View the manual for the Philips DES7500DCH here, for free. This manual comes under the category door bells and has been rated by 2 people with an average of a 9.3. This manual is available in the following languages: English. Do you have a question about the Philips DES7500DCH or do you need help? Ask your question here

Below you will find the product specifications and the manual specifications of the Philips DES7500DCH.
| Brand | Philips |
| Model | DES7500DCH | DES7500DCH/10 |
| Product | door bell |
| EAN | 3345115310130 |
| Language | English |
| Filetype | User manual (PDF) |
| 2 | |
| 2 |
| Product color | Grey, White |
| International Protection (IP) code | IP65 |
| Built-in camera | No |
| Connectivity technology | Wireless |
| Frequency | 433 MHz |
| Maximum range | 300 m |
| Power source type | AC, Battery |
| Input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Battery voltage | 24 V |
| Transmitter width | 150 mm |
| Transmitter depth | 66 mm |
| Transmitter height | 210 mm |
| Operating temperature (T-T) | -10 - 55 °C |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Philips DES7500DCH below.
No, the Philips DES7500DCH does not have a built-in camera.
The Philips DES7500DCH has wireless connectivity technology.
The Philips DES7500DCH can be powered by both AC and battery.
The battery voltage of the Philips DES7500DCH is 24 V.
The Philips DES7500DCH has a maximum range of 300 m.
To pair the Philips DES7500DCH door bell with the receiver, follow these steps: 1. Make sure the receiver is plugged into a power outlet and turned on. 2. Press and hold the pairing button on the receiver until the LED indicator starts flashing. 3. On the door bell, locate the pairing button. It is usually located on the back or side of the device. 4. Press and hold the pairing button on the door bell until the LED indicator starts flashing. 5. Release the pairing button on both the receiver and the door bell. 6. Wait for the LED indicators on both devices to stop flashing and remain solid. 7. The door bell is now paired with the receiver. Test the connection by pressing the door bell button and checking if the receiver chimes. Note: If the pairing process fails, try resetting both the receiver and the door bell by removing the batteries or power source, waiting for a few seconds, and then repeating the pairing process. Please refer to the manual for more detailed instructions and troubleshooting tips.
There could be several reasons why the Philips DES7500DCH door bell is not working after installation. Here are some possible troubleshooting steps: 1. Check the power source: Ensure that the receiver is properly plugged into a power outlet and turned on. Also, make sure that the batteries in the door bell are correctly installed and not depleted. 2. Verify the pairing: Confirm that the door bell is properly paired with the receiver. Follow the pairing instructions in the manual to ensure a successful connection. 3. Check the signal range: Make sure that the door bell and receiver are within the specified signal range. If they are too far apart, the connection may be weak or non-existent. 4. Remove any interference: Keep the door bell away from other electronic devices that may cause interference, such as Wi-Fi routers or cordless phones. These devices can disrupt the signal and affect the door bell's performance. 5. Reset and reconfigure: If all else fails, try resetting both the door bell and the receiver. Remove the batteries or power source, wait for a few seconds, and then reconfigure the pairing process. Remember, if the issue persists, it is recommended to consult the manual or contact Philips customer support for further assistance.
To adjust the volume of the Philips DES7500DCH door bell, follow these steps: 1. Locate the volume control button on the door bell. It is usually located on the side or bottom of the device. 2. Press the volume control button to increase or decrease the volume. Each press will adjust the volume level incrementally. 3. Continue pressing the volume control button until you reach the desired volume level. 4. Test the volume by pressing the door bell button and listening to the chime. Adjust the volume further if needed. 5. If the volume control button does not change the volume, check the batteries in the door bell. Low battery power can affect the volume level. 6. If the issue persists, refer to the troubleshooting section in the manual for further assistance. Please note that the exact location and operation of the volume control button may vary slightly depending on the specific model of the Philips DES7500DCH door bell.
There could be several reasons why the Philips DES7500DCH door bell is not ringing when someone presses the button. Here are some possible troubleshooting steps: 1. Check the power source: Ensure that the receiver is properly plugged into a power outlet and turned on. Also, make sure that the batteries in the door bell are correctly installed and not depleted. 2. Verify the pairing: Confirm that the door bell is properly paired with the receiver. Follow the pairing instructions in the manual to ensure a successful connection. 3. Check the signal range: Make sure that the door bell and receiver are within the specified signal range. If they are too far apart, the connection may be weak or non-existent. 4. Inspect the door bell button: Check if the door bell button is functioning properly. Ensure that it is not stuck or damaged. Clean the button and surrounding area to remove any dirt or debris that may be affecting its operation. 5. Test the chime settings: Check the chime settings on the receiver. Make sure that the desired chime sound is selected and the volume is set appropriately. 6. Reset and reconfigure: If all else fails, try resetting both the door bell and the receiver. Remove the batteries or power source, wait for a few seconds, and then reconfigure the pairing process. If the issue persists, it is recommended to consult the manual or contact Philips customer support for further assistance.
To change the batteries in the Philips DES7500DCH door bell, follow these steps: 1. Locate the battery compartment on the back or bottom of the door bell. 2. Open the battery compartment by sliding or lifting the cover. 3. Remove the old batteries from the compartment, taking note of their orientation. 4. Insert new batteries of the same type or equivalent into the compartment, ensuring they are inserted correctly according to the polarity markings. 5. Close the battery compartment by sliding or securing the cover back into place. 6. Test the door bell by pressing the button to check if it rings. Note: It is recommended to use fresh batteries and replace all batteries at the same time for optimal performance. Refer to the battery type and replacement instructions in the manual for specific guidance. Please refer to the manual for more detailed instructions and illustrations if needed.
Yes, the manual of the Philips DES7500DCH is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Philips and is the answer not in the manual?
Question and answer
Number of questions: 0