[NATIVE]Forcibly displays 2D images regardless of input image signals.
[SIMULTANEOUS]
*2
Forcibly displays 3D images in simultaneous system regardless of input video signals.
[SIDE BY SIDE]Forcibly displays 3D images in side by side format regardless of input image signals.
[TOP AND BOTTOM]Forcibly displays 3D images in top and bottom format regardless of input image signals.
[LINE BY LINE]
*3
Forcibly displays 3D images in line by line system regardless of input video signals.
[FRAME SEQUENTIAL]
*4
Forcibly displays 3D images in frame sequential format regardless of input image signals.
*1 During DVI-D, HDMI, or DIGITAL LINK input only
*2 During 3G-SDI level B input only
*3 Only while signals other than interlaced signals are input
*4 Only while progressive signals with the vertical scanning frequency of 100 Hz or 120 Hz are input to the <RGB1>/<RGB2>/<DVI-D> terminals
4) Press the <ENTER> button.
Note
fWhen set to [AUTO], [SIMULTANEOUS], [SIDE BY SIDE], [TOP AND BOTTOM], [LINE BY LINE], or [FRAME SEQUENTIAL], 3D images
are not displayed in [3D SIMUL INPUT SETTING]. In [AUTO], however, this only occurs when 3D format can be recognized.
fThis may not function properly for some connected external devices.
[3D 24Hz IMAGE PROJECTION]
(Only for PT-DZ870E)
Set the output frame rate when a 3D signal with the vertical scanning frequency of 24 Hz is input.
1) Press as to select [3D 24Hz IMAGE PROJECTION].
2) Press qw to switch the item.
fThe items will switch each time you press the button.
[144fps]Displays images with the frame rate of 144 fps.
[96fps]Displays images with the frame rate of 96 fps.
Note
fThis function is enabled only when a 3D signal with the vertical scanning frequency of 24 Hz is input. The [3D 24Hz IMAGE PROJECTION]
setting can be changed even when the corresponding signal is not input.
fWhen [3D 24Hz IMAGE PROJECTION] is set to [144fps], [SCREEN SETTING] (x page 96) cannot be selected. [SCREEN FORMAT] is
xed to [16:9] and [SCREEN POSITION] cannot be adjusted. Adjust the image position using [3D 24Hz IMAGE POSITION].
fWhen [3D 24Hz IMAGE PROJECTION] is set to [144fps], the image may not be displayed correctly if the function of [CUSTOM MASKING]
(x page 84), [EDGE BLENDING] (x page 86), [UNIFORMITY] (x page 103), or [DISPLAY SETTING] (x page 131) is used.
[3D 24Hz IMAGE POSITION]
(Only for PT-DZ870E)
Set the image position when a 3D signal with the vertical scanning frequency of 24 Hz is input.
1) Press as to select [3D 24Hz IMAGE POSITION].
2) Press qw to adjust the position.
fAdjust the vertical position between
-
60 and +60.
Note
fThe position can be adjusted only when [3D 24Hz IMAGE PROJECTION] is set to [144fps] and a 3D signal with the vertical scanning
frequency of 24 Hz is input.
[LEFT/RIGHT SWAP]
Display images by inverting the timing of horizontal image switching. Change the settings when there is something wrong with the 3D image
being viewed.
1) Press as to select [LEFT/RIGHT SWAP].
2) Press qw to switch the item.
fThe items will switch each time you press the button.
[NORMAL]Do not change the [NORMAL] setting if the 3D images are displayed correctly.
[SWAPPED]Select this when left and right 3D images are swapped to be displayed.
Manual
View the manual for the Panasonic PT-DX100EWJ here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 6.9. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-DX100EWJ or do you need help? Ask your question here
Need help?
Do you have a question about the Panasonic and is the answer not in the manual?
Question and answer
Number of questions: 0