Panasonic PT-DZ12000E manual

Panasonic PT-DZ12000E
5.5 · 1
PDF manual
 · 128 pages
English
manualPanasonic PT-DZ12000E

80

ENGLISH

Projector setup (continued)

Lamp relay

If using the projector for a continuous period of
24 hours or more, this setting can be used to
automatically switch the lamps that are turned on in
order to reduce the lamp deterioration that can occur
as a result of continuous use.
“LAMP RELAY” will only be enabled when the lamp
selection is “SINGLE” (1 lamp), “DUAL” (2 lamps),
“TRIPLE” (3 lamps) or “QUAD” (4 lamps).
Press ▲▼ to select “LAMP 1.
RELAY”.
LAMP SELECT
LAMP RELAY
RS-232C
QUAD
OFF
Press ◄► to switch “LAMP 2.
RELAY”.
The time interval for lamps to be switched will
change as shown in the diagram below each
time ◄► is pressed.
01:00
00:00OFF
23:00
(Units of 1 hour)
Note
The lamps will switch at the specified time when the
lamp selection is “SINGLE” or “DUAL”.
When the lamp selection is “TRIPLE”, the lamps will
switch a total of three times at two-hour intervals
starting from the specified time, and after this the
previous operating status will be maintained until
the next specified time is reached.
When the lamp selection is “QUAD”, three lamps
will illuminate from the specified time, and the three
lamps will switch a total of four times at two-hour
intervals from that time. After this, four lamps will
illuminate for eight hours from the specified time,
and then when the next specified time is reached,
switching between three lamps will resume.
The setting time will be the local time. (p. 83)

RS-232C setting

This sets communication parameters for the
projector. (p. 106)
Press ▲▼ to select “RS-232C”.1.
LAMP RELAY
RS-232C
REMOTE2 MODE
OFF
DEFAULT
Press ENTER.2.
The “RS-232C” screen will be displayed.
RS-232C
SERIAL IN
(IN) BAUDRATE
(IN) PARITY
(OUT) BAUDRATE
(OUT) PARITY
RESPONSE(ID ALL)
GROUP
RESPONSE(ID GROUP)
RS-232C
9600
NONE
9600
NONE
ON
MASTER
ON
Press ▲▼ to select “SERIAL IN”.3.
Press ◄► to switch “SERIAL 4.
IN”.
The setting will change as follows each time
◄► is pressed.
RS-232C RS-422
Press ▲▼ to select 5.
communication conditions.
Press ◄► to confirm the setting.6.
Press MENU three times.7.
The on-screen indications disappear, and the
system returns to the normal screen.

Remote2 mode

This sets the REMOTE2 terminal. (p. 110)
Press ▲▼ to select “REMOTE2 1.
MODE”.
RS-232C
REMOTE2 MODE
STATUS
DEFAULT
Press ◄► to switch “REMOTE2 2.
MODE”.
The setting will change as follows each time
◄► is pressed.
DEFAULT USER
DEFAULT:
The pin assignment of the REMOTE2 terminal is
used as the projector default setting. (p. 110)
USER:
This is used for changing an optional input module,
using the REMOTE2 terminal, or for changing the
settings for the REMOTE2 terminal. Any settings
you make for pins 2 to 8 become valid once you
press the ENTER button.

Manual

View the manual for the Panasonic PT-DZ12000E here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 5.5. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-DZ12000E or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Panasonic and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Panasonic PT-DZ12000E specifications

Below you will find the product specifications and the manual specifications of the Panasonic PT-DZ12000E.

General
BrandPanasonic
ModelPT-DZ12000E | PT-DZ12000E
Productvideo projector
EAN5052178257828
LanguageEnglish
FiletypeUser manual (PDF)
Projector
Projector brightness12000 ANSI lumens
Projection technologyDLP
Projector native resolutionWUXGA (1920x1200)
Contrast ratio (typical)5000:1
Projection distance1.1 - 103.3 m
Number of colors16.78 million colors
Vertical scan range24 - 120 Hz
Horizontal scan range15 - 100 kHz
Other features
Aspect ratio16:10
RS-232 ports1
Dimensions (WxDxH)578 x 320 x 643 mm
Light source
Lamp power300 W
Lamp typeUHM
Light source typeLamp
Ports & interfaces
VGA (D-Sub) ports quantity1
S-Video inputs quantity1
Composite video in1
DVI portYes
Serial interface typeRS-232
Network
Ethernet LAN (RJ-45) ports1
Weight & dimensions
Weight35000 g
Power
Power consumption (typical)1500 W
Operational conditions
Operating relative humidity (H-H)10 - 80 %
Operating temperature (T-T)0 - 45 °C
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Panasonic PT-DZ12000E below.

What is the weight of the Panasonic PT-DZ12000E?

The Panasonic PT-DZ12000E has a weight of 35000 g.

Is the manual of the Panasonic PT-DZ12000E available in English?

Yes, the manual of the Panasonic PT-DZ12000E is available in English .

Is your question not listed? Ask your question here

No results