Panasonic PT-MW630EJ manual

Panasonic PT-MW630EJ
9.4 · 1
PDF manual
 · 229 pages
English
manualPanasonic PT-MW630EJ

Chapter 4Settings — [PROJECTOR SETUP] menu

ENGLISH - 117

[EXTERNAL CONTROL]
Transmits the Light ID signal set by the user.
Select this item when the Light ID signal transmitted by the projector is switched using the contents
list distribution function or the Light ID control function of the “Multi Monitoring & Control Software”.
To set the Light ID, it is necessary to purchase the Light ID. To purchase the Light ID, visit the
Panasonic website (https://panasonic.net/cns/LinkRay/).
The Light ID which the user has set is erased in following cases.
f When the <MAIN POWER> switched is set to <OFF>
[INTERNAL ID]
Transmits the internal Light ID signal.
The Light ID signal is linked to the Panasonic website (https://panasonic.net/cns/projector/) in the
factory default setting or after the [PROJECTOR SETUP] menu [INITIALIZE] is executed.
When the Light ID is set while [LightID] is set to [INTERNAL ID], the Light ID signal set by the user is
transmitted.
Note
f When the [PROJECTOR SETUP] menu [ECO MANAGEMENT] [LIGHT POWER] is set to anything other than [NORMAL], the
[LightID] setting is disabled and xed to [OFF].
f The light output is decreased when [LightID] is set to anything other than [OFF].
When clogging of the lter is detected and the brightness of the light source is restricted, [LightID] will be xed to [OFF].
f Following setting will be disabled and it will be xed to [OFF] when [LightID] is set to anything other than [OFF].
g The [PICTURE] menu [DYNAMIC CONTRAST]
g The [PROJECTOR SETUP] menu [ECO MANAGEMENT] [AMBIENT LIGHT DETECTION] and [SIGNAL DETECTION]
f To set the Light ID signal, use “Multi Monitoring & Control Software”. The software can be downloaded from the Panasonic website (https://
panasonic.net/cns/projector/).
f The internal Light ID signal can be rewritten by executing the control command using the “Multi Monitoring & Control Software”. For details
of executing the control command, refer to the Operating Instructions of “Multi Monitoring & Control Software”.
f When the [PROJECTOR SETUP] menu [INITIALIZE] [ALL USER DATA] is executed, the [LightID] setting is reset to the factory default.
f For details of the contents list distribution function and Light ID control function of “Multi Monitoring & Control Software”, refer to the
Operating Instructions of “Multi Monitoring & Control Software”.
f The projected image may icker when the Light ID signal is transmitted, but this is caused luminance change during the transmission of the
Light ID, and it is not a malfunction.
f When clogging of the lter is detected and the brightness of the light source is restricted, the lter indicator <FILTER> lights up and [LightID]
is set to [OFF], and the Light ID signal will not be transmitted. Set it again after cleaning the clogged lter.
For details on how to solve the lter clogging, refer to “When an indicator lights up” (x page 197).

[INITIAL STARTUP]

Set the startup method when the <MAIN POWER> switch is set to <ON>.

1) Press as to select [INITIAL STARTUP].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[LAST MEMORY] Starts up the projector in the condition before the <MAIN POWER> switch is set to <OFF>.
[STANDBY] Starts up the projector in standby.
[ON] Starts projecting immediately.

[STARTUP INPUT SELECT]

Set the input when the projector is switched on to start projection.

1) Press as to select [STARTUP INPUT SELECT].

2) Press the <ENTER> button.

f The [STARTUP INPUT SELECT] screen is displayed.
3) Press asqw to select the input, and press the <ENTER> button.
[LAST USED] Keeps the input selected last.
[RGB1] Sets the input to RGB1.
[RGB2] Sets the input to RGB2.
[VIDEO] Sets the input to VIDEO.
[HDMI1] Sets the input to HDMI1.
[HDMI2] Sets the input to HDMI2.
[DIGITAL LINK] Sets the input to DIGITAL LINK.
[MEMORY VIEWER] Sets the input to MEMORY VIEWER.
[Panasonic APPLICATION] Sets the input to Panasonic APPLICATION.

Manual

View the manual for the Panasonic PT-MW630EJ here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 9.4. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-MW630EJ or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Panasonic and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Panasonic PT-MW630EJ specifications

Below you will find the product specifications and the manual specifications of the Panasonic PT-MW630EJ.

