quick start guide

Guide de démarrage rapide

Guía de inicio rápido

QRD3753-A

DEH-S7200BHS

Basic operation

DEH-S7200BHS
M.C. (multi-control) dialAUX input jack (3.5 mm stereo jack)Display window
BASS
DISP (display)Disc loading slot BAND/USB port (eject)SRC (source)/OFFDetach button (navigation)/LIST
About the main menu
You can adjust various settings in the main menu.

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select one of the categories below, then press to
confirm.
• FUNCTION settings
• AUDIO settings
• SYSTEM settings
• ILLUMINATION settings
• MIXTRAX settings
3 Turn the M.C. dial to select the options, then press to confirm.
Frequently used operations
Purpose Operation
Turn on the power Press SRC/OFF to turn on the
power.
Press and hold SRC/OFF to turn
off the power.
Adjust the volume Turn the M.C. dial.
Select a source Press SRC/OFF repeatedly.
Change the display information Press DISP repeatedly.
Return to the previous display/list Press BAND/
.
Return to the normal display from
the menu
Press and hold BAND/
.
Change the display brightness
Press and hold BAND/
.
Boost the bass level Press BASS.
You can select the bass level ([HI]
or [LOW]) in [D.BASS].

Setup operation

When you turn the ignition switch to ON after installation, the setup menu appears in the
display.
Do not use the unit in standard mode when a speaker system for
network mode is connected to the unit. Do not use the unit in network
mode when a speaker system for standard mode is connected to the
unit. This may cause damage to the speakers.
WARNING
1 Turn the M.C. dial to select the options, then press to confirm.
To proceed to the next menu option, you need to confirm your selection.
Menu Item Description
LANGUAGE
[ENG](English),
[ESP](Spanish),
[FRA]
(Canadian
French)
Select the language to display the text information
from a compressed audio file.
CLOCK SET Set the clock.
1 Turn the M.C. dial to adjust the hour, then press
to confirm.
The indicator moves to the minute setting
automatically.
2 Turn the M.C. dial to adjust the minute, then press
to confirm.
SPEAKER MODE
[STANDARD],
[NETWORK]
Switch between two operation modes: the 2-way
network mode (NETWORK) and the standard mode
(STANDARD) according to the connections you have
established.
After selecting the appropriate mode, turn the M.C.
dial to select [YES], then press to confirm.
You cannot complete the setup menu without
setting the [SPEAKER MODE].

2 [QUIT :YES] appears.

To return to the first item of the setup menu, turn the M.C. dial to
select [QUIT :NO], then press to confirm.

3 Press the M.C. dial to confirm the settings.

HD Radio™ operation

Receiving preset stations
1 Press SRC/OFF to select [HD RADIO].

2 Press BAND/ to select the band.

[FM1]
[FM2] [FM3] [AM]
3 Press a number button (1/ to 6/ ).
Best stations memory (BSM)
1 After selecting the band, press the M.C. dial to display the main
menu.

2 Turn the M.C. dial to select [FUNCTION], then press to confirm.

3 Turn the M.C. dial to select [BSM], then press to confirm.

To store stations manually

1 While receiving the station you want to store, press and hold one of

the number buttons (1/
to 6/ ) until it stops flashing.

CD/USB/iPhone®/AUX operation

(iPhone source is not available when [USB MTP] is set to [ON] in the SYSTEM settings.)
CD

1 Insert a disc into the disc loading slot with the label side up.

To eject a disc, stop playback first then press
.
USB/iPhone

1 Open the USB port cover.

2 Plug in the USB device/iPhone using an appropriate cable.

A device installed with Android OS 4.0 or most of later versions can be connected to
the unit via MTP, using the cable supplied with the device. However, depending on the
connected device, OS version or the numbers of the files in the device, audio files/songs
may not be able to be played back via MTP.
NOTE
If you use an MTP connection, [USB MTP] needs to be set to [ON] in the SYSTEM settings.
AUX

1 Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select [AUX IN] as the source.
MTP connection

Bluetooth connection

Up to two Bluetooth telephones can be connected simultaneously.

1 Turn on the Bluetooth function of the device.

2 Select the unit name shown in the device display.

3 Make sure the same 6-digit number appears on this unit and the

device.

4 Select [YES].

Bluetooth telephone

Basic operations
Purpose Operation
Answer an incoming call Press any button when a call is
received.
End a call Press
.
Reject an incoming call Press and hold
when a call is
received.
Activating voice recognition mode
1 Press and hold and then talk into the microphone to input voice
commands.
To exit the voice recognition mode, press BAND/
.

Making a connection with Pioneer Smart Sync

Pioneer Smart Sync is the application that intelligently brings
your maps, messages, and music together in the vehicle.
Do not attempt to operate the application while driving. Make sure
to pull off the road and park your vehicle in a safe location before
attempting to use the controls on the application.

1 Enter the SYSTEM menu (refer to “About the main menu”).

2 Turn the M.C. dial to select [APP CONTROL], then press to confirm.

3 Turn the M.C. dial to select one of the below.

• Select [WIRED] for the USB connection.
• Select [BLUETOOTH] for the Bluetooth connection.
4 Turn the M.C. dial to select [AUTO APP CONN], then press to confirm.

