Panasonic PT-DZ6710E manual

Panasonic PT-DZ6710E
8.2 · 1
PDF manual
 · 42 pages
English
manualPanasonic PT-DZ6710E

ENGLISH - 28

Maintenance

Monitor Lamp indicators

If a problem should occur with the projector, the indicators will inform you. Manage the indicated problems as follow.
1. Confirm the status of all indicators and projector, and switch off the projector in proper way.
2. Find out the cause of the problem by status of each indicator.
3. Follow the instruction for each indication below and solve the problem.
4. Turn on the projector in the correct way and confirm the indicator is not indicating a problem any longer.
LAMP1/LAMP2 indicator
TEMP indicator

Managing the indicated problems

NOTE:
If no problem is found or the problem remains, do not turn on the projector. Instead contact your nearest dealer.
Lamp
indication
Information Check point Remedial measure
Lighting in red
Indicates the time for
replacing the lamp unit
Did you notice a “REPLACE
LAMP” message on the screen
when turning on the projector
power supply?
This lamp monitor lights up when the lamp
unit used hours have reached 1 800* hours.
Request the dealer to replace the lamp unit.
* 2 800 hours for PT-D5000E only.
Blinking in red
once
Lamp unit is not installed.
Check the lamp unit
compartment.
Install the lamp unit.
When lamp unit is installed and still having
the indicator lights, contact to the dealer.
Blinking in red
3 times
Error is detected in the
lamp circuit.
Did you turn the power back on
immediately after turning it off?
Wait until the lamp has cooled off, and then
turn on the power.
Some error has arisen in the
lamp circuit.
Check for fluctuation (or drop) in
the source voltage.
Turn off the POWER switch of the projector
properly and contact your nearest dealer.
Lamp
indication
Information Check point Remedial measure
Lighting in red
Warm-up status
Did you turn on the power when
the ambient temperature was
lower than approx. 0 °C (32 °F)?
Wait about 5 minutes in the current status.
Install the unit in a location having an
ambient temperature from 0 °C (32 °F) -
45 °C (113 °F).
High temperature inside.
(WARNING)
Check the ventilation port is
blocked.
Is the room air temperature too
high?
Was the temperature warning
indication displayed?
Remove the object that is blocking the
ventilation port.
Move the projector to a temperature of 0 °C
(32 °F) - 45 °C (113 °F) and the humidity of
20 % to 80 % (no condensation).
Turn off the POWER switch of the projector
in proper way and contact the dealer.
Blinking in red
once
The filter is excessively
dirty and the ventilation is
poor.
Blinking in red
twice
High temperature inside.
(Standby condition)
Blinking in red
3 times
Cooling fan has been
stopped.
Turn off the POWER switch of the projector
in proper way and contact the dealer.
STANDBY(RED)/STANDBY(RED)/
ON(GREEN) ON(GREEN)
LAMPLAMP TEMPTEMP
FILTERFILTER
STANDBY(RED)/STANDBY(RED)/
ON(GREEN) ON(GREEN)
LAMPLAMP TEMPTEMP
FILTERFILTER
Indicators
Power indicator
Lamp1 (LAMP1) indicator
Lamp2 (LAMP2) indicator
Temperature (TEMP) indicator
Filter (FILTER) indicator

Manual

View the manual for the Panasonic PT-DZ6710E here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 8.2. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-DZ6710E or do you need help? Ask your question here

Need help?

Do you have a question about the Panasonic and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Panasonic PT-DZ6710E specifications

Below you will find the product specifications and the manual specifications of the Panasonic PT-DZ6710E.

General
BrandPanasonic
ModelPT-DZ6710E | PT-DZ6710E
Productvideo projector
EAN5025232492282, 5052179605420
LanguageEnglish
FiletypeUser manual (PDF)
Projector
Projector brightness6000 ANSI lumens
Projection technologyDLP
Projector native resolutionWUXGA (1920x1200)
Contrast ratio (typical)2000:1
Uniformity90 %
Vertical scan range50 - 85 Hz
Horizontal scan range15 - 91 kHz
Screen size compatibility50 - 600 "
Projection distance- m
Other features
Aspect ratio16:10
RS-232 ports1
Dimensions (WxDxH)498 x 440 x 175 mm
Non-operating relative humidity (non-condensing)20 - 80 %
Connectivity technologyWired
Power requirements220 – 240 V AC 50/60 Hz
Video inBNC
Light source
Lamp power300 W
Lamp typeUHM
Service life of light source- h
Light source typeLamp
Features
Dot clock scanning frequency162 MHz
Noise level- dB
Video
Full HDYes
Analog signal format systemNTSC, PAL, SECAM
3D-
Ports & interfaces
VGA (D-Sub) ports quantity2
S-Video inputs quantity1
Component video (YPbPr/YCbCr) in2
DVI portYes
Composite video in-
Audio (L/R) in-
USB 2.0 ports quantity-
HDMI ports quantity-
Serial interface typeRS-232
Network
Ethernet LAN (RJ-45) ports1
Ethernet LANYes
Wi-Fi-
Weight & dimensions
Weight16000 g
Power
Power consumption (typical)800 W
Power consumption (standby)9 W
Operational conditions
Operating temperature (T-T)0 - 45 °C
Packaging content
Handheld remote controlYes
Lens system
Zoom ratio-
Focal length range- mm
Multimedia
Built-in speaker(s)-
Design
Product colorBlack
PlacementCeiling
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Panasonic PT-DZ6710E below.

What is the weight of the Panasonic PT-DZ6710E?

The Panasonic PT-DZ6710E has a weight of 16000 g.

Is the manual of the Panasonic PT-DZ6710E available in English?

Yes, the manual of the Panasonic PT-DZ6710E is available in English .

Is your question not listed? Ask your question here

No results