Enables the function of the [PROJECTOR SETUP] menu → [ECO
MANAGEMENT] → [QUICK STARTUP].
[OFF]
Disables the function of the [PROJECTOR SETUP] menu → [ECO
MANAGEMENT] → [QUICK STARTUP].
[SHUTTER]
[OPEN]Disables the shutter function (shutter: open).
[CLOSE]Enables the shutter function (shutter: closed).
[INPUT]
[RGB1]Switches the input to RGB1.
[RGB2]Switches the input to RGB2.
[VIDEO]Switches the input to VIDEO.
[HDMI1]Switches the input to HDMI1.
[HDMI2]Switches the input to HDMI2.
[DIGITAL LINK]Switches the input to DIGITAL LINK.
[MEMORY VIEWER]Switches the input to MEMORY VIEWER.
[Panasonic APPLICATION]Switches the input to Panasonic APPLICATION.
[MIRRORING]
*1
Switches the input to MIRRORING.
[INPUT1] - [INPUT10]
*2
Switches the input to DIGITAL LINK, and switches the input of the
Panasonic twisted-pair-cable transmitter to the specied input.
[LIGHT POWER]
[NORMAL]Prioritizes luminance.
[ECO]
Controls the power to increase the life of the light source although
the luminance is lower than that of [NORMAL].
[QUIET]
Prioritizes the operation with less noise although the luminance is
lower than that of [NORMAL].
[IN STANDBY MODE(AUDIO)]
[OFF]Stops the audio output during standby.
[ON]Outputs the audio during standby.
[VOLUME][0] - [63]Sets the volume.
*1 [MIRRORING] is displayed when the optional Wireless Module (Model No.: ET-WM300) is attached.
*2 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reected from [INPUT1] to [INPUT10]. When an item that does not reect the input name is selected, it will be disabled.
11) Press the <ENTER> button.
fThe command is xed and n is displayed at the left of the selected command.
fAfter the command is xed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
fTo delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
fIf multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
fThe operating time will be the local time. (x page 118)
fIf an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
[RS-232C]
Set the communication condition of the <SERIAL IN> terminal. Refer to “<SERIAL IN> terminal” (x page 214).
1) Press as to select [RS-232C].
2) Press the <ENTER> button.
fThe [RS-232C] screen is displayed.
3) Press as to select [INPUT SELECT].
4) Press qw to switch the item.
[PROJECTOR]Performs the RS-232C communication with the <SERIAL IN> terminal of the projector.
[DIGITAL LINK]
Performs the RS-232C communication via the optional DIGITAL LINK output supported device (Model
No.: ET-YFB100G, ET-YFB200G) and the <DIGITAL LINK/LAN> terminal.
Manual
View the manual for the Panasonic PT-MZ670EJ here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-MZ670EJ or do you need help? Ask your question here
1024 x 768 (XGA),1280 x 1024 (SXGA),1280 x 720 (HD 720),1280 x 768 (WXGA),1280 x 800 (WXGA),1366 x 768,1400 x 1050 (SXGA+),1440 x 900 (WXGA+),1600 x 1200 (UXGA),1600 x 900,1680 x 1050 (WSXGA+),1920 x 1080 (HD 1080),1920 x 1200 (WUXGA)
Need help?
Do you have a question about the Panasonic and is the answer not in the manual?
Question and answer
Number of questions: 0