Panasonic SC-BTT350 manual

Panasonic SC-BTT350
6.5 · 1
PDF manual
 · 52 pages
English
manualPanasonic SC-BTT350
42
VQT2W18
Reference

Troubleshooting guide

Before requesting service, please perform the following steps.
The following do not indicate a problem with this unit:
Regular disc rotating sounds.
Image disturbance during search.
Image disturbance when replacing 3D discs.
Unit does not respond to the remote control
or front panel buttons.
Press and hold [POWER Í/I] on the main unit for 5 seconds.
jIf still unable to power the unit off, disconnect the power cord,
wait 1 minute, then reconnect the power cord.
Cannot eject disc.
The unit may have a problem.
While the unit is off, press and hold [SKIP9] on the remote
control and [< OPEN/CLOSE] on the unit at the same time for
more than 5 seconds.
To return to the factory preset
Select “Yes” in “Restore Default Settings” in the Setup menu.
(> 39)
To return all settings to the factory preset
Reset the unit as follows:
While the unit is off, press and hold [+ VOLUME], [< OPEN/
CLOSE] and [POWER Í/I] on the main unit at the same
time for more than 5 seconds.
The remote control doesn’t work properly.
The remote control and main unit are using different codes.
Change the code on the remote control. (> 21)
It may be necessary to set the code of the remote control
again after changing the batteries for the remote control.
(> 21)
Disc cannot be played.
The disc is dirty. (> 9)
Check the region code.
Still pictures (JPEG) do not playback normally.
The images that were edited on the PC, such as Progressive
JPEG, etc., may not playback.
The TV tuner mode is not displayed when the TV is
switched on.
This phenomenon may occur, depending on the TV setting,
when “Quick Start” is set to “On”.
Depending on the TV, this phenomenon may be prevented
by reconnecting the HDMI cable to a different HDMI input
terminal or by changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
While the disc tray is empty and “BD/DVD” is selected as a
source, press and hold [SKIP:] on the remote control and
[1] (Play) on the unit at the same time for more than 5
seconds. The ratings level returns to the factory preset.
No power.
Insert the AC power supply cord securely into a household
AC outlet. (> 18)
The unit switches to standby mode.
This unit will automatically turn to standby mode after 30
minutes if it is inactive. (> 7)
When the time set for the sleep timer has passed, the power
will be turned off. (> 6)
One of the unit’s safety devices is activated. Press
[POWER Í/I] on the main unit to turn the unit on.
Power of this unit is turned off when the input for the TV is
changed.
This is a normal phenomenon when using VIERA Link
(HDAVI Control 4 or later). For details please read the
operating instructions for the TV.
The display is dim.
Change “FL Display” in the Setup menu. (> 37)
The images from this unit do not appear on the TV.
Picture is distorted.
Jittering occurs.
An incorrect resolution is selected in “HDMI Resolution”.
Reset the setting as follows:
While the disc tray is empty and “BD/DVD” is selected as a
source, press and hold [1] (Play) and [] (Stop) on the main
unit at the same time for more than 5 seconds to cancel the
setting.
When Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio
are not output in bitstream, select “Yes” in “Restore Default
Settings” and make proper settings. (> 39)
When “Playback Method for 3D Disc” in the Setup menu is
set to “3D Playback”, images may not output depending on
the connection method. Remove the disc from this unit and
select “2D Playback”.(> 36)
Video is not output.
Set the “High Clarity Sound” in the Playback menu to “Off” to
use the VIDEO OUT terminal. (> 35)
Video is not output in high-definition.
Confirm that “HDMI Resolution” in the Setup menu is set
properly. (> 38)
Do you have the latest firmware installed?
Firmware updates may be released to correct operating
irregularities that are discovered with certain movies.
(> 20)
4
Make the following checks and visit our
website for more information.
http://www2.panasonic.com/consumer-electronics/support/
Enter the model number.
4
Even so, you still have trouble,
Visit our website to find a service center.
You can find a service center near you easily on our
website.
Other support information:
“Customer Services Directory (United States and Puerto
Rico)” (> 51)

General operation

Power

Displays

TV screen and video

SC-BTT750_350P_VQT2W18_eng.book 42 ページ 2010年6月21日 月曜日 午後4時51分

Manual

View the manual for the Panasonic SC-BTT350 here, for free. This manual comes under the category blu-ray players and has been rated by 1 people with an average of a 6.5. This manual is available in the following languages: English. Do you have a question about the Panasonic SC-BTT350 or do you need help? Ask your question here

Need help?

Do you have a question about the Panasonic and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Panasonic SC-BTT350 specifications

Below you will find the product specifications and the manual specifications of the Panasonic SC-BTT350.

General
BrandPanasonic
ModelSC-BTT350 | SC-BTT350
Productblu-ray player
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Panasonic SC-BTT350 below.

How do I connect the Panasonic SC-BTT350 blu-ray player to my TV?

