Philips HD1134 manual

Philips HD1134
8.4 · 1
PDF manual
 · 5 pages
manualPhilips HD1134


Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips offers,
register your product at
Read this user manual carefully before you use the
appliance and save it for future reference.
Never immerse the iron in water.
Check if the voltage indicated on the type plate
corresponds to the local mains voltage before you
connect the appliance.
Do not use the appliance if the plug, the mains cord
or the appliance itself shows visible damage, or if the
appliance has been dropped.
If the mains cord is damaged, you must have it
replaced by Philips, a service centre authorised by
Philips or similarly qualied persons in order to avoid
a hazard.
Never leave the appliance unattended when it is
connected to the mains.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Do not let the mains cord come into contact with
the hot soleplate of the iron.
Only connect the appliance to an earthed wall
Check the mains cord regularly for possible damage.
Always place and use the iron on a stable, level and
horizontal surface.
The soleplate of the iron can become extremely hot
and may cause burns if touched.
When you have nished ironing, when you clean the
appliance and also when you leave the iron even for
a short while: put the iron on its heel and remove
the mains plug from the wall socket.
The appliance is intended for household use only.
Electromagnetic elds (EMF)
This Philips appliance complies with all standards
regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this user
manual, the appliance is safe to use based on scientic
evidence available today.
General description (Fig. 1)
A Temperature dial

B Temperature light

C Mains cord

D Heel

E Type plate

F Soleplate

Before first use

1 Remove any sticker or protective foil from the


2 Let the iron heat up to maximum temperature and

pass the iron over a piece of damp cloth for several
minutes to remove any residues from the soleplate.
Using the appliance
Setting the temperature
1 Put the iron on its heel.
2 To set the required ironing temperature, turn the
temperature dial to the appropriate position (Fig. 2).
Check the laundry care label for the required ironing
1 Synthetic fabrics (e.g. acrylic, viscose, polyamide,
1 Silk
2 Wool
3 Cotton, linen
If you do not know what kind or kinds of fabric an article
is made of, determine the right ironing temperature by
ironing a part that is not visible when you wear or use
the article.
Silk, woollen and synthetic materials: iron the reverse side
of the fabric to prevent shiny patches.
Start ironing the articles that require the lowest ironing
temperature, such as those made of synthetic bres.

3 Put the mains plug in an earthed wall socket.

Note: The iron may give off some smoke when you use it for
the rst time. This stops after a short while.

1 Put the iron on its heel.

2 Put the mains plug in an earthed wall socket.

3 Set the recommended ironing temperature (see

section ‘Setting the temperature’ above) (Fig. 2).

4 Lettheironheatupuntilthetemperaturelightrst

goes out and then goes on again (Fig. 3).
Note: The temperature light goes on from time to time
during ironing.

5 Start ironing.

Tip: Ironing is easier and takes less time if you moisten the
article rst.

1 Put the iron on its heel.

2 Remove the mains plug from the wall socket and let

the iron cool down for at least 30 minutes.

3 Wipe the soleplate with a damp cloth and a non-

abrasive (liquid) cleaning agent.
To keep the soleplate smooth, avoid hard contact with
metal objects. Never use a scouring pad, vinegar or
other chemicals to clean the soleplate.

4 Clean the upper part of the iron with a damp cloth.


1 Put the iron on its heel.

2 Remove the mains plug from the wall socket and let

the iron cool down for at least 30 minutes.

3 Wind the mains cord round the cord storage

facility (Fig. 4).

4 Store the iron on its heel in a safe and dry

place (Fig. 5).
Do not throw away the appliance away with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve the
environment (Fig. 6).
Guarantee & service
If you need service or information or if you have a
problem, please visit the Philips website at
com or contact the Philips Consumer Care Centre
in your country (you nd its phone number in the
worldwide guarantee leaet). If there is no Consumer
Care Centre in your country, go to your local Philips
This chapter summarises the most common problems
you could encounter with the appliance. If you are unable
to solve the problem with the information below, contact
the Consumer Care Centre in your country.
Problem Possible cause Solution
The iron is plugged
in but the soleplate
is cold.
There is a connection problem. Check the mains cord, the plug and the wall socket.
The temperature dial is set to
Set the temperature dial to the required position (see
section ‘Setting the temperature’ in chapter ‘Using the

View the manual for the Philips HD1134 here, for free. This manual comes under the category Irons and has been rated by 1 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Philips HD1134 or do you need help? Ask your question here

Need help?

Do you have a question about the Philips and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Philips owners to provide you with a good answer.

Number of questions: 0

HD1134 | HD1134/28
User manual (PDF)
AC input voltage240 V
Power750 W
TypeDry iron
Variable steam-
Cord length- m
Steam boost performance- g/min
Product colourBlack
Automatic anti-calc-
Vertical steam function-
Steam boost function-
Iron weight800 g
Non-twisting cord-
Weight & dimensions
Width237 mm
Depth118 mm
Height105 mm
Weight800 g
Other features
Dimensions (W x D x H)23.7 x 10.5 x 11.8 cm
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Philips HD1134 below.

Is your question not listed? Ask your question here

No results