f The items will switch each time you press the button.
[NORMAL]Select this item when using the network function during standby.
[ECO]Select this item to reduce power consumption during standby.
fProceed to Step 5) when [NORMAL] is selected.
5) Press as to select [QUICK STARTUP].
6) Press qw to switch the item.
f The items will switch each time you press the button.
[OFF]Disables the [QUICK STARTUP] function.
[ON]
Enables the [QUICK STARTUP] function until the specied time set in [VALID PERIOD] elapses after
the projector enters the standby mode. The time until the projection starts after the power is turned on
will be reduced during the period when the [QUICK STARTUP] function is valid.
f Proceed to Step 7) when [ON] is selected.
7) Press the <ENTER> button.
fThe [QUICK STARTUP] screen is displayed.
8) Press qw to switch [VALID PERIOD].
f The items will switch each time you press the button.
[30MIN.]
Sets the time until the [QUICK STARTUP] function is disabled after the projector enters the standby
mode.
Select a desired valid period.
[60MIN.]
[90MIN.]
Note
fWhen [STANDBY MODE] is set to [NORMAL], the network function can be used during standby.
fWhen [STANDBY MODE] is set to [ECO], the network function and the audio output function cannot be used during standby. Also, some
RS-232C commands cannot be used.
fWhen [STANDBY MODE] is set to [ECO], it takes longer for the projection to start after the power is turned on, compared to when set to
[NORMAL].
f[STANDBY MODE] is xed to [NORMAL] when the [PROJECTOR SETUP] menu → [SCHEDULE] is set to [ON].
f[QUICK STARTUP] cannot be set when [STANDBY MODE] is set to [ECO].
fWhen [QUICK STARTUP] is set to [ON], the power consumption during standby becomes high during the period when the [QUICK
STARTUP] function is valid.
fIf [QUICK STARTUP] is set to [ON], the [QUICK STARTUP] function is disabled when the time set in [VALID PERIOD] elapses after the
projector enters the standby mode. The startup time and power consumption will be the same as when [QUICK STARTUP] is set to [OFF].
fWhen [QUICK STARTUP] is set to [ON], the power indicator <ON (G)/STANDBY (R)> blinks in red while in the standby mode during the
period when the [QUICK STARTUP] function is valid. When [IN STANDBY MODE] in [AUDIO SETTING] is set to [OFF], the power indicator
<ON (G)/STANDBY (R)> will change to a red light when the specied time set in [VALID PERIOD] elapses after the projector enters the
standby mode.
fWhen [QUICK STARTUP] is set to [ON], the period when the [QUICK STARTUP] function is valid will be added as the projector runtime.
[LightID]
Set the function to transmit the Light ID signal.
1) Press as to select [LightID].
2) Press qw to switch the item.
f The items will switch each time you press the button.
[OFF]Disables the Light ID function. The Light ID signal is not transmitted.
Manual
View the manual for the Panasonic PT-MZ670EJ here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-MZ670EJ or do you need help? Ask your question here
1024 x 768 (XGA),1280 x 1024 (SXGA),1280 x 720 (HD 720),1280 x 768 (WXGA),1280 x 800 (WXGA),1366 x 768,1400 x 1050 (SXGA+),1440 x 900 (WXGA+),1600 x 1200 (UXGA),1600 x 900,1680 x 1050 (WSXGA+),1920 x 1080 (HD 1080),1920 x 1200 (WUXGA)
Need help?
Do you have a question about the Panasonic and is the answer not in the manual?
Question and answer
Number of questions: 0