fThe power management function will also operate in MEMORY VIEWER, MIRRORING, and Panasonic APPLICATION inputs. The condition
to determine that there is no input signal is as follows.
gMEMORY VIEWER input: USB memory is not attached to the <VIEWER/PAIRING> terminal
gMIRRORING input, Panasonic APPLICATION input: There is no connection from the computer, etc.
Setting [STANDBY MODE]
Set the power consumption during standby and whether to enable the [QUICK STARTUP] function.
1) Press as to select [ECO MANAGEMENT].
2) Press the <ENTER> button.
f The [ECO MANAGEMENT] screen is displayed.
3) Press as to select [STANDBY MODE].
4) Press qw to switch the item.
f The items will switch each time you press the button.
[NORMAL]
Select this item when using the network function during standby.
[ECO]
Select this item to reduce power consumption during standby.
fProceed to Step 5) when [NORMAL] is selected.
5) Press as to select [QUICK STARTUP].
6) Press qw to switch the item.
f The items will switch each time you press the button.
[OFF]
Disables the [QUICK STARTUP] function.
[ON]
Enables the [QUICK STARTUP] function until the specied time set in [VALID PERIOD] elapses after
the projector enters the standby mode. The time until the projection starts after the power is turned on
will be reduced during the period when the [QUICK STARTUP] function is valid.
f Proceed to Step 7) when [ON] is selected.
7) Press the <ENTER> button.
fThe [QUICK STARTUP] screen is displayed.
8) Press qw to switch [VALID PERIOD].
f The items will switch each time you press the button.
[30MIN.]
Sets the time until the [QUICK STARTUP] function is disabled after the projector enters the standby
mode.
Select a desired valid period.
[60MIN.]
[90MIN.]
Note
fWhen [STANDBY MODE] is set to [NORMAL], the network function can be used during standby.
fWhen [STANDBY MODE] is set to [ECO], the network function and the audio output function cannot be used during standby. Also, some
RS-232C commands cannot be used.
fWhen [STANDBY MODE] is set to [ECO], it takes longer for the projection to start after the power is turned on, compared to when set to
[NORMAL].
f[STANDBY MODE] is xed to [NORMAL] when the [PROJECTOR SETUP] menu → [SCHEDULE] is set to [ON].
f[QUICK STARTUP] cannot be set when [STANDBY MODE] is set to [ECO].
fWhen [QUICK STARTUP] is set to [ON], the power consumption during standby becomes high during the period when the [QUICK
STARTUP] function is valid.
fIf [QUICK STARTUP] is set to [ON], the [QUICK STARTUP] function is disabled when the time set in [VALID PERIOD] elapses after the
projector enters the standby mode. The startup time and power consumption will be the same as when [QUICK STARTUP] is set to [OFF].
fWhen [QUICK STARTUP] is set to [ON], the power indicator <ON (G)/STANDBY (R)> blinks in red while in the standby mode during the
period when the [QUICK STARTUP] function is valid. When [IN STANDBY MODE] in [AUDIO SETTING] is set to [OFF], the power indicator
<ON (G)/STANDBY (R)> will change to a red light when the specied time set in [VALID PERIOD] elapses after the projector enters the
standby mode.
fWhen [QUICK STARTUP] is set to [ON], the period when the [QUICK STARTUP] function is valid will be added as the projector runtime.
[LightID]
Set the function to transmit the Light ID signal.
Manual
View the manual for the Panasonic PT-MZ770EJ here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 8.9. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-MZ770EJ or do you need help? Ask your question here
Need help?
Do you have a question about the Panasonic and is the answer not in the manual?
Question and answer
Number of questions: 0