5 Turn the M.C. dial to select [ON], then press to confirm.

6 Connect this unit with the mobile device via USB or Bluetooth.

Pioneer Smart Sync on the iPhone/Android device starts
automatically.
NOTE
Regardless of whether the [AUTO APP CONN] setting is set to [ON] or [OFF], you can also
perform the following to start Pioneer Smart Sync.
For devices other than the USB-connected Android device, press SRC/OFF to select any
source and press and hold the M.C. dial.
For iPhone, launch Pioneer Smart Sync on the mobile device.
WARNING

Preparing for the SiriusXM Satellite Radio service

1 Press SRC/OFF to select [SIRIUSXM].

2 Press / to select Channel 0.

The Radio ID appears on the display.In addition, the Radio ID is located on the bottom of the SiriusXM Connect Vehicle Tuner.
NOTE
The Radio ID does not include the letters I, O, S or F.

3 Activate the SiriusXM service online or by phone.

For US Subscriptions: Visit www.siriusxm.com/activatenow Call SiriusXM Listener Care at 1-866-635-2349For Canadian Subscriptions: Visit www.siriusxm.ca/activatexm Call 1-877-438-9677

4 [SUBSCRIPTION UPDATED] appears on the display when your

SiriusXM Connect Vehicle Tuner has been subscribed successfully.
Press any key to clear the activation message.

View the manual for the Pioneer DEH-S7200BHS here, for free. This manual comes under the category car radios and has been rated by 1 people with an average of a 9.1. This manual is available in the following languages: English. Do you have a question about the Pioneer DEH-S7200BHS or do you need help? Ask your question here

Need help?

Do you have a question about the Pioneer and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 4
D
Damion LasleyAugust 25, 2021

What does “error 23” mean?? I can hear what’s on the usb thumb drive! What can I do to clear this message so I can listen to what is on the USB?

What does “error 23” mean?? I can hear what’s on the usb thumb drive! What can I do to clear this message so I can listen to ...
zoom-in
View photo
K
kJune 12, 2021

how do you change the sirius station?

P
pierre lemireJanuary 31, 2024

How to transfer phone contacts to radio?

L
Lawrence deasSeptember 21, 2023

How do you change the language

The Pioneer DEH-S7200BHS is a car radio designed to enhance the audio experience while driving. It offers a range of features and functions that aim to provide convenience and high-quality sound. One notable feature of the Pioneer DEH-S7200BHS is its Bluetooth connectivity, which allows users to stream music and make hands-free calls wirelessly. This eliminates the need for tangled wires and provides a seamless connection to compatible devices. Additionally, this car radio supports a wide range of audio formats, allowing users to enjoy their music without worrying about compatibility issues. The DEH-S7200BHS also includes a built-in HD Radio tuner, providing access to enhanced, crystal-clear radio broadcasts. This feature enables users to listen to their favorite radio stations with improved sound quality. Moreover, this car radio features advanced sound customization options such as a 13-band graphic equalizer and Auto EQ, allowing users to fine-tune the audio output to their preferences. It also includes built-in amplification, providing more power to the speakers for a better listening experience. The Pioneer DEH-S7200BHS has a sleek design with an easy-to-use interface that maximizes the user experience. It also includes a remote control for added convenience and accessibility. In summary, the Pioneer DEH-S7200BHS car radio offers a range of features and functions designed to improve the in-car audio experience. Its Bluetooth connectivity, HD Radio tuner, and sound customization options make it an appealing choice for those seeking high-quality sound and convenience while driving.

General
BrandPioneer
ModelDEH-S7200BHS
Productcar radio
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF), Product Brochure (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pioneer DEH-S7200BHS below.

What is the difference between FM and AM?

FM stands for Frequency Modulation and AM stands for Amplitude Modulation. The biggest difference between FM radio stations compared to AM radio stations is the sound quality.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

My car radio does not turn on, now what?

If your car radio does not turn on, it will not receive any power. Check that the red wire is connected to the contact power supply and the yellow wire to the constant power supply.

How can I best clean my car radio?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

How can I adjust the audio settings on my Pioneer DEH-S7200BHS?

You can easily adjust the audio settings by accessing the "Audio" menu on the car radio display. From there, you can modify the equalizer settings, adjust the balance and fader, and control other audio options to enhance your listening experience.

How do I pair my smartphone via Bluetooth with the car radio?

To connect your smartphone to the Pioneer DEH-S7200BHS via Bluetooth, first enable Bluetooth on your phone. Then, go to the "Bluetooth Settings" menu on the car radio display, select "Pair Device," and follow the on-screen prompts to complete the pairing process.

Can I customize the display color of the car radio?

Yes, you can personalize the display color on your Pioneer DEH-S7200BHS. Simply access the "Display" menu, choose "Color Customization," and select your preferred color combination for the display illumination.

How can I set up my favorite radio stations for quick access?

Setting up your favorite radio stations is easy on the Pioneer DEH-S7200BHS. Tune in to the desired radio station, then press and hold one of the numbered preset buttons on the car radio until a beep is heard. This will assign the current station to that particular preset button for instant access in the future.

Is it possible to connect external audio devices to the car radio?

Absolutely! The Pioneer DEH-S7200BHS provides various connectivity options. You can connect external audio devices such as an MP3 player or smartphone using the auxiliary input or USB port located on the front panel. Additionally, this car radio supports Bluetooth audio streaming for wireless playback from compatible devices.

Is the manual of the Pioneer DEH-S7200BHS available in English?

Yes, the manual of the Pioneer DEH-S7200BHS is available in English .

Is your question not listed? Ask your question here

No results