Panasonic PT-DZ12000E manual

Panasonic PT-DZ12000E
5.5 · 1
PDF manual
 · 128 pages
English
manualPanasonic PT-DZ12000E

38

ENGLISH

Projection (continued)

Powering up the projector

1
Connect the supplied power
cable. (220 V-240 V, 50 Hz/60 Hz)
2
Press the “ | ” marked side of the
MAIN POWER switch to turn on
the power.
The power indicator lamp on the projector will
flash in red. After a short period, the indicator
will illuminate and the projector will enter
standby mode.
3
Press POWER ON “ | ”.
The power indicator lamp illuminates in green
and soon the image is projected on the screen.
Note
If the projector is powered up at about 0 °C, a
warm-up period of approximately 5 minutes may
be necessary to start projection. The temperature
monitor (TEMP) lamp lights up during the warm-up
period. When the warm-up is completed, the
temperature monitor (TEMP) lamp turns off and the
image is projected on the screen.
If the temperature of the operating environment is
low and warm-up takes more than 5 minutes, the
projector will judge that a problem has occurred
and the power will be turned off automatically. If
this happens, increase the temperature around the
projector so that it is 0 °C or higher, and then turn
on the MAIN POWER switch and the POWER ON
“ | ” switch once more.

Making adjustment and

selection

4
Roughly adjust the focus of the
lens. (p. 40)
5
Select and set the projection
scheme. (p. 78)
6
Select the input signal by
pressing the input selector
button to toggle through RGB1,
RGB2, DVI-D, VIDEO, S-VIDEO
and AUX. (p. 48)
The AUX button is disabled when an optional
input module is not connected.
7
Adjust the tilt of the main unit in
front and rear or right and left.
(p. 20)
8
Adjust the shift. (p. 40)
9
Press AUTO SETUP if the input
signal is RGB signal. (p. 49)
j
Fit the image size to the screen
size. (p. 40)
k
Adjust the focus. (p. 40)
l
Readjust the zoom so that the
image size fits in the screen.
(p. 40)
12 7
9
63 5
5
6
8
j
3
9
4
,
8
-
l
4
,
k

Manual

View the manual for the Panasonic PT-DZ12000E here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 5.5. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-DZ12000E or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Panasonic and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Panasonic PT-DZ12000E specifications

Below you will find the product specifications and the manual specifications of the Panasonic PT-DZ12000E.

General
BrandPanasonic
ModelPT-DZ12000E | PT-DZ12000E
Productvideo projector
EAN5052178257828
LanguageEnglish
FiletypeUser manual (PDF)
Projector
Projector brightness12000 ANSI lumens
Projection technologyDLP
Projector native resolutionWUXGA (1920x1200)
Contrast ratio (typical)5000:1
Projection distance1.1 - 103.3 m
Number of colors16.78 million colors
Vertical scan range24 - 120 Hz
Horizontal scan range15 - 100 kHz
Other features
Aspect ratio16:10
RS-232 ports1
Dimensions (WxDxH)578 x 320 x 643 mm
Light source
Lamp power300 W
Lamp typeUHM
Light source typeLamp
Ports & interfaces
VGA (D-Sub) ports quantity1
S-Video inputs quantity1
Composite video in1
DVI portYes
Serial interface typeRS-232
Network
Ethernet LAN (RJ-45) ports1
Weight & dimensions
Weight35000 g
Power
Power consumption (typical)1500 W
Operational conditions
Operating relative humidity (H-H)10 - 80 %
Operating temperature (T-T)0 - 45 °C
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Panasonic PT-DZ12000E below.

What is the weight of the Panasonic PT-DZ12000E?

The Panasonic PT-DZ12000E has a weight of 35000 g.

Is the manual of the Panasonic PT-DZ12000E available in English?

Yes, the manual of the Panasonic PT-DZ12000E is available in English .

Is your question not listed? Ask your question here

No results