Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 127 [SIGNAL INFORMA TION]
[INPUT] Displays the input terminal used for the projected image.
[SIGNAL FORMA T] Displays the format of the input signal.
[SIGNAL FREQUENCY] Displays the frequency of the input signal.
[SYNC.ST A TE] Displays the sync polarity of the input signal.
[V .SYNC WIDTH] Displays the vertical sync signal pulse width of the input signal.
[SCAN TYPE] Displays the scan type of the input signal.
[TOT AL DOTS] Displays the total dot count of the input signal.
[DISPLA Y DOTS] Displays the number of input signal display dots.
[TOT AL LINES] Displays the total line count of the input signal.
[DISPLA Y LINES] Displays the number of input signal display lines.
[SAMPLING] Displays the sampling information of the input signal.
[SIGNAL LEVEL] Displays the signal level of the input signal.
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
Note
f E-mail containing the status can be sent to the E-mail address (up to two addresses) set in “[E-mail set up] page” ( x page 171) by
pressing the <ENTER> button while the [ST A TUS] screen is displayed.
f There may be items that are displayed and items that are not displayed in [SIGNAL INFORMA TION] depending on the setting or the input
signal.
f If any abnormality has occurred on the projector , press the <DEF AUL T> button while the [ST A TUS] screen is displayed to display the detail
screen of the error information.
f For details on the contents displayed in [SELF TEST], refer to “[SELF TEST] display” (x page 207).
[DAT A CLONING] The menu setting and adjustment values of one projector can be copied to multiple projectors via LAN or using
the USB memory .
r Data that cannot be copied
Following menu settings and adjustment values are not copied. Set these in each projector .
f Menu lock password
f Security password
f Control device password
f The [PROJECTOR SETUP] menu → [PROJECT OR ID]
f The [PROJECTOR SETUP] menu → [DA TE AND TIME] → [ADJUST CLOCK]
f [NETWORK/USB] → [WIRED LAN]
f [NETWORK/USB] → [WIRELESS LAN]
f [NETWORK/USB] → [PROJECTOR NAME]
f The [PROJECTOR SETUP] menu → [DA T A CLONING] → [LAN] → [WRITE PROTECT]
f Password set in “[Change password] page” ( x page 175) of the web control screen
f “[E-mail set up] page” ( x page 171) in the web control screen
f “[Authentication set up] page” ( x page 172) in the web control screen
f “[Crestron Connected(TM)] page” ( x page 176) in the web control screen
r Supported device
f Commercially available USB memory is supported.
The USB memory with a security function is not supported.
f Only the cards formatted in F A T16 or F A T32 can be used.
f Only the single partition structure is supported.
Note
f The cloning function will not operate when the models of the projectors are different. Use between the same model.
f Set the input to anything other than MEMORY VIEWER, and then execute [DA T A CLONING].
f When the data cloning function is used, the light source indicator <LIGHT>, the temperature indicator <TEMP>, and the lter indicator
<FIL TER> will blink while copying the data. Wait until the blinking of the indicator is stopped.
Copying the data to other projector via LAN Set the projector to copy the data as follows in advance.
f The [PROJECTOR SETUP] menu → [DA T A CLONING] → [LAN] → [WRITE PROTECT] → [OFF]
Need help?
Do you have a question about the Panasonic and is the answer not in the manual?
Question and answer
Number of questions: 0