To connect the Panasonic SC-BTT350 blu-ray player to your TV, follow these steps: 1. Turn on your TV and select the appropriate video input. Use the TV remote to navigate to the input where you want to connect the blu-ray player. 2. Press the power button ([Í]) on the Panasonic SC-BTT350 blu-ray player to turn it on. 3. Insert the media (such as a Blu-ray disc, DVD, CD, or SD card) that you want to play into the blu-ray player. 4. The playback will start automatically. If a menu is displayed, use the arrow buttons ([3], [4], [2], [1]) on the blu-ray player remote to select the desired item and press [OK] to confirm. 5. To navigate through menus, you can use the [TOP MENU/DIRECT NAVIGATOR] or [POP-UP MENU] button on the remote. Use the arrow buttons to select the item and press [OK] to confirm. 6. If you want to show the status messages while playing, press the [STATUS] button on the remote. Each press of the [STATUS] button will display different information about the playback. 7. To stop playback and preserve the blu-ray player's motor and your TV screen, press the [∫STOP] button when you finish watching. Remember, these steps are a general guide and may vary slightly depending on your specific TV model and setup.

Why is the Panasonic SC-BTT350 blu-ray player not playing the disc?

There could be several reasons why the Panasonic SC-BTT350 blu-ray player is not playing the disc. Here are some troubleshooting steps you can try: 1. Check the disc: Ensure that the disc is clean and free from scratches or smudges. If the disc is damaged, try playing a different disc to see if the issue persists. 2. Region compatibility: Verify that the disc you are trying to play is compatible with the region code of the blu-ray player. The Panasonic SC-BTT350 supports BD-Video discs marked with the region code A. 3. Firmware update: Make sure that you have the latest firmware installed on the blu-ray player. Firmware updates may address operating irregularities and improve compatibility with certain discs. Refer to the user manual or manufacturer's website for instructions on how to update the firmware. 4. Power cycle: Turn off the blu-ray player and unplug it from the power source for a few minutes. Then, plug it back in and turn it on again. This can help reset the player and resolve temporary issues. 5. Factory reset: If the above steps do not resolve the issue, you can try performing a factory reset on the blu-ray player. Refer to the user manual for instructions on how to restore the default settings. If the problem persists after trying these troubleshooting steps, it may be necessary to contact customer support for further assistance.

How do I resume playback from where I left off on the Panasonic SC-BTT350 blu-ray player?

To resume playback from where you left off on the Panasonic SC-BTT350 blu-ray player, follow these steps: 1. Press the [∫STOP] button on the blu-ray player remote to stop playback. The stopped position will be memorized. 2. When you want to resume playback, press the [1PLAY] button on the remote. The blu-ray player will restart from the position where you stopped. Please note that the resume play function may not work on BD-Video discs that include BD-J (interactive features). Additionally, if you open the tray or press the [∫STOP] button multiple times to display "STOP" on the unit's display, the position will be cleared. By following these steps, you can easily resume playback from where you left off on the Panasonic SC-BTT350 blu-ray player.

How do I search for a specific scene in a video on the Panasonic SC-BTT350 blu-ray player?

To search for a specific scene in a video on the Panasonic SC-BTT350 blu-ray player, follow these steps: 1. While playing the video, press the [SEARCH 6] or [SEARCH 5] button on the blu-ray player remote. This will activate the search function. 2. Use the [SEARCH 6] button to fast forward the video and the [SEARCH 5] button to rewind the video. Each press of the button will increase the speed of the search. 3. To slow down the search speed, press the [SEARCH 6] or [SEARCH 5] button again. Pressing the [1PLAY] button will revert to normal playback speed. 4. If you want to skip to a specific title, chapter, or track, press the [SKIP :] or [SKIP 9] button while the video is paused. Each press of the button will increase the number of skips. 5. To perform frame-by-frame search, press and hold the [2] (2;) or [1] (;1) button while the video is paused. This will allow you to move forward or backward frame by frame. By following these steps, you can easily search for a specific scene in a video on the Panasonic SC-BTT350 blu-ray player.

How do I change the audio language on the Panasonic SC-BTT350 blu-ray player?

To change the audio language on the Panasonic SC-BTT350 blu-ray player, follow these steps: 1. While playing a video, press the [DISPLAY] button on the blu-ray player remote. This will bring up the playback menu. 2. Use the arrow buttons ([3], [4], [2], [1]) on the remote to navigate through the menu options. Look for the "Soundtrack" or "Audio" option and press [OK] to select it. 3. Use the arrow buttons to select the desired audio language from the available options. Press [OK] to confirm your selection. 4. If the video has multiple audio tracks, you can switch between them by repeating step 3 and selecting a different language. 5. To exit the menu and resume playback, press the [DISPLAY] button again. By following these steps, you can easily change the audio language on the Panasonic SC-BTT350 blu-ray player. Please note that the availability of different audio languages may vary depending on the disc being played.

Is the manual of the Panasonic SC-BTT350 available in English?

Yes, the manual of the Panasonic SC-BTT350 is available in English .

Is your question not listed? Ask your question here

No results