Twisted-pair-cable transmitter based on the communication standard HDBaseT
TM
such as the optional DIGITAL
LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) uses the twisted pair cable to transmit
input images, audio, Ethernet, and serial control signal, and the projector can input such digital signal to the
<DIGITAL LINK/LAN> terminal.
Computer
Computer cable (commercially
available)
Projector connecting terminals
Example of twisted-pair-cable transmitter
HDMI cable (commercially
available)
Hub
VCR (with built-in TBC)
Blu-ray disc player
Control computer
*1
*1 Control target is the projector or the twisted-pair-cable transmitter. The control itself may not be possible depending on the twisted-pair-cable
transmitter. Check the operating instructions of the device to be connected.
Attention
fAlways use one of the following when connecting a VCR.
gUse a VCR with built-in time base corrector (TBC).
gUse a time base corrector (TBC) between the projector and the VCR.
fThe image may be disrupted when nonstandard burst signal is connected. In such a case, connect the time base corrector (TBC) between
the projector and the external devices.
fAsk a qualied technician or your dealer to install the cable wiring between the twisted-pair-cable transmitter and the projector. Image may
be disrupted if cable transmission characteristics cannot be obtained due to inadequate installation.
fFor the LAN cable between the twisted-pair-cable transmitter and the projector, use a cable that meets the following criteria:
gConforming to CAT5e or higher standards
gShielded type (including connectors)
gStraight-through
gSingle wire
fWhen laying cables between the twisted-pair-cable transmitter and the projector, conrm that cable characteristics are compatible with
CAT5e or higher using tools such as a cable tester or cable analyzer.
When a relay connector is used, include it in the measurement.
fDo not use a hub between the twisted-pair-cable transmitter and the projector.
fWhen connecting to the projector using a twisted-pair-cable transmitter (receiver) of other manufacturers, do not place another twisted-pair-
cable transmitter between the twisted-pair-cable transmitter of other manufacturers and the projector. This may cause image to be disrupted.
fDo not pull cables forcefully. Also, do not bend or fold cables unnecessarily.
fTo reduce the effects of noise as much as possible, stretch out the cables between the twisted-pair-cable transmitter and the projector
without any loops.
fLay the cables between the twisted-pair-cable transmitter and the projector away from other cables, particularly power cables.
fWhen laying multiple cables, run them side by side along the shortest distance possible without bundling them together.
fAfter laying the cable, conrm that the value of [SIGNAL QUALITY] in the [NETWORK/USB] menu → [DIGITAL LINK STATUS] is displayed
in green, which indicates a normal quality. (x page 140)
Manual
View the manual for the Panasonic PT-MW630EJ here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 9.4. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-MW630EJ or do you need help? Ask your question here
1024 x 768 (XGA),1280 x 1024 (SXGA),1280 x 720 (HD 720),1280 x 768 (WXGA),1280 x 800 (WXGA),1366 x 768,1400 x 1050 (SXGA+),1440 x 900 (WXGA+),1600 x 1200 (UXGA),1600 x 900,1680 x 1050 (WSXGA+),1920 x 1080 (HD 1080),1920 x 1200 (WUXGA)
Need help?
Do you have a question about the Panasonic and is the answer not in the manual?
Question and answer
Number of questions: 0