Panasonic PT-DZ6710E manual

Panasonic PT-DZ6710E
8.2 · 1
PDF manual
 · 42 pages
English
manualPanasonic PT-DZ6710E

ENGLISH - 19

Basic Operation

Projecting

Switching on the projector
When using an optional lens, install a projection lens before switch on the projector.1. Connect the supplied mains lead (220 - 240 V AC, 50 Hz/60 Hz) to the AC IN terminal.2. Remove the projection lens cover from the lens.3. Switch the POWER switch on that is on the side of the projector.
The power indicator lamp on the projector will flash in red.
After a short period, the indicator will illuminate and the
projector will enter standby mode.
4. Press the POWER ON button
The power indicator lamp illuminates in green and soon the
image is projected on the screen.
.
Making adjustment and selection
It is recommended that the projector be allowed to warm up for at least 30 minutes before any adjustments are made to the focus.1. Roughly adjust the focus of the lens.2. Select and set the projection scheme of
INSTALLATION and COOLING CONDITION settings in
PROJECTOR SETUP menu.3. Select the input signal by pressing the INPUT SELECT buttons.4. Adjust the vertical tilt of the projector with the front leg adjusters.5. Adjust the shift position of the projection.
If the input signal is RGB signal, additionally press the
AUTO SETUP button to adjust the position of the image.
6. Zoom the lens so the image fills the screen.7. Readjust the focus.8. Readjust the zoom so that the image size fits in the screen.Adjusting focus, zoom and shift

Projecting a image

NOTE:
If the projector is powered up at about 0 °C (32 °F), a warm-
up period of approximately 5 minutes may be necessary to
start projection. The temperature monitor (TEMP) lamp lights
up during the warm-up period. When the warm-up is
completed, the temperature monitor (TEMP) lamp turns off
and the image is projected on the screen.
If the temperature of the operating environment is low and
warm-up takes more than 5 minutes, the projector will judge
that a problem has occurred and the power will be turned off
automatically. If this happens, increase the temperature
around the projector so that it is
0 °C (32 °F) or higher, and
then turn on the POWER switch and press the POWER ON
button again.
POWER switchAC IN terminal
POWER ON button
Control buttons of the
projector
Pressing the LENS button changes the
setup screen in order of FOCUS, ZOOM
and SHIFT. Press F G I H to adjust.
Remote control buttons
Press FOCUS, ZOOM or SHIFT button
to display the setup screen. Press F G
I H to adjust.
CAUTION:
Be careful not to catch your fingers between the lens and
shroud when shifting the lens.
NOTE:
The setup screen will be displayed with the optional fixed lens
though, it will not be functioning.
Pressing F G I or H for 3 seconds or more, performance
the adjustment faster.
LENS buttonINPUT SELECT buttons

Manual

View the manual for the Panasonic PT-DZ6710E here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 8.2. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-DZ6710E or do you need help? Ask your question here

Need help?

Do you have a question about the Panasonic and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Panasonic PT-DZ6710E specifications

Below you will find the product specifications and the manual specifications of the Panasonic PT-DZ6710E.

General
BrandPanasonic
ModelPT-DZ6710E | PT-DZ6710E
Productvideo projector
EAN5025232492282, 5052179605420
LanguageEnglish
FiletypeUser manual (PDF)
Projector
Projector brightness6000 ANSI lumens
Projection technologyDLP
Projector native resolutionWUXGA (1920x1200)
Contrast ratio (typical)2000:1
Uniformity90 %
Vertical scan range50 - 85 Hz
Horizontal scan range15 - 91 kHz
Screen size compatibility50 - 600 "
Projection distance- m
Other features
Aspect ratio16:10
RS-232 ports1
Dimensions (WxDxH)498 x 440 x 175 mm
Non-operating relative humidity (non-condensing)20 - 80 %
Connectivity technologyWired
Power requirements220 – 240 V AC 50/60 Hz
Video inBNC
Light source
Lamp power300 W
Lamp typeUHM
Service life of light source- h
Light source typeLamp
Features
Dot clock scanning frequency162 MHz
Noise level- dB
Video
Full HDYes
Analog signal format systemNTSC, PAL, SECAM
3D-
Ports & interfaces
VGA (D-Sub) ports quantity2
S-Video inputs quantity1
Component video (YPbPr/YCbCr) in2
DVI portYes
Composite video in-
Audio (L/R) in-
USB 2.0 ports quantity-
HDMI ports quantity-
Serial interface typeRS-232
Network
Ethernet LAN (RJ-45) ports1
Ethernet LANYes
Wi-Fi-
Weight & dimensions
Weight16000 g
Power
Power consumption (typical)800 W
Power consumption (standby)9 W
Operational conditions
Operating temperature (T-T)0 - 45 °C
Packaging content
Handheld remote controlYes
Lens system
Zoom ratio-
Focal length range- mm
Multimedia
Built-in speaker(s)-
Design
Product colorBlack
PlacementCeiling
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Panasonic PT-DZ6710E below.

What is the weight of the Panasonic PT-DZ6710E?

The Panasonic PT-DZ6710E has a weight of 16000 g.

Is the manual of the Panasonic PT-DZ6710E available in English?

Yes, the manual of the Panasonic PT-DZ6710E is available in English .

Is your question not listed? Ask your question here

No results