Panasonic PT-F100NTE manual

Panasonic PT-F100NTE
9.4 · 1
PDF manual
 · 56 pages
English
manualPanasonic PT-F100NTE

OPTION menu

ENGLISH - 37

Settings
You can check how long the lamp has been used.
You can set the off timer to switch off the POWER of the
projector after a certain period of time automatically
when no signal is detected. Press I H to select the
required period from 15 to 60 minutes at intervals of 5 minutes.You can switch the projector start up status for when the
Mains lead is connected while the MAIN POWER is on,
or for when the MAIN POWER is switched on while the
Mains lead is connected. Press I H to select the
required option.
OFF The projector will start from the
standby mode or the projecting
mode.
ON The projector will start from the
projecting mode.
You can turn off the function of the control panel buttons
on the projector body. Press I H to select the required
option.
INVALID Invalidate the control panel buttons
Confirmation screen will be
displayed.
VALID Validate the control panel buttons
You can turn off the AUTO SETUP function for when the COMPUTER signal is detected.
AUTO When the projector detect a
COMPUTER signal, adjust the
projected image position
automatically for SIGNAL SEARCH,
DOT CLOCK and CLOCK PHASE.
BUTTON Only when the AUTO SETUP button
is pressed, the projected image
position will be adjusted for DOT
CLOCK and CLOCK PHASE. See
“Remote control” on page 13.
You can turn off the auto signal detecting system.
ON Detect the input signal from the
terminals and project the image.
OFF Deactive
When installing the projector, select the projection
method according to the projector position. Press I H
to cycle through the options. See “Projection method” on page 17.

LAMP RUNTIME

NOTE:
LAMP RUNTIME is a relevant matter for lamp
replacement timing. See “Replacing the Lamp unit” on
page 43.
When the lamp unit is replaced with the new one
(ET-LAF100), the setting will be reset to “0”.

POWER OFF TIMER

DIRECT POWER ON

NOTE:
When the projector is started from the projecting mode,
pressing the POWER button procedure is skippable.
DISABLE
15 MIN.
20 MIN.
25 MIN.
30 MIN.
35 MIN.
60 MIN.
55 MIN.
50 MIN.
45 MIN.
40 MIN.

CONTROL PANEL

AUTO SETUP

NOTE:
Usually the recommended setting is AUTO.

SIGNAL SEARCH

NOTE:
SIGNAL SEARCH is not available when any input
signal is projecting.
Usually the recommended setting is ON.

INSTALLATION

FRONT/DESKSetting on a desk/floor and projecting from frontFRONT/CEILINGMounting in the ceiling and projecting from frontREAR/DESKSetting on a desk/floor and projecting from rearREAR/CEILINGMounting in the ceiling and projecting from rear

Manual

View the manual for the Panasonic PT-F100NTE here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 9.4. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-F100NTE or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Panasonic and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Panasonic PT-F100NTE specifications

Below you will find the product specifications and the manual specifications of the Panasonic PT-F100NTE.

General
BrandPanasonic
ModelPT-F100NTE
Productvideo projector
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Panasonic PT-F100NTE below.

Is the manual of the Panasonic PT-F100NTE available in English?

Yes, the manual of the Panasonic PT-F100NTE is available in English .

Is your question not listed? Ask your question here

No results