Chapter 3Basic Operations — Switching on/off the projector
56 - ENGLISH
Note
fWhile the power indicator <ON (G)/STANDBY (R)> lights in orange, the fan is running to cool the projector.
fFor approximately 15 seconds after the projector is switched off, the indicator does not light up even if the power is switched on. Turn on the
power again after the power indicator <ON (G)/STANDBY (R)> lights in red.
fThe projector consumes power even in standby mode (power indicator <ON (G)/STANDBY (R)> lit in red). Refer to “Power consumption”
(x page 216) for the power consumption.
fWhen the projector receives the signal from the remote control, the power indicator <ON (G)/STANDBY (R)> will blink in the following color
according to the status of the projector.
gWhen the projector is in projection mode: Green
gWhen the projector is in standby mode: Orange
However, if the [PROJECTOR SETUP] menu → [STANDBY MODE] is set to [ECO], the indicator will stay lit in red and will not blink if the
projector is in standby mode.
fThe power indicator <ON (G)/STANDBY (R)> will blink slowly in green while the shutter function is in use (shutter: closed), or while the
function of the [PROJECTOR SETUP] menu → [NO SIGNAL LIGHTS-OUT] (x page 136) is operating and the light source is turned off.
fIf the power indicator <ON (G)/STANDBY (R)> is blinking in red, consult your dealer.
Switching on the projector
Install the projection lens before switching on the projector.
Remove the lens cover rst.
2)
4)
4)
3)
1)
1) Connect the power cord to the projector.
2) Connect the power plug to an outlet.
3) Press the <ON> side of the <MAIN POWER> switch to turn on the power.
fThe power indicator <ON (G)/STANDBY (R)> lights in red, and the projector enters the standby mode.
4) Press the power on <b> button.
fThe power indicator <ON (G)/STANDBY (R)> lights in green and the image is soon projected on the screen.
Attention
fAlways remove the lens cover before starting the projection. Projecting continuously while the lens cover is attached may cause the lens
cover to heat up and result in a re.
Note
fA warm-up period of up to approximately ve minutes may be necessary until an image is displayed when the projector is switched on at
around 0 °C (32 °F).
The temperature indicator <TEMP> lights during the warm-up period. When the warm-up is completed, the temperature indicator <TEMP>
turns off and the projection starts. Refer to “When an indicator lights up” (x page 186) for the indicator status display.
fIf the operating environment temperature is low and warm-up takes more than ve minutes, the projector will judge that a problem has
occurred and the power will automatically be set to standby mode. In such case, increase the operating environment temperature to 0 °C
(32 °F) or higher, turn off the main power, and then turn on the power again.
fIt may take longer to start the projection after the power is turned on when the [PROJECTOR SETUP] menu → [STANDBY MODE] is set to
[ECO], compared to when it is set to [NORMAL].
fWhen the [PROJECTOR SETUP] menu → [INITIAL STARTUP] is set to [LAST MEMORY], and the power was turned off at the previous
use by pressing the <OFF> side of the <MAIN POWER> switch while projecting or with the power breaker, the power indicator <ON (G)/
STANDBY (R)> will light up in green and the image is projected after a while when the power is turned on by pressing <ON> side of the
<MAIN POWER> switch while the power plug is plugged into the outlet, or when the power breaker is turned on.
Manual
View the manual for the Panasonic PT-RZ12K here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 7.6. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-RZ12K or do you need help? Ask your question here
Do you have a question about the Panasonic and is the answer not in the manual?
Receive updates on solutions
Get answers to your question
Question and answer
Number of questions: 1
H
Hernán April 4, 2022
What is the sep chip used to connect the lamp and what is its name and where to buy?
View photoThis message has been automatically translated
Panasonic PT-RZ12K specifications
Below you will find the product specifications and the manual specifications of the Panasonic PT-RZ12K.
The Panasonic PT-RZ12K is a video projector designed to deliver high brightness and exceptional image quality. With a brightness of 12000 ANSI lumens, this projector is suitable for large venues such as auditoriums, conference halls, and theaters, ensuring clear and vivid visuals even in well-lit environments.
Featuring a native resolution of WUXGA (1920x1200), the PT-RZ12K delivers sharp and detailed images, making it ideal for presentations, movies, and gaming. The projector's 16:10 native aspect ratio and supported aspect ratios ensure compatibility with a wide range of content formats for versatile usage.
Equipped with a contrast ratio of 20000:1, the PT-RZ12K produces deep blacks and vibrant colors, enhancing image depth and overall visual quality. Its dot clock scanning frequency of 162 MHz ensures smooth and flicker-free image reproduction.
The projector comes with an air filter that helps maintain the optimal cooling performance, ensuring reliable and efficient operation. Additionally, its heat dissipation rate of 4096 BTU/h ensures effective cooling and prevents overheating, even during prolonged use.
The PT-RZ12K offers high uniformity of 90%, ensuring consistent brightness distribution across the projection area. This feature is essential for achieving a well-balanced and immersive viewing experience.
The projector includes a resource CD for easy installation and setup, providing users with the necessary software and documentation. With its premium build quality and attention to detail, the PT-RZ12K guarantees long-lasting performance and durability.
In summary, the Panasonic PT-RZ12K video projector combines impressive brightness, excellent image resolution, and convenient features to deliver exceptional visual experiences in various professional settings.
Need help?
Do you have a question about the Panasonic and is the answer not in the manual?
Question and answer
Number of questions: 1What is the sep chip used to connect the lamp and what is its name and where to buy?