Panasonic PT-MZ770EJ manual

Panasonic PT-MZ770EJ
8.9 · 1
PDF manual
 · 233 pages
English
manualPanasonic PT-MZ770EJ

Chapter 4Settings — [NETWORK/USB] menu

146 - ENGLISH

[SUBNET MASK]
255.255.255.0
[DEFAULT GATEWAY]
192.168.11.1
[DNS1]/[DNS2]
(Blank)

[PROJECTOR NAME]

Name of the projector can be changed. Enter if a host name is required when using the DHCP server, etc.

1) Press as to select [PROJECTOR NAME].

2) Press the <ENTER> button.

f The [PROJECTOR NAME CHANGE] screen is displayed.
3) Press asqw to select the character, and press the <ENTER> button to enter the character.

f Up to 16 characters can be entered.

4) Once the entry of the projector name is completed, press asqw to select [OK], and press the

<ENTER> button.

f To cancel, select [CANCEL].

Note
f The factory default of the projector name is “Namexxxx”. xxxx is the last four digits of the network ID. The network ID is a xed value
assigned to each product. The network ID can be conrmed in the standby screen projected when switched to Panasonic APPLICATION
input.

[NETWORK CONTROL]

Set up the control method of the network.

1) Press as to select [NETWORK CONTROL].

2) Press the <ENTER> button.

f The [NETWORK CONTROL] screen is displayed.

3) Press as to select an item, and press qw to change the setting.

[WEB CONTROL]
Set to [ON] to control with the web browser.
[PJLink CONTROL]
Set to [ON] to control with the PJLink protocol.
[PJLink NOTIFICATION]
Set to [ON] to use the PJLink notication function.
f The [PJLink NOTIFICATION] screen is displayed when set to [ON] and the <ENTER> button is
pressed. Set the IP address of the computer to notify the status of the projector in [NOTIFIED IP
ADDRESS 1], [NOTIFIED IP ADDRESS 2].
[COMMAND CONTROL]
Set to [ON] to control with the control command format (x page 217) for the <SERIAL IN> terminal.
Refer to “Control commands via LAN” (x page 212).
[COMMAND PORT]
Set the port number used for command control.
[Crestron Connected(TM)]
Set to [ON] to control with Crestron Connected of Crestron Electronics, Inc.
[AMX D.D.]
Set to [ON] to control with the controller of AMX Corporation.
Setting this function to [ON] enables detection through “AMX Device Discovery”. For details, visit the
website of AMX Corporation.
URL http://www.amx.com/
[EXTRON XTP]
Set to [ON] when connecting the “XTP transmitter” of Extron Electronics to the <DIGITAL LINK/LAN>
terminal.
The [EXTRON XTP] setting must be set to [OFF] when connecting the optional DIGITAL LINK output
supported device (Model No.: ET-YFB100G, ET-YFB200G).
For details of the “XTP transmitter”, visit the website of Extron Electronics.
URL http://www.extron.com/

4) Press as to select [STORE], and press the <ENTER> button.

f The conrmation screen is displayed.

5) Press qw to select [OK], and press the <ENTER> button.

[MEMORY VIEWER]

Set the operation of the Memory Viewer.

1) Press as to select [MEMORY VIEWER].

Manual

View the manual for the Panasonic PT-MZ770EJ here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 8.9. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-MZ770EJ or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Panasonic and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Panasonic PT-MZ770EJ specifications

Below you will find the product specifications and the manual specifications of the Panasonic PT-MZ770EJ.

General
BrandPanasonic
ModelPT-MZ770EJ | PT-MZ770EJ
Productvideo projector
LanguageEnglish
FiletypeUser manual (PDF)
Projector
Projector native resolutionWUXGA (1920x1200)
Projector brightness8000 ANSI lumens
Projection technologyLCD
Contrast ratio (typical)-
Native aspect ratio16:10
Screen size compatibility40 - 400 "
Projection distance1.02 - 10.16 m
Contrast ratio (dynamic)3000000:1
Keystone correction, horizontal-35 - 35 °
Keystone correction, vertical-35 - 35 °
Multimedia
Built-in speaker(s)Yes
RMS rated power10 W
Light source
Service life of light source- h
Design
Product typeLarge venue projector
Product colorWhite
Housing materialABS, Plastic
Market positioning-
PlacementDesktop
Lens system
Focal length range26.8 - 45.5 mm
Aperture range (F-F)1.7 - 2.3
Throw ratio1.6 - 2.8:1
Display
Built-in display-
Power
Power sourceAC
Power consumption (standby)- W
AC input frequency50 - 60 Hz
AC input voltage100 - 240 V
Video
Analog signal format system-
Full HDYes
3DNo
Ports & interfaces
VGA (D-Sub) ports quantity4
HDMI ports quantity2
Composite video in0
Component video (YPbPr/YCbCr) in0
DVI portNo
USB 2.0 ports quantity1
Audio (L/R) in2
Audio (L/R) out1
S-Video inputs quantity-
BNC input ports5
DC-in jackYes
Network
Ethernet LAN (RJ-45) ports2
Smart TVNo
Ethernet LANYes
Wi-FiNo
Operational conditions
Operating temperature (T-T)0 - 45 °C
Operating relative humidity (H-H)20 - 80 %
Other features
RS-232 ports-
Weight & dimensions
Weight17100 g
Width560 mm
Depth443 mm
Height205 mm
Packaging content
Handheld remote control-
Storage
Card reader integrated-
Features
Noise level35 dB
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Panasonic PT-MZ770EJ below.

What is the weight of the Panasonic PT-MZ770EJ?

The Panasonic PT-MZ770EJ has a weight of 17100 g.

What is the height of the Panasonic PT-MZ770EJ?

The Panasonic PT-MZ770EJ has a height of 205 mm.

What is the width of the Panasonic PT-MZ770EJ?

The Panasonic PT-MZ770EJ has a width of 560 mm.

What is the depth of the Panasonic PT-MZ770EJ?

The Panasonic PT-MZ770EJ has a depth of 443 mm.

Is the manual of the Panasonic PT-MZ770EJ available in English?

Yes, the manual of the Panasonic PT-MZ770EJ is available in English .

Is your question not listed? Ask your question here

No results