7) Press qw to select “hour” or “minute”, and press as or the number (<0> - <9>) buttons to set a
time, and then press the <ENTER> button.
8) Press asqw to select [COMMAND].
9) Press the <ENTER> button.
fThe [COMMAND] detailed screen is displayed.
10) Press as to select a [COMMAND].
fFor [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time you press qw.
fWhen [INPUT] is selected, press the <ENTER> button, and then press asqw to select the input to set.
[COMMAND]
Detailed settings of
[COMMAND]
Description
[POWER ON]―Switches on the projector.
[STANDBY]―Enters standby.
[SHUTTER]
[OPEN]Opens the shutter.
[CLOSE]Closes the shutter.
[INPUT]
[VIDEO]Switches the input to VIDEO.
[RGB1]Switches the input to RGB1.
[RGB2]Switches the input to RGB2.
[DVI-D]Switches the input to DVI-D.
[HDMI]Switches the input to HDMI.
[DIGITAL LINK]Switches the input to DIGITAL LINK.
[SDI]
*1
Switches the input to SDI.
[INPUT1] - [INPUT10]
*2
Switches the input to DIGITAL LINK, and switch the input of the
Panasonic twisted-pair-cable transmitter to the specied input.
[LAMP SELECT]
[DUAL]Turns on two lamps.
[SINGLE]
Turns on one lamp. (The lamp with shorter runtime will
automatically light.)
[LAMP POWER]
[NORMAL]Sets the lamp brightness to high luminance.
[ECO]Sets the lamp brightness to low luminance.
[P IN P]
[OFF]P IN P function is not used.
[USER1]Lays out the sub-screen with the settings of [USER1].
[USER2]Lays out the sub-screen with the settings of [USER2].
[USER3]Lays out the sub-screen with the settings of [USER3].
*1 Only for PT-DZ870E
*2 When the Panasonic twisted-pair-cable transmitter (such as the optional Digital Interface Box (Model No.: ET-YFB100G)) is connected to the
projector, its input name is reected from [INPUT1] to [INPUT10] automatically. If an item where the input name is not reected is selected, it
is disabled.
11) Press the <ENTER> button.
fThe command is xed and n is displayed at the left of the selected command.
fAfter the command is xed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
fIf you attempt to register the setting that would make the lamp turn on for a short time, an error message will be displayed on the screen.
Set the time and command again.
fTo delete a command already set, press the <DEFAULT> button on the remote control at the screen in Step 5), or select [DELETE] at the
screen in Step 6) and press the <ENTER> button.
fIf multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
fThe operating time will be the local time. (x page 121)
fIf an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with this function may not be executed.
[STARTUP INPUT SELECT]
Set the input when the projector is switched on to start projection.
1) Press as to select [STARTUP INPUT SELECT].
2) Press the <ENTER> button.
fThe [STARTUP INPUT SELECT] screen is displayed.
Manual
View the manual for the Panasonic PT-DX100EWJ here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 6.9. This manual is available in the following languages: English. Do you have a question about the Panasonic PT-DX100EWJ or do you need help? Ask your question here
Need help?
Do you have a question about the Panasonic and is the answer not in the manual?
Question and answer
Number of questions: 0