General
BrandPanasonic
ModelPT-MW630EJ | PT-MW630EJ
Productvideo projector
EAN5025232870622
LanguageEnglish
FiletypeUser manual (PDF)
Weight & dimensions
Weight16900 g
Width560 mm
Depth428 mm
Height185 mm
Package width776 mm
Package depth587 mm
Package height362 mm
Package weight25600 g
Projector
Projector brightness6500 ANSI lumens
Projection technology3LCD
Projector native resolutionWXGA (1280x800)
Contrast ratio (typical)-
Contrast ratio (dynamic)3000000:1
Native aspect ratio16:10
Screen size compatibility40 - 400 "
Supported aspect ratios4:3, 16:10, 16:9
Projection distance- m
Uniformity90 %
Keystone correction, horizontal-25 - 25 °
Keystone correction, vertical-30 - 30 °
Matrix size0.76 "
Vertical scan range24 - 100 Hz
Horizontal scan range15 - 91 kHz
Features
HDCPYes
On Screen Display (OSD) languagesARA, DAN, DEU, DUT, ENG, ESP, FIN, FRE, HUN, ITA, JPN, KAZ, NOR, POL, POR, RUM, RUS, SWE, THA, TUR, VIE
Preset modesBlackboard, Cinema, Dynamic, Standard, Whiteboard
On Screen Display (OSD)Yes
Dot clock scanning frequency162 MHz
Air filterYes
Sync-on-green (SOG)Yes
Password protectionYes
Password protection typeSupervisor, User
Noise level32 dB
Multimedia
Built-in speaker(s)Yes
Number of built-in speakers1
RMS rated power10 W
Image formats supportedBMP, JPEG, JPG
Video formats supportedAVC, AVI, H.264, M-JPEG, MOV, MP4, MPEG, MPEG2, MPEG4, MPG, WMV, WMV9
Audio formats supportedAAC, LC-AAC, LPCM, MP3, WMA
Light source
Service life of light source20000 h
Light source typeLaser
Design
Product typeLarge venue projector
Product colorWhite
Housing materialABS, Polycarbonate (PC)
LED indicatorsYes
PlacementDesktop, Ceiling
Lens system
Focal length range26.8 - 45.5 mm
Aperture range (F-F)1.7 - 2.3
Horizontal lens shift range-35 - 35 %
Vertical lens shift range-67 - 67 %
Throw ratio1.6 - 2.8:1
Display
Built-in display-
Power
Power sourceAC
Power consumption (typical)505 W
Power consumption (standby)22 W
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Video
Analog signal format systemNTSC, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM
Full HDNo
3D-
Supported video modes480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Supported graphics resolutions1024 x 768 (XGA),1280 x 1024 (SXGA),1280 x 720 (HD 720),1280 x 768 (WXGA),1280 x 800 (WXGA),1366 x 768,1400 x 1050 (SXGA+),1440 x 900 (WXGA+),1600 x 1200 (UXGA),1600 x 900,1680 x 1050 (WSXGA+),1920 x 1080 (HD 1080),1920 x 1200 (WUXGA)
Ports & interfaces
VGA (D-Sub) ports quantity2
HDMI ports quantity2
Component video (YPbPr/YCbCr) in1
Composite video in1
DVI portNo
HDMI connector typeFull-size
HDBaseT portYes
USB 2.0 ports quantity2
Audio (L/R) in1
Headphone outputs1
Microphone inYes
Serial interface typeRS-232
S-Video inputs quantity0
BNC input ports5
PC in (D-Sub)Yes
Network
Ethernet LAN (RJ-45) ports2
Smart TV-
Ethernet LANYes
Wi-Fi-
Ethernet LAN data rates10, 100 Mbit/s
Software
Windows operating systems supportedYes
Mac compatibilityYes
Mac operating systems supportedYes
Mobile operating systems supportedAndroid, iOS
Operational conditions
Operating temperature (T-T)0 - 45 °C
Operating relative humidity (H-H)20 - 80 %
Other features
RS-232 ports1
Packaging content
Handheld remote controlYes
Remote control typeIR
Batteries includedYes
ManualYes
Storage
Card reader integratedNo
Optical disc player typeNot included
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Panasonic PT-MW630EJ below.

What is the weight of the Panasonic PT-MW630EJ?

The Panasonic PT-MW630EJ has a weight of 16900 g.

What is the height of the Panasonic PT-MW630EJ?

The Panasonic PT-MW630EJ has a height of 185 mm.

What is the width of the Panasonic PT-MW630EJ?

The Panasonic PT-MW630EJ has a width of 560 mm.

What is the depth of the Panasonic PT-MW630EJ?

The Panasonic PT-MW630EJ has a depth of 428 mm.

Is the manual of the Panasonic PT-MW630EJ available in English?

Yes, the manual of the Panasonic PT-MW630EJ is available in English .

Is your question not listed? Ask your question here